ASTM A 635/A635M : 2015 : REDLINE
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Steel, Sheet and Strip, Heavy-Thickness Coils, Hot-Rolled, Alloy, Carbon, Structural, High-Strength Low-Alloy, and High-Strength Low-Alloy with Improved Formability, General Requirements for
08-10-2022
English
16-11-2015
Important note : Users cannot be edited or removed once added to your Multi user PDF.CONTAINED IN VOL. 01.03, 2017 Describes the general requirements for hot-rolled, heavy-thickness sheet and strip in coils.
| Committee |
A 01
|
| DevelopmentNote |
Supersedes ASTM A 635M (05/2002)
|
| DocumentType |
Redline
|
| Pages |
15
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy |
1.1This specification covers the general requirements for hot-rolled, heavy-thickness sheet and strip in coils.
1.2It applies to Specifications A414/A414M, A424/A424M, and A1018/A1018M.
1.3This material is available only in coils described as follows:
| Size Limits, Coils Only | ||
| Product | Width, in. [mm] | Thickness, in. [mm] |
| Strip | over 8 to 12, incl | 0.230 to 1.000, incl |
| Sheet | All WidthsA | 0.230 to 1.000, incl |
Note 1:The changes in width limits with the publication of A635/A635M – 06a result in a change in tensile testing direction for material from 0.180 in. [4.5 mm] to 0.230 in. exclusive [6.0 mm exclusive] over 48 in. [1200 mm] wide, as that material is now covered by Specification A568/A568M – 06a. The purchaser is advised to discuss this change with the supplier.
1.4In case of any conflict in requirements, the requirements of the individual material specification shall prevail over those of this general specification.
1.5Annex A1 lists permissible variations in dimensions and mass (see Note 2) in SI [metric] units. The values listed are not exact conversions of the values listed in the inch-pound tables, but instead are rounded or rationalized values. Conformance to Annex A1 is mandatory when the “M” specification is used.
Note 2:The term weight is used when inch-pound units are the standard. However, under SI, the preferred term is mass.
1.6The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.7This specification and the applicable material specifications are expressed in both inch-pound units and SI units. However, unless the order specifies the applicable “M” specification designation (SI units), the material shall be furnished to inch-pound units.
| ASTM A 659/A659M : 2012 | Standard Specification for Commercial Steel (CS), Sheet and Strip, Carbon (0.16 Maximum to 0.25 Maximum Percent), Hot-Rolled |
| ASTM A 1031/A1031M : 2012 | Standard Specification for Steel, Sheet and Strip, Heavy-Thickness Coils, Alloy, Drawing Steel and Structural Steel, Hot-Rolled |
| IEEE C135.80-2012 | IEEE Standard for Fasteners for Overhead Line Construction |
| ASTM F 1217 : 2017 : REDLINE | Standard Specification for Cooker, Steam |
| ASTM F 1047 : 2017 : REDLINE | Standard Specification for Frying and Braising Pans, Tilting Type |
| ASTM A 414/A414M : 2014 : REDLINE | Standard Specification for Steel, Sheet, Carbon, and High-Strength, Low-Alloy for Pressure Vessels |
| ASTM A 1073/A1073M : 2017 : REDLINE | Standard Practice for Using Hand Micrometers to Measure the Thickness of Uncoated Steel Sheet and Nonmetallic and Metallic-Coated Steel Sheet |
| AWWA C301 : 2014 | PRESTRESSED CONCRETE PRESSURE PIPE, STEEL-CYLINDER TYPE |
| ASTM A 1031 : 2005 | Standard Specification for Steel, Sheet and Strip, Heavy-Thickness Coils, Alloy, Drawing Steel and Structural Steel, Hot-Rolled |
| ASTM A 659/A659M : 2012 : R2017 | Standard Specification for Commercial Steel (CS), Sheet and Strip, Carbon (0.16 Maximum to 0.25 Maximum Percent), Hot-Rolled |
| ASTM A 424/A424M : 2009 : REV A : R2016 | Standard Specification for Steel, Sheet, for Porcelain Enameling |
| ASTM A 769/A769M : 2017 : REDLINE | Standard Specification for Carbon and High-Strength Electric Resistance Forge-Welded Steel Structural Shapes |
| ASTM A 569/A569M : 1998 | Standard Specification for Steel, Carbon (0.15 Maximum, Percent), Hot-Rolled Sheet and Strip Commercial (Withdrawn 2000) |
| CSA G401 : 2014 | CORRUGATED STEEL PIPE PRODUCTS |
| ASTM F 1247 : 1989 : R2005 | Standard Specification for Intrusion Resistant Generic Vault Structures |
| ASTM F 1090 : 2015 : REDLINE | Standard Classification for Bank and Mercantile Vault Construction |
| ASTM F 1247 : 1989 : R1996 : EDT 1 | Standard Specification for Intrusion Resistant Generic Vault Structures |
| FM 1951,52,53 : 2016 | PIPE HANGER COMPONENTS FOR AUTOMATIC SPRINKLER SYSTEMS |
| MIL-D-43699 Revision C:1987 | DRUMS, FABRIC, COLLAPSIBLE, (DRINKING WATER, 55-,250- & 500 GALLON CAPACITIES) |
| ASTM A 1031/A1031M : 2012 : R2017 | Standard Specification for Steel, Sheet and Strip, Heavy-Thickness Coils, Alloy, Drawing Steel and Structural Steel, Hot-Rolled |
| IEEE C135.90-2014 | IEEE Standard for Pole Line Hardware for Overhead Line Construction |
| ANSI/AWWA C300 : 2016 | REINFORCED CONCRETE PRESSURE PIPE, STEEL - CYLINDER TYPE |
| AWWA C302 : 2016 | REINFORCED CONCRETE PRESSURE PIPE, NONCYLINDER TYPE |
| SAE J126_201504 | Selecting and Specifying Hot and Cold Rolled Steel Sheet and Strip |
| ASTM A 424/A424M : 2009 | Standard Specification for Steel, Sheet, for Porcelain Enameling |
| ASTM A 424/A424M : 2009 : REV A | Standard Specification for Steel, Sheet, for Porcelain Enameling |
| ASTM A 786/A786M : 2015 : REDLINE | Standard Specification for Hot-Rolled Carbon, Low-Alloy, High-Strength Low-Alloy, and Alloy Steel Floor Plates |
| MIL-STD-129 Revision R:2014 | Military Marking for Shipment and Storage |
| ASTM A 414/A414M : 2014 : REDLINE | Standard Specification for Steel, Sheet, Carbon, and High-Strength, Low-Alloy for Pressure Vessels |
| FED-STD-123 Revision H:2007 | MARKING FOR SHIPMENT (CIVIL AGENCIES) |
| ASTM A 700 : 2014 | Standard Guide for Packaging, Marking, and Loading Methods for Steel Products for Shipment |
| ASTM E 11 : 2017 : REDLINE | Standard Specification for Woven Wire Test Sieve Cloth and Test Sieves |
| ASTM A 1073/A1073M : 2017 : REDLINE | Standard Practice for Using Hand Micrometers to Measure the Thickness of Uncoated Steel Sheet and Nonmetallic and Metallic-Coated Steel Sheet |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.