![header thumbnail](/images/publishers\astm_cover.gif)
ASTM A 755/A755M : 2018
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
![header thumbnail](/images/publishers\astm_cover.gif)
Standard Specification for Steel Sheet, Metallic Coated by the Hot-Dip Process and Prepainted by the Coil-Coating Process for Exterior Exposed Building Products
Hardcopy , PDF
08-04-2024
English
20-12-2018
This specification covers steel sheet metallic coated by the hot-dip process and coil-coated with organic films for exterior exposed building products. Sheet of this designation is furnished in coils, cut lengths, and formed cut lengths.
Committee |
A 05
|
DocumentType |
Standard
|
Pages |
6
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
1.1This specification covers steel sheet metallic coated by the hot-dip process and coil-coated with organic films for exterior exposed building products. Sheet of this designation is furnished in coils, cut lengths, and formed cut lengths. Building products include corrugated and various types of roll and brake-formed configurations.
1.2The substrate is available in several different metallic-coated steel sheet products as enumerated in 4.1, depending on the requirements of the purchaser.
1.3Coating systems supplied under this specification consist of a primer coat covered by various types and thicknesses of top coats. The combination of primer and top coat is classed as either a two-coat thin-film system or as a two-coat (or more) thick-film system. Typical top-coating materials are: polyester, silicone polyester, acrylic, fluoropolymer, plastisol, or polyurethane.
1.4This specification is applicable to orders in either inch-pound units (as A755) or SI units [as A755M]. Values in inch-pound units and SI units are not necessarily equivalent. Within the text, SI units are shown in brackets. Each system shall be used independently of each other.
1.5Unless the order specifies the “M” designation (SI units), the product shall be furnished to inch-pound units.
1.6The text of this specification references notes and footnotes that provide explanatory material. These notes and footnotes, excluding those in tables and figures, shall not be considered as requirements of this specification.
1.7This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.8This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM A 1122/A1122M : 2022 | Standard Test Method for Bend Testing of Metallic-Coated Steel Sheet to Evaluate Coating Adhesion |
ASTM A 1003/A1003M : 2015 | Standard Specification for Steel Sheet, Carbon, Metallic- and Nonmetallic-Coated for Cold-Formed Framing Members |
ASTM A 924/A924M : 2020 | Standard Specification for General Requirements for Steel Sheet, Metallic-Coated by the Hot-Dip Process |
ASTM A 875/A875M : 2013 | Standard Specification for Steel Sheet, Zinc-5 % Aluminum Alloy-Coated by the Hot-Dip Process |
ASTM D 1005 : 1995 : R2020 | Standard Test Method for Measurement of Dry-Film Thickness of Organic Coatings Using Micrometers |
ASTM A 653/A653M : 2001 : REV A | Standard Specification for Steel Sheet, Zinc-Coated (Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed) by the Hot-Dip Process |
ASTM D 3363 : 2022 | Standard Test Method for Film Hardness by Pencil Test |
ASTM A 1063/A1063M : 2021 | Standard Specification for Steel Sheet, Twin-Roll Cast, Zinc-Coated (Galvanized) by the Hot-Dip Process |
ASTM D 3359 : 2009 : EDT 2 | Standard Test Methods for Measuring Adhesion by Tape Test |
ASTM D 2244 : 2021 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
