• Shopping Cart
    There are no items in your cart

ASTM A 924/A924M : 2020

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by

Standard Specification for General Requirements for Steel Sheet, Metallic-Coated by the Hot-Dip Process

Available format(s)

Hardcopy , PDF

Superseded date

30-04-2022

Superseded by

ASTM A 924/A924M : 2022

Language(s)

English

Published date

16-09-2020

€74.48
Excluding VAT

Committee
A 05
DocumentType
Standard
Pages
13
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

1.1This specification covers the general requirements that, unless otherwise specified in the product specification, apply to steel sheet in coils and cut lengths, metallic-coated on continuous lines by the hot-dip process. The product is intended for applications requiring corrosion resistance. The product specifications contain requirements for specific strength levels, heat resistance, paintability, or formability, or a combination thereof.

1.2Subject to individual product specification provisions, steel sheet is available as Commercial Steel (CS) Types A, B, and C, Forming Steel (FS), Drawing Steel (DS), Deep Drawing Steel (DDS), Extra Deep Drawing Steel (EDDS), High Temperature Steel (HTS), Structural Steel (SS), and High Strength Low Alloy Steel (HSLAS). Steel sheet is produced with the following metallic coatings. Specific information on each of the following is contained in the individual product specification:

1.2.1Zinc or zinc-iron alloy coated,

1.2.2Zinc-5 % aluminum alloy coated,

1.2.355 % aluminum-zinc alloy coated,

1.2.4Aluminum or aluminum-silicon alloy coated,

1.2.5Zinc-aluminum-magnesium alloy coated.

1.3Products covered by this general requirements specification are described in the following product standards: Specifications A463/A463M; A653/A653M; A755/A755M; A792/A792M; A875/A875M; A929/A929M; A1046/A1046M; A1057/A1057M; A1063/A1063M; and A1079.

1.4Metallic-coated steel sheet is produced to various coating designations, as shown in the individual product specifications. Except for differentially coated sheet, the coating is always expressed as the total coating of both surfaces.

1.5In case of any conflict in requirements, the requirements of the individual product specifications shall prevail over those of this general specification.

1.6The purchaser is permitted to specify additional requirements that do not negate any of the provisions of this general specification or of the individual product specifications. Such additional requirements, the acceptance of which are subject to negotiation with the supplier, shall be included in the order information.

1.7For purposes of determining conformance with this specification and the various product specifications referenced in 1.3, measured values, calculated values, or observed values shall be rounded to the nearest unit in the right-hand place of figures used in expressing the limiting values (except to the nearest 5 MPa for SI strength values) in accordance with the rounding method of Practice E29.

1.7.1Ordered values, identified in tables, specified such as over 30 through 48 or 30 exclusive to 48 inclusive, cover all ordered values specified as 30.1, 30.01, 30.001 etc., up to and including 48.000 etc., but does not cover ordered values specified as 30.000 etc., or less, nor does it cover ordered values specified as 48.1, 48.01, 48.001 etc.

1.8Metallic-coated steel sheet covered by this specification is produced to thickness requirements expressed to 0.001 in. [0.01 mm] for both coils and cut lengths. The thickness is the total of the base steel and the coating.

1.9The text of this specification references notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.

1.10Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.

1.11This specification and some of the applicable product specifications are expressed in both inch-pound and SI units. However, unless the order specifies the applicable “M” specification designation (SI units), the product shall be furnished to inch-pound units.

