ASTM A 787/A787M : 2020 : REV A
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Electric-Resistance-Welded Metallic-Coated Carbon Steel Mechanical Tubing
Hardcopy , PDF
02-12-2022
English
20-11-2020
Committee |
A 01
|
DocumentType |
Standard
|
Pages |
10
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
1.1This specification covers round, square, rectangular, and special shape, electric-resistance-welded carbon steel mechanical tubing, either zinc-coated (galvanized) after welding or produced from aluminum-coated, zinc-coated (galvanized), zinc-iron alloy-coated (galvannealed), 55 % aluminum-zinc alloy-coated, or zinc-aluminum-magnesium alloy-coated carbon steel sheet. Tubing for use as electrical conduit (EMT) or intermediate metallic conduit (IMC) is not covered by this specification.
1.1.1The product is available in various grades based on chemical requirements (Sections 5 and 9).
1.1.2The product is available in various Types (Section 3).
1.2This specification covers mechanical tubing with outside diameters or maximum outside dimensions ranging from 1/2to 15 in. [12.7 to 380.0 mm] and wall thickness from 0.028 to 0.180 in. [0.70 to 4.60 mm]. Indeterminate wall thicknesses may be ordered. In those cases the more stringent tolerances of Tables 3, 4, 5, 6, 12 and 13 shall apply.
1.3When sizes within the ranges listed above are ordered, all other requirements of the specification shall be met.
1.4This specification is expressed in both inch-pound units and in SI units; however, unless the purchase order specifies the applicable M specification designation (SI units), the inch-pound units shall apply. The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM A 653/A653M : 2001 : REV A | Standard Specification for Steel Sheet, Zinc-Coated (Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed) by the Hot-Dip Process |
ASTM A 924/A924M : 2022 | Standard Specification for General Requirements for Steel Sheet, Metallic-Coated by the Hot-Dip Process |
ASTM A 463/A463M : 2015 : R2020 : EDT 1 | Standard Specification for Steel Sheet, Aluminum-Coated, by the Hot-Dip Process |
ASTM A 924/A924M : 2020 | Standard Specification for General Requirements for Steel Sheet, Metallic-Coated by the Hot-Dip Process |
ASTM A 653/A653M : 2022 | Standard Specification for Steel Sheet, Zinc-Coated (Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed) by the Hot-Dip Process |
ASTM A 792/A792M : 2009 | Standard Specification for Steel Sheet, 55 % Aluminum-Zinc Alloy-Coated by the Hot-Dip Process |
ASTM A 653/A653M : 2020 | Standard Specification for Steel Sheet, Zinc-Coated (Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed) by the Hot-Dip Process |
ASTM A 924/A924M : 2022 : REV A | Standard Specification for General Requirements for Steel Sheet, Metallic-Coated by the Hot-Dip Process |
ASTM A 792/A792M : 2022 | Standard Specification for Steel Sheet, 55 % Aluminum-Zinc Alloy-Coated by the Hot-Dip Process |
ASTM A 463/A463M : 2022 | Standard Specification for Steel Sheet, Aluminum-Coated, by the Hot-Dip Process |
ASTM A 1046/A1046M : 2022 | Standard Specification for Steel Sheet, Zinc-Aluminum-Magnesium Alloy-Coated by the Hot-Dip Process |
ASTM A 792/A792M : 2010 : R2015 | Standard Specification for Steel Sheet, 55 % Aluminum-Zinc Alloy-Coated by the Hot-Dip Process |
ASTM A 924/A924M : 2009 | Standard Specification for General Requirements for Steel Sheet, Metallic-Coated by the Hot-Dip Process |
ASTM A 792/A792M : 2021 : REV A | Standard Specification for Steel Sheet, 55 % Aluminum-Zinc Alloy-Coated by the Hot-Dip Process |
ASTM A 792/A792M : 2021 | Standard Specification for Steel Sheet, 55 % Aluminum-Zinc Alloy-Coated by the Hot-Dip Process |
ASTM A 1046/A1046M : 2019 | Standard Specification for Steel Sheet, Zinc-Aluminum-Magnesium Alloy-Coated by the Hot-Dip Process |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.