ASTM D 3363 : 2005 : R2011 : EDT 2 | Standard Test Method for Film Hardness by Pencil Test (Withdrawn 2020) |
ASTM D 2247 : 2010 | Standard Practice for Testing Water Resistance of Coatings in 100% Relative Humidity |
ASTM D 5796 : 2010 : R2015 | Standard Test Method for Measurement of Dry Film Thickness of Thin-Film Coil-Coated Systems by Destructive Means Using a Boring Device |
ASTM A 924/A924M : 2022 | Standard Specification for General Requirements for Steel Sheet, Metallic-Coated by the Hot-Dip Process |
ASTM D 5796 : 2003 | Standard Test Method for Measurement of Dry Film Thickness of Thin Film Coil-Coated Systems by Destructive Means Using a Boring Device |
ASTM A 653/A653M : 2023 | Standard Specification for Steel Sheet, Zinc-Coated (Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed) by the Hot-Dip Process |
ASTM D 2244 : 2015 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
ASTM D 1735 : 2021 | Standard Practice for Testing Water Resistance of Coatings Using Water Fog Apparatus |
ASTM D 5402 : 2006 | Standard Practice for Assessing the Solvent Resistance of Organic Coatings Using Solvent Rubs |
ASTM D 2244 : 2023 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
ASTM A 463/A463M : 2015 : R2020 : EDT 1 | Standard Specification for Steel Sheet, Aluminum-Coated, by the Hot-Dip Process |
ASTM D 2244 : 2011 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
ASTM G 85 : 2019 | Standard Practice for Modified Salt Spray (Fog) Testing |
ASTM D 1735 : 1999 | Standard Practice for Testing Water Resistance of Coatings Using Water Fog Apparatus |
ASTM D 2794 : 1993 : R2024 | Standard Test Method for Resistance of Organic Coatings to the Effects of Rapid Deformation (Impact) |
ASTM A 902 : 2023 : REV A | Standard Terminology Relating to Metallic Coated Steel Products |
ASTM D 2244 : 2009 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
ASTM D 3363 : 2000 | Standard Test Method for Film Hardness by Pencil Test |
ASTM D 7091 : 2022 | Standard Practice for Nondestructive Measurement of Dry Film Thickness of Nonmagnetic Coatings Applied to Ferrous Metals and Nonmagnetic, Nonconductive Coatings Applied to Non-Ferrous Metals |
ASTM A 924/A924M : 2020 | Standard Specification for General Requirements for Steel Sheet, Metallic-Coated by the Hot-Dip Process |
ASTM A 902 : 2023 | Standard Terminology Relating to Metallic Coated Steel Products |
ASTM A 653/A653M : 2022 | Standard Specification for Steel Sheet, Zinc-Coated (Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed) by the Hot-Dip Process |
ASTM D 2247 : 2011 | Standard Practice for Testing Water Resistance of Coatings in 100% Relative Humidity |
ASTM D 3359 : 1997 | Standard Test Methods for Measuring Adhesion by Tape Test |
ASTM D 2244 : 2002 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
ASTM D 2247 : 2002 | Standard Practice for Testing Water Resistance of Coatings in 100% Relative Humidity |
ASTM D 2244 : 2016 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
ASTM A 792/A792M : 2009 | Standard Specification for Steel Sheet, 55 % Aluminum-Zinc Alloy-Coated by the Hot-Dip Process |
ASTM D 2794 : 1992 | Standard Test Method for Resistence of Organic Coatings to the Effects of Rapid Deformation (Impact) |
ASTM D 1654 : 2005 | Standard Test Method for Evaluation of Painted or Coated Specimens Subjected to Corrosive Environments |
ASTM A 653/A653M : 2020 | Standard Specification for Steel Sheet, Zinc-Coated (Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed) by the Hot-Dip Process |
