ASTM A 449 : 2014
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Hex Cap Screws, Bolts and Studs, Steel, Heat Treated, 120/105/90 ksi Minimum Tensile Strength, General Use
Hardcopy , PDF
08-12-2020
English
27-10-2014
Important note : Users cannot be edited or removed once added to your Multi user PDF.| Committee |
F 16
|
| DocumentType |
Standard
|
| Pages |
7
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This specification2 covers quenched and tempered steel hex cap screws, bolts, and studs having a minimum tensile strength of 120 ksi for diameters 1.0 in. and smaller; 105 ksi for diameters over 1.0 in. to 11/2in.; and 90 ksi for diameters 13/4in. to 3.0 in. inclusive. The term "fasteners" in this specification denotes hex cap screws, bolts, and studs.
1.2The fasteners are intended for general engineering use.
1.3The fasteners are furnished in diameters 1/4to 3.0 in. inclusive. They are designated by type denoting chemical composition as follows:
| Type | Description |
| Type I | Plain carbon steel, carbon boron steel, alloy steel, or alloy boron steel |
| Type 2 | Withdrawn 2003 |
| Type 3 | Weathering steel |
1.4Terms used in this specification are defined in Terminology F1789 unless otherwise defined in this specification.
1.5The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.
1.6This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| ANSI/AWWA C606:2022 | Grooved and Shouldered Joints |
| API RP 697:2023 | Pump Repair |
| ANSI/MSS SP-58:2018 | PIPE HANGERS AND SUPPORTS Materials, Design, Manufacture, Selection, Application, and Installation (ANSI-approved American National Standard) |
| ASTM F 1789 : 2014 : REV A | Standard Terminology for F16 Mechanical Fasteners |
| ASTM F 1789 : 2016 | Standard Terminology for F16 Mechanical Fasteners |
| ASTM F 1470 : 2012 | Standard Practice for Fastener Sampling for Specified Mechanical Properties and Performance Inspection |
| ASTM F 1789 : 2017 | Standard Terminology for F16 Mechanical Fasteners |
| ASTM F 2329 : 2005 | Standard Specification for Zinc Coating, Hot-Dip, Requirements for Application to Carbon and Alloy Steel Bolts, Screws, Washers, Nuts, and Special Threaded Fasteners |
| ASTM F 2329 : 2011 | Standard Specification for Zinc Coating, Hot-Dip, Requirements for Application to Carbon and Alloy Steel Bolts, Screws, Washers, Nuts, and Special Threaded Fasteners |
| ASTM F 1789 : 2008 | Standard Terminology for F16 Mechanical Fasteners |
| ASTM F 1789 : 2006 : REV A | Standard Terminology for F16 Mechanical Fasteners |
| ASTM F 1789 : 2001 : REV A | Standard Terminology of F16 Mechanical Fasteners |
| ASTM F 1470 : 2002 | Standard Guide for Fastener Sampling for Specified Mechanical Properties and Performance Inspection |
| ASTM F 1789 : 2017 : REV A | Standard Terminology for F16 Mechanical Fasteners |
| ASTM F 1789 : 2012 : REV A | Standard Terminology for F16 Mechanical Fasteners |
| ASTM F 1789 : 2001 : REV B | Standard Terminology of F16 Mechanical Fasteners |
| ASTM F 1789 : 2005 : REV C | Standard Terminology for F16 Mechanical Fasteners |
| ASTM F 1470 : 2009 | Standard Practice for Fastener Sampling for Specified Mechanical Properties and Performance Inspection |
| ASTM F 1789 : 2003 : REV A | Standard Terminology for F16 Mechanical Fasteners |
| ASTM F 1789 : 2008 : REV B | Standard Terminology for F16 Mechanical Fasteners |
| ASTM F 1789 : 2006 : REV B | Standard Terminology for F16 Mechanical Fasteners |
| ASTM F 1789 : 2014 | Standard Terminology for F16 Mechanical Fasteners |
| ASTM F 1789 : 2002 : REV A | Standard Terminology of F16 Mechanical Fasteners |
| ASTM F 1789 : 2009 : REV A | Standard Terminology for F16 Mechanical Fasteners |
| ASTM F 1789 : 2006 : REV C | Standard Terminology for F16 Mechanical Fasteners |
| ASTM F 1789 : 2004 : REV B | Standard Terminology for F16 Mechanical Fasteners |
| ASTM F 2329 : 2005 : R2011 | Standard Specification for Zinc Coating, Hot-Dip, Requirements for Application to Carbon and Alloy Steel Bolts, Screws, Washers, Nuts, and Special Threaded Fasteners |
| ASTM F 1789 : 2007 : REV C | Standard Terminology for F16 Mechanical Fasteners |
| ASTM F 1789 : 2007 : REV A | Standard Terminology for F16 Mechanical Fasteners |
| ASTM F 1789 : 2008 : REV C | Standard Terminology for F16 Mechanical Fasteners |
| ASTM F 1789 : 2015 | Standard Terminology for F16 Mechanical Fasteners |
| ASTM F 1789 : 2002 : REV B | Standard Terminology of F16 Mechanical Fasteners |
| ASTM F 1789 : 2010 : REV A | Standard Terminology for F16 Mechanical Fasteners |
| ASTM F 1789 : 2012 | Standard Terminology for F16 Mechanical Fasteners |
| ASTM F 1789 : 2005 : REV D | Standard Terminology for F16 Mechanical Fasteners |
| ASTM F 2329 : 2013 | Standard Specification for Zinc Coating, Hot-Dip, Requirements for Application to Carbon and Alloy Steel Bolts, Screws, Washers, Nuts, and Special Threaded Fasteners |
| ASTM F 1789 : 2010 : REV B | Standard Terminology for F16 Mechanical Fasteners |
| ASTM F 1789 : 2010 : REV A : EDT 1 | Standard Terminology for F16 Mechanical Fasteners |
| ASTM F 1789 : 2015 : REV A | Standard Terminology for F16 Mechanical Fasteners |
| ASTM F 1789 : 2000 : REV A | Standard Terminology of F16 Mechanical Fasteners |
| ASTM F 1470 : 2018 | Standard Practice for Fastener Sampling for Specified Mechanical Properties and Performance Inspection |
| ASTM F 1789 : 2007 : REV B | Standard Terminology for F16 Mechanical Fasteners |
| ASTM F 1789 : 2011 : REV B | Standard Terminology for F16 Mechanical Fasteners |
| ASTM F 1470 : 2001 | Standard Guide for Fastener Sampling for Specified Mechanical Properties and Performance Inspection |
| ASTM F 1789 : 2004 : REV A | Standard Terminology for F16 Mechanical Fasteners |
| ASTM F 1789 : 2005 : REV A | Standard Terminology for F16 Mechanical Fasteners |
| ASTM F 1470 : 2019 | Standard Practice for Fastener Sampling for Specified Mechanical Properties and Performance Inspection |
| ASTM F 1789 : 2008 : REV D | Standard Terminology for F16 Mechanical Fasteners |
| ASTM F 1789 : 2007 | Standard Terminology for F16 Mechanical Fasteners |
| ASTM F 1789 : 2008 : REV A | Standard Terminology for F16 Mechanical Fasteners |
| ASTM F 1789 : 2011 : REV A | Standard Terminology for F16 Mechanical Fasteners |
| ASTM F 1789 : 2005 : REV B | Standard Terminology for F16 Mechanical Fasteners |
| ASTM F 1789 : 2002 | Standard Terminology of F16 Mechanical Fasteners |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.