ASTM A 587 : 2022
Current
The latest, up-to-date edition.
Standard Specification for Electric-Resistance-Welded Low-Carbon Steel Pipe for the Chemical Industry
Hardcopy , PDF
English
17-10-2022
Committee |
A 01
|
DocumentType |
Standard
|
Pages |
6
|
PublisherName |
American Society for Testing and Materials
|
Status |
Current
|
Supersedes |
1.1This specification2 covers electric-resistance-welded low-carbon steel pipe intended for use as process lines.
1.2Pipe ordered under this specification shall be suitable for severe forming operations involving flanging in all sizes and bending to close radii up to and including NPS 4 [DN 100].
1.3This specification covers NPS 1/2[DN 15] through NPS 10 [DN 250], plus additional sizes. The corresponding outside diameters and wall thicknesses for NPS 1/2[DN 15] through 10 [DN 250] are listed in Table 1, as are the dimensions for the additional sizes.
Note 1:The dimensionless designator NPS [DN] (nominal pipe size) has been substituted in this standard for such traditional terms as “nominal diameter,” “size,” and “nominal size.”
1.4Units—This specification is expressed in both inch-pound units and in SI units; however, unless the purchase order or contract specifies the applicable M specification designation (SI units), the inch-pound units shall apply. The values stated in either inchpound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.
1.5The following precautionary caveat pertains only to the test method portion, Sections 7, 13, and 14, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM F 2014 : 2000 : R2019 | Standard Specification for Non-Reinforced Extruded Tee Connections for Piping Applications |
ASTM F 2015 : 2000 : R2019 | Standard Specification for Lap Joint Flange Pipe End Applications |
ASTM F 1545 : 2015 : REV A : R2021 | Standard Specification for Plastic-Lined Ferrous Metal Pipe, Fittings, and Flanges |
ASTM A 370 : 2021 | Standard Test Methods and Definitions for Mechanical Testing of Steel Products |
ASTM A 53/A53M : 2020 | Standard Specification for Pipe, Steel, Black and Hot-Dipped, Zinc-Coated, Welded and Seamless |
ASTM A 370 : 2024 : REV A | Standard Test Methods and Definitions for Mechanical Testing of Steel Products |
ASTM A 53/A53M : 2024 | Standard Specification for Pipe, Steel, Black and Hot-Dipped, Zinc-Coated, Welded and Seamless |
ASTM A 941 : 2023 | Standard Terminology Relating to Steel, Stainless Steel, Related Alloys, and Ferroalloys |
ASTM A 941 : 2024 : REV A | Standard Terminology Relating to Steel, Stainless Steel, Related Alloys, and Ferroalloys |
ASTM A 370 : 2023 | Standard Test Methods and Definitions for Mechanical Testing of Steel Products |
ASTM A 941 : 2022 : REV A | Standard Terminology Relating to Steel, Stainless Steel, Related Alloys, and Ferroalloys |
ASTM A 941 : 2024 | Standard Terminology Relating to Steel, Stainless Steel, Related Alloys, and Ferroalloys |
ASTM A 370 : 2022 | Standard Test Methods and Definitions for Mechanical Testing of Steel Products |
ASTM E 309 : 2016 | Standard Practice for Eddy Current Examination of Steel Tubular Products Using Magnetic Saturation |
ASTM A 53/A53M : 2022 | Standard Specification for Pipe, Steel, Black and Hot-Dipped, Zinc-Coated, Welded and Seamless |
ASTM A 941 : 2024 : REV B | Standard Terminology Relating to Steel, Stainless Steel, Related Alloys, and Ferroalloys |
ASTM E 309 : 2024 | Standard Practice for Eddy Current Examination of Steel Tubular Products |
ASTM A 370 : 2024 | Standard Test Methods and Definitions for Mechanical Testing of Steel Products |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.