ASTM D 3363 : 2005 | Standard Test Method for Film Hardness by Pencil Test |
ASTM D 2244 : 2015 : EDT 1 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
ASTM D 2244 : 2009 : REV B | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
ASTM D 3363 : 2020 | Standard Test Method for Film Hardness by Pencil Test |
ASTM D 2244 : 2002 : EDT 1 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
ASTM A 924/A924M : 2022 : REV A | Standard Specification for General Requirements for Steel Sheet, Metallic-Coated by the Hot-Dip Process |
ASTM D 2247 : 1992 | Standard Practice for Testing Water Reistence of Coatings in 100% Relative Humidity |
ASTM D 1005 : 1995 : R2001 | Standard Test Method for Measurement of Dry-Film Thickness of Organic Coatings Using Micrometers |
ASTM A 1063/A1063M : 2020 | Standard Specification for Steel Sheet, Twin-Roll Cast, Zinc-Coated (Galvanized) by the Hot-Dip Process |
ASTM A 875/A875M : 2013 : R2021 | Standard Specification for Steel Sheet, Zinc-5 % Aluminum Alloy-Coated by the Hot-Dip Process |
ASTM D 2244 : 2015 : REV A | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
ASTM A 792/A792M : 2022 | Standard Specification for Steel Sheet, 55 % Aluminum-Zinc Alloy-Coated by the Hot-Dip Process |
ASTM D 7091 : 2020 | Standard Practice for Nondestructive Measurement of Dry Film Thickness of Nonmagnetic Coatings Applied to Ferrous Metals and Nonmagnetic, Nonconductive Coatings Applied to Non-Ferrous Metals |
ASTM D 2247 : 2015 | Standard Practice for Testing Water Resistance of Coatings in 100 % Relative Humidity |
ASTM D 3359 : 2009 | Standard Test Methods for Measuring Adhesion by Tape Test |
ASTM D 5402 : 2019 | Standard Practice for Assessing the Solvent Resistance of Organic Coatings Using Solvent Rubs |
ASTM D 1735 : 2014 | Standard Practice for Testing Water Resistance of Coatings Using Water Fog Apparatus |
ASTM A 875/A875M : 2023 | Standard Specification for Steel Sheet, Zinc-5 % Aluminum Alloy-Coated by the Hot-Dip Process |
ASTM D 7835/D7835M : 2019 | Standard Test Method for Determining the Solvent Resistance of an Organic Coating Using a Mechanical Rubbing Machine |
ASTM A 463/A463M : 2022 | Standard Specification for Steel Sheet, Aluminum-Coated, by the Hot-Dip Process |
ASTM D 3359 : 2022 | Standard Test Methods for Rating Adhesion by Tape Test |
ASTM D 2244 : 2014 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
ASTM D 4214 : 2023 | Standard Test Methods for Evaluating the Degree of Chalking of Exterior Paint Films |
ASTM D 3359 : 2002 | Standard Test Methods for Measuring Adhesion by Tape Test |
ASTM A 875/A875M : 2022 | Standard Specification for Steel Sheet, Zinc-5 % Aluminum Alloy-Coated by the Hot-Dip Process |
ASTM D 3359 : 2009 : EDT 1 | Standard Test Methods for Measuring Adhesion by Tape Test |
ASTM D 822 : 2023 | Standard Practice for Filtered Open-Flame Carbon-Arc Exposures of Paint and Related Coatings |
ASTM D 3363 : 2005 : R2011 : EDT 1 | Standard Test Method for Film Hardness by Pencil Test |
ASTM D 2794 : 1993 : R1999 : EDT 1 | Standard Test Method for Resistance of Organic Coatings to the Effects of Rapid Deformation (Impact) |
ASTM D 2244 : 2005 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
ASTM D 4214 : 1998 | Standard Test Methods for Evaluating the Degree of Chalking of Exterior Paint Films (Withdrawn 2007) |
ASTM D 4145 : 2010 | Standard Test Method for Coating Flexibility of Prepainted Sheet |
ASTM D 1005 : 1995 : R2013 | Standard Test Method for Measurement of Dry-Film Thickness of Organic Coatings Using Micrometers |
