ASTM A 74 : 2017
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Cast Iron Soil Pipe and Fittings
Hardcopy , PDF
09-05-2020
English
01-10-2017
Important note : Users cannot be edited or removed once added to your Multi user PDF.This specification covers cast iron soil pipe and fittings for use in gravity flow plumbing, drain, waste and vent sanitary, and storm water applications.
| Committee |
A 04
|
| DocumentType |
Standard
|
| Pages |
45
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This specification covers cast iron soil pipe and fittings for use in gravity flow plumbing, drain, waste and vent sanitary, and storm water applications. It establishes standards covering material, manufacture, mechanical and chemical properties, coating, test methods, inspection, certification, product markings, dimensions, and dimensional tolerances for extra heavy and service cast iron soil pipe and fittings. These pipe and fittings are not intended for pressure applications as the selection of the proper size for sanitary drain, waste, vent, and storm drain systems allows free air space for gravity drainage.
1.2This specification covers pipe and fittings of the following patterns and, when so designated, shall apply to any other patterns that conform with the applicable requirements given in this specification.
1.2.1Pipe:
| Tables | |
| Extra heavy, 21/2ft (0.75 m), 31/2ft (1.0 m), 5 ft (1.5 m), 10 ft (3.0 m) lengths | 1, 2 |
| Service, 21/2ft (0.75 m), 31/2ft (1.0 m), 5 ft (1.5 m), 10 ft (3.0 m) | 1, 2 |
| Outside dimensions (for detailing) | X1.1 |
1.2.2Fittings:
| Tables | |
| 1/4bends; long 1/4bends | 3, 4 |
| 1/4bends, long low-hub | 5 |
| 1/4bends, low heel; high heel | 6, 7 |
| 1/4bends, short sweep; long sweep | 8 |
| 1/4bends, reducing long sweep | 9 |
| 1/5bends | 10 |
| 1/6bends | 10 |
| 1/8bends; long 1/8bends | 11 |
| 1/16bends | 11 |
| Y branches | 12, 13 |
| Y branches, combination 1/8bends, single | 14 |
| Y branches, combination 1/8bends, double | 14 |
| Sanitary T branches, single | 15 |
| Sanitary T branches, double | 15 |
| Sanitary T branches, cleanout | 16 |
| Tapped sanitary T branches, single | 17 |
| Tapped sanitary T branches, double | 17 |
| T branches, single and double | 18 |
| Tapped T branches, single | 19 |
| Tapped T branches, double | 19 |
| T branches, cleanout | 20 |
| -45° offset fitting | 21 |
| Double hubs | 22 |
| Long double hubs | 22 |
| Reducers | 23 |
| Increasers | 24, 25 |
| P traps | 26, 27 |
| Deep seal P traps | 28 |
| Running traps | 29 |
| Screw plugs (brass) | 30 |
| Blind plugs | 31 |
| Iron-body ferrules | 32 |
| Side inlets | Fig. 3 |
| Closet bends | 33 |
| Tapping bosses | 34 |
| Reducing 1/4bend SV | 35 |
| Combination Y and 1/8bend | 36 |
| ‘H’ branch fitting | 37 |
1.3The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM D 3960 : 2005 : R2018 | Standard Practice for Determining Volatile Organic Compound (VOC) Content of Paints and Related Coatings |
| ASTM D 1248 : 2002 | Standard Specification for Polyethylene Plastics Extrusion Materials For Wire and Cable |
| ASTM D 3960 : 2002 | Standard Practice for Determining Volatile Organic Compound (VOC) Content of Paints and Related Coatings |
| ASTM D 1248 : 1984 : R1989 : EDT 1 | Standard Specification for Polyethylene Plastics Molding and Extrusion Materials |
| ASTM D 3960 : 2001 | Standard Practice for Determining Volatile Organic Compound (VOC) Content of Paints and Related Coatings |
| ASTM E 1645 : 2001 : R2007 | Standard Practice for Preparation of Dried Paint Samples by Hotplate or Microwave Digestion for Subsequent Lead Analysis |
| ASTM D 1248 : 2012 | Standard Specification for Polyethylene Plastics Extrusion Materials for Wire and Cable |
| ASTM D 3960 : 2005 | Standard Practice for Determining Volatile Organic Compound (VOC) Content of Paints and Related Coatings |
| ASTM E 2349 : 2018 | Standard Practice for Safety Requirements in Metal Casting Operations: Sand Preparation, Molding, and Core Making; Melting and Pouring; and Cleaning and Finishing |
| ASTM D 3960 : 2005 : R2013 | Standard Practice for Determining Volatile Organic Compound (VOC)Content of Paints and Related Coatings |
| ASTM E 1645 : 1994 | Standard Practice for the Preparation of Dried Paint Samples by Hotplate or Microwave Digestion for Subsequent Lead Analysis |
| ASTM D 1248 : 2016 | Standard Specification for Polyethylene Plastics Extrusion Materials for Wire and Cable |
| ASTM E 1645 : 2016 | Standard Practice for Preparation of Dried Paint Samples by Hotplate or Microwave Digestion for Subsequent Lead Analysis |
| ASTM E 1645 : 2001 | Standard Practice for the Preparation of Dried Paint Samples by Hotplate or Microwave Digestion for Subsequent Lead Analysis |
| ASTM E 2349 : 2009 | Standard Practice for Safety Requirements in Metal Casting Operations: Sand Preparation, Molding, and Core Making; Melting and Pouring; and Cleaning and Finishing |
| ASTM D 3960 : 1998 | Standard Practice for Determining Volatile Organic Compound (VOC) Content of Paints and Related Coatings |
| ASTM D 1248 : 2004 | Standard Specification for Polyethylene Plastics Extrusion Materials For Wire and Cable |
| ASTM E 2349 : 2012 | Standard Practice for Safety Requirements in Metal Casting Operations: Sand Preparation, Molding, and Core Making; Melting and Pouring; and Cleaning and Finishing |
| ASTM E 2349 : 2019 | Standard Practice for Safety Requirements in Metal Casting Operations: Sand Preparation, Molding, and Core Making; Melting and Pouring; and Cleaning and Finishing |
| ASTM E 2349 : 2005 | Standard Practice for Safety Requirements in Metal Casting Operations: Sand Preparation, Molding, and Core Making; Melting and Pouring; and Cleaning and Finishing |
| ASTM D 3960 : 2004 | Standard Practice for Determining Volatile Organic Compound (VOC) Content of Paints and Related Coatings |
| ASTM E 1645 : 2001 : R2016 : EDT 1 | Standard Practice for Preparation of Dried Paint Samples by Hotplate or Microwave Digestion for Subsequent Lead Analysis |
| ASTM D 1248 : 2000 : REV A | Standard Specification for Polyethylene Plastics Extrusion Materials For Wire and Cable |
| ASTM D 1248 : 2005 | Standard Specification for Polyethylene Plastics Extrusion Materials For Wire and Cable |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.