ASTM A 674 : 2018
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Practice for Polyethylene Encasement for Ductile Iron Pipe for Water or Other Liquids
Hardcopy , PDF
08-11-2022
English
05-12-2018
Important note : Users cannot be edited or removed once added to your Multi user PDF.This practice covers materials and installation procedures for polyethylene encasement to be applied to underground installations of ductile iron pipe.
| Committee |
A 04
|
| DocumentType |
Standard Practice
|
| Pages |
8
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This practice covers materials and installation procedures for polyethylene encasement to be applied to underground installations of ductile iron pipe. It may also be used for polyethylene encasement of fittings, valves, and other appurtenances to ductile iron pipe systems.
1.2The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.2.1Important SI values are provided in brackets. Also, certain important SI values appear without brackets or parentheses.
1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM D 1922 : 2008 | Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method |
| ASTM D 1709 : 2022 | Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method |
| ASTM D 1709 : 2004 | Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method |
| ASTM D 4976 : 2006 | Standard Specification for Polyethylene Plastics Molding and Extrusion Materials |
| ASTM D 4976 : 2000 : REV B | Standard Specification for Polyethylene Plastics Molding and Extrusion Materials |
| ASTM D 4976 : 2004 : REV A | Standard Specification for Polyethylene Plastics Molding and Extrusion Materials |
| ASTM D 1922 : 2015 | Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method |
| ASTM D 1922 : 2006 : REV A | Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method |
| ASTM D 4976 : 2004 | Standard Specification for Polyethylene Plastics Molding and Extrusion Materials |
| ASTM D 1709 : 2015 | Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method |
| ASTM D 4976 : 2012 | Standard Specification for Polyethylene Plastics Molding and Extrusion Materials |
| ASTM D 1922 : 2003 | Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method |
| ASTM D 1709 : 2009 | Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method |
| ASTM D 1709 : 1998 | Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method |
| ASTM D 4976 : 2002 | Standard Specification for Polyethylene Plastics Molding and Extrusion Materials |
| ASTM D 1709 : 2001 | Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method |
| ASTM D 1709 : 2016 | Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method |
| ASTM D 1922 : 2015 : R2020 | Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method |
| ASTM D 1709 : 2008 | Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method |
| ASTM D 1922 : 2003 : REV A | Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method |
| ASTM D 4976 : 2002 : EDT 1 | Standard Specification for Polyethylene Plastics Molding and Extrusion Materials |
| ASTM D 1922 : 2005 | Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method |
| ASTM D 1709 : 2016 : REV A : EDT 1 | Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method |
| ASTM D 1709 : 2003 | Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method |
| ASTM D 1922 : 2000 : REV A | Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method |
| ASTM D 1922 : 2006 | Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method |
| ASTM D 1709 : 2015 : REV A | Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method |
| ASTM D 1922 : 2009 | Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method |
| ASTM D 4976 : 2012 : REV A | Standard Specification for Polyethylene Plastics Molding and Extrusion Materials |
| ASTM D 1709 : 2016 : REV A | Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.