ASTM D 2794 : 1993 : R2004 | Standard Test Method for Resistance of Organic Coatings to the Effects of Rapid Deformation (Impact) |
ASTM D 3359 : 2007 | Standard Test Methods for Measuring Adhesion by Tape Test |
ASTM D 4214 : 2007 : R2015 | Standard Test Methods for Evaluating the Degree of Chalking of Exterior Paint Films |
ASTM D 1735 : 2004 | Standard Practice for Testing Water Resistance of Coatings Using Water Fog Apparatus |
ASTM B 117 : 2019 | Standard Practice for Operating Salt Spray (Fog) Apparatus |
ASTM D 4214 : 2007 | Standard Test Methods for Evaluating the Degree of Chalking of Exterior Paint Films |
ASTM D 2247 : 2015 : R2020 | Standard Practice for Testing Water Resistance of Coatings in 100 % Relative Humidity |
ASTM D 7091 : 2013 | Standard Practice for Nondestructive Measurement of Dry Film Thickness of Nonmagnetic Coatings Applied to Ferrous Metals and Nonmagnetic, Nonconductive Coatings Applied to Non-Ferrous Metals |
ASTM A 1046/A1046M : 2022 | Standard Specification for Steel Sheet, Zinc-Aluminum-Magnesium Alloy-Coated by the Hot-Dip Process |
ASTM A 1046/A1046M : 2023 | Standard Specification for Steel Sheet, Zinc-Aluminum-Magnesium Alloy-Coated by the Hot-Dip Process |
ASTM D 1654 : 2008 : R2016 | Standard Test Method for Evaluation of Painted or Coated Specimens Subjected to Corrosive Environments |
ASTM D 2244 : 2007 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
ASTM G 85 : 1998 | Standard Practice for Modified Salt Spray (Fog) Testing |
ASTM A 792/A792M : 2010 : R2015 | Standard Specification for Steel Sheet, 55 % Aluminum-Zinc Alloy-Coated by the Hot-Dip Process |
ASTM D 1735 : 2008 | Standard Practice for Testing Water Resistance of Coatings Using Water Fog Apparatus |
ASTM D 5796 : 2003 : R2010 | Standard Test Method for Measurement of Dry Film Thickness of Thin Film Coil-Coated Systems by Destructive Means Using a Boring Device |
ASTM D 2244 : 2022 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
ASTM D 1654 : 1992 : R2000 | Standard Test Method for Evaluation of Painted or Coated Specimens Subjected to Corrosive Environments |
ASTM A 792/A792M : 2023 | Standard Specification for Steel Sheet, 55 % Aluminum-Zinc Alloy-Coated by the Hot-Dip Process |
ASTM D 7091 : 2021 | Standard Practice for Nondestructive Measurement of Dry Film Thickness of Nonmagnetic Coatings Applied to Ferrous Metals and Nonmagnetic, Nonconductive Coatings Applied to Non-Ferrous Metals |
ASTM D 7091 : 2012 | Standard Practice for Nondestructive Measurement of Dry Film Thickness of Nonmagnetic Coatings Applied to Ferrous Metals and Nonmagnetic, Nonconductive Coatings Applied to Non-Ferrous Metals |
ASTM A 875/A875M : 2021 | Standard Specification for Steel Sheet, Zinc-5 % Aluminum Alloy-Coated by the Hot-Dip Process |
ASTM A 924/A924M : 2009 | Standard Specification for General Requirements for Steel Sheet, Metallic-Coated by the Hot-Dip Process |
ASTM D 5796 : 2010 | Standard Test Method for Measurement of Dry Film Thickness of Thin Film Coil-Coated Systems by Destructive Means Using a Boring Device |
ASTM D 5796 : 1999 | Standard Test Method for Measurement of Dry Film Thickness of Thin Film Coil-Coated Systems by Destructive Means Using a Boring Device |
ASTM D 7091 : 2005 | Standard Practice for Nondestructive Measurement of Dry Film Thickness of Nonmagnetic Coatings Applied to Ferrous Metals and Nonmagnetic, Nonconductive Coatings Applied to Non-Ferrous Metals |
ASTM A 792/A792M : 2021 : REV A | Standard Specification for Steel Sheet, 55 % Aluminum-Zinc Alloy-Coated by the Hot-Dip Process |
ASTM D 4145 : 1983 : R1996 : EDT 1 | Standard Test Method for Coating Flexibility of Prepainted Sheet |
ASTM D 3359 : 2023 | Standard Test Methods for Rating Adhesion by Tape Test |
ASTM D 3363 : 2005 : R2011 | Standard Test Method for Film Hardness by Pencil Test |
ASTM D 1005 : 1995 : R2007 | Standard Test Method for Measurement of Dry-Film Thickness of Organic Coatings Using Micrometers |
ASTM D 7835/D7835M : 2023 | Standard Test Method for Determining the Solvent Resistance of an Organic Coating Using a Mechanical Rubbing Machine |
ASTM A 875/A875M : 2009 | Standard Specification for Steel Sheet, Zinc-5 % Aluminum Alloy-Coated by the Hot-Dip Process |
ASTM D 3359 : 2008 | Standard Test Methods for Measuring Adhesion by Tape Test |
ASTM D 2794 : 1993 : R2019 | Standard Test Method for Resistance of Organic Coatings to the Effects of Rapid Deformation (Impact) |
ASTM D 1735 : 2002 | Standard Practice for Testing Water Resistance of Coatings Using Water Fog Apparatus |
ASTM D 1654 : 2008 | Standard Test Method for Evaluation of Painted or Coated Specimens Subjected to Corrosive Environments |
ASTM D 1654 : 2008 : R2016 : EDT 1 | Standard Test Method for Evaluation of Painted or Coated Specimens Subjected to Corrosive Environments |
ASTM A 792/A792M : 2021 | Standard Specification for Steel Sheet, 55 % Aluminum-Zinc Alloy-Coated by the Hot-Dip Process |
ASTM A 1063/A1063M : 2022 | Standard Specification for Steel Sheet, Twin-Roll Cast, Zinc-Coated (Galvanized) by the Hot-Dip Process |
ASTM D 5402 : 2006 : R2011 | Standard Practice for Assessing the Solvent Resistance of Organic Coatings Using Solvent Rubs |
ASTM D 5402 : 1993 : R1999 | Standard Practice for Assessing the Solvent Resistance of Organic Coatings Using Solvent Rubs |
ASTM D 2244 : 2009 : REV A | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
ASTM D 4145 : 1983 : R2002 | Standard Test Method for Coating Flexibility of Prepainted Sheet |
ASTM D 4145 : 2010 : R2022 | Standard Test Method for Coating Flexibility of Prepainted Sheet |
ASTM D 2244 : 1993 : R2000 | Standard Test Method for Calculation of Color Differences From Instrumentally Measured Color Coordinates |
ASTM A 902 : 2018 : REV A | Standard Terminology Relating to Metallic Coated Steel Products |
ASTM D 2247 : 1968 : R1973 | Standard Method for Testing Coated Metal Specimens At 100% Relative Humidity |
ASTM D 2794 : 1993 : R2010 | Standard Test Method for Resistance of Organic Coatings to the Effects of Rapid Deformation (Impact) |
ASTM D 659 : 1986 : EDT 1 | Method of Evaluating Degree of Chalking of Exterior Paints |
ASTM D 3359 : 2017 | Standard Test Methods for Rating Adhesion by Tape Test |
ASTM D 5796 : 2020 | Standard Test Method for Measurement of Dry Film Thickness of Thin-Film Coil-Coated Systems by Destructive Means Using a Boring Device |
ASTM D 1005 : 1995 | Standard Test Method for Measurement of Dry-Film Thickness of Organic Coatings Using Micrometers |
ASTM D 2247 : 1999 | Standard Practice for Testing Water Resistance of Coatings in 100% Relative Humidity |
ASTM D 4145 : 2010 : R2018 | Standard Test Method for Coating Flexibility of Prepainted Sheet |
ASTM A 1046/A1046M : 2019 | Standard Specification for Steel Sheet, Zinc-Aluminum-Magnesium Alloy-Coated by the Hot-Dip Process |
ASTM D 5402 : 2015 | Standard Practice for Assessing the Solvent Resistance of Organic Coatings Using Solvent Rubs |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.