1.12This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.13This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ASTM A 755/A755M : 2018 Standard Specification for Steel Sheet, Metallic Coated by the Hot-Dip Process and Prepainted by the Coil-Coating Process for Exterior Exposed Building Products
ASTM A 902 : 2018 : REV A Standard Terminology Relating to Metallic Coated Steel Products
ASTM D 5933 : 2019 Standard Specification for 2<fraction><num>5</num><den>8</den></fraction>-in. and 4-in. Diameter Metal Shear Plates for Use in Wood Constructions
ASTM A 1046/A1046M : 2019 Standard Specification for Steel Sheet, Zinc-Aluminum-Magnesium Alloy-Coated by the Hot-Dip Process
ASTM A 1057/A1057M : 2008 : R2019 Standard Specification for Steel, Structural Tubing, Cold Formed, Welded, Carbon, Zinc-Coated (Galvanized) by the Hot-Dip Process
ASTM A 1093/A1093M : 2015 : R2020 : EDT 1 Standard Specification for Electrolytic Plasma Treatment Processing of Conductive Materials
ASTM A 1092 : 2015 : R2020 Standard Specification for Steel Sheet, as Cold-Reduced, for Conversion to Annealed Cold-Rolled Steel Sheet, and Hot Dip Metallic-Coated Steel Sheet
ASTM A 463/A463M : 2015 : R2020 : EDT 1 Standard Specification for Steel Sheet, Aluminum-Coated, by the Hot-Dip Process
ASTM A 653/A653M : 2020 Standard Specification for Steel Sheet, Zinc-Coated (Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed) by the Hot-Dip Process
ASTM A 1076/A1076M : 2020 Standard Specification for Cold Formed Carbon Structural Steel Tubing Made from Metallic Precoated Sheet Steel
ASTM F 1697 : 2018 Standard Specification for Poly(Vinyl Chloride) (PVC) Profile Strip for Machine Spiral-Wound Liner Pipe Rehabilitation of Existing Sewers and Conduit
ASTM D 6255/D6255M : 2018 Standard Specification for Steel or Aluminum Slotted Angle Crates
ASTM A 929/A929M : 2018 Standard Specification for Steel Sheet, Metallic-Coated by the Hot-Dip Process for Corrugated Steel Pipe
ASTM A 787/A787M : 2020 : REV A Standard Specification for Electric-Resistance-Welded Metallic-Coated Carbon Steel Mechanical Tubing
ASTM A 1063/A1063M : 2021 Standard Specification for Steel Sheet, Twin-Roll Cast, Zinc-Coated (Galvanized) by the Hot-Dip Process
ASTM A 1030/A1030M : 2021 Standard Practice for Measuring Flatness Characteristics of Steel Sheet Products
ASTM A 1087/A1087M : 2021 Standard Practice for Using Hand Calipers to Measure the Width of Steel Sheet
ASTM A 1073/A1073M : 2021 Standard Practice for Using Hand Micrometers to Measure the Thickness of Uncoated Steel Sheet and Nonmetallic and Metallic-Coated Steel Sheet
ASTM A 754/A754M : 2021 Standard Test Method for Coating Weight [Mass] of Metallic Coatings on Steel by X-Ray Fluorescence
ASTM A 792/A792M : 2021 : REV A Standard Specification for Steel Sheet, 55 % Aluminum-Zinc Alloy-Coated by the Hot-Dip Process
ASTM A 875/A875M : 2021 Standard Specification for Steel Sheet, Zinc-5 % Aluminum Alloy-Coated by the Hot-Dip Process
ASTM A 1079 : 2017 Standard Specification for Steel Sheet, Complex Phase (CP), Dual Phase (DP) and Transformation Induced Plasticity (TRIP), Zinc-Coated (Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed) by the Hot-Dip Process
ASTM A 1003/A1003M : 2015 Standard Specification for Steel Sheet, Carbon, Metallic- and Nonmetallic-Coated for Cold-Formed Framing Members

ASTM A 875/A875M : 2013 Standard Specification for Steel Sheet, Zinc-5 % Aluminum Alloy-Coated by the Hot-Dip Process
ASTM A 370 : 2021 Standard Test Methods and Definitions for Mechanical Testing of Steel Products
ASTM A 653/A653M : 2001 : REV A Standard Specification for Steel Sheet, Zinc-Coated (Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed) by the Hot-Dip Process
ASTM A 1063/A1063M : 2021 Standard Specification for Steel Sheet, Twin-Roll Cast, Zinc-Coated (Galvanized) by the Hot-Dip Process
ASTM A 90/A90M : 2021 Standard Test Method for Weight [Mass] of Coating on Iron and Steel Articles with Zinc or Zinc-Alloy Coatings
ASTM A 428/A428M : 2010 : R2019 Standard Test Method for Weight [Mass] of Coating on Aluminum-Coated Iron or Steel Articles
ASTM A 90/A90M : 2013 : R2018 Standard Test Method for Weight [Mass] of Coating on Iron and Steel Articles with Zinc or Zinc-Alloy Coatings
ASTM A 463/A463M : 2015 : R2020 : EDT 1 Standard Specification for Steel Sheet, Aluminum-Coated, by the Hot-Dip Process
ASTM E 29 : 2002 Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
ASTM A 1057/A1057M : 2008 : R2019 Standard Specification for Steel, Structural Tubing, Cold Formed, Welded, Carbon, Zinc-Coated (Galvanized) by the Hot-Dip Process
ASTM A 1073/A1073M : 2017 Standard Practice for Using Hand Micrometers to Measure the Thickness of Uncoated Steel Sheet and Nonmetallic and Metallic-Coated Steel Sheet
ASTM A 792/A792M : 2009 Standard Specification for Steel Sheet, 55 % Aluminum-Zinc Alloy-Coated by the Hot-Dip Process
ASTM A 653/A653M : 2020 Standard Specification for Steel Sheet, Zinc-Coated (Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed) by the Hot-Dip Process
ASTM A 1063/A1063M : 2020 Standard Specification for Steel Sheet, Twin-Roll Cast, Zinc-Coated (Galvanized) by the Hot-Dip Process
ASTM A 875/A875M : 2013 : R2021 Standard Specification for Steel Sheet, Zinc-5 % Aluminum Alloy-Coated by the Hot-Dip Process
ASTM A 929/A929M : 2018 Standard Specification for Steel Sheet, Metallic-Coated by the Hot-Dip Process for Corrugated Steel Pipe
ASTM A 1087/A1087M : 2016 Standard Practice for Using Hand Calipers to Measure the Width of Steel Sheet
ASTM A 754/A754M : 2018 Standard Test Method for Coating Weight (Mass) of Metallic Coatings on Steel by X-Ray Fluorescence
ASTM A 751 : 2021 Standard Test Methods and Practices for Chemical Analysis of Steel Products
ASTM A 370 : 2020 Standard Test Methods and Definitions for Mechanical Testing of Steel Products
ASTM A 1030/A1030M : 2021 Standard Practice for Measuring Flatness Characteristics of Steel Sheet Products
ASTM A 755/A755M : 2018 Standard Specification for Steel Sheet, Metallic Coated by the Hot-Dip Process and Prepainted by the Coil-Coating Process for Exterior Exposed Building Products
ASTM A 1073/A1073M : 2021 Standard Practice for Using Hand Micrometers to Measure the Thickness of Uncoated Steel Sheet and Nonmetallic and Metallic-Coated Steel Sheet
ASTM A 751 : 2020 Standard Test Methods and Practices for Chemical Analysis of Steel Products
ASTM A 370 : 2011 Standard Test Methods and Definitions for Mechanical Testing of Steel Products
ASTM A 792/A792M : 2010 : R2015 Standard Specification for Steel Sheet, 55 % Aluminum-Zinc Alloy-Coated by the Hot-Dip Process
ASTM A 1087/A1087M : 2021 Standard Practice for Using Hand Calipers to Measure the Width of Steel Sheet
ASTM A 428/A428M : 2021 Standard Test Method for Weight [Mass] of Coating on Aluminum-Coated Iron or Steel Articles
ASTM A 875/A875M : 2021 Standard Specification for Steel Sheet, Zinc-5 % Aluminum Alloy-Coated by the Hot-Dip Process
ASTM A 792/A792M : 2021 : REV A Standard Specification for Steel Sheet, 55 % Aluminum-Zinc Alloy-Coated by the Hot-Dip Process
ASTM A 754/A754M : 2021 Standard Test Method for Coating Weight [Mass] of Metallic Coatings on Steel by X-Ray Fluorescence
ASTM A 875/A875M : 2009 Standard Specification for Steel Sheet, Zinc-5 % Aluminum Alloy-Coated by the Hot-Dip Process
ASTM A 792/A792M : 2021 Standard Specification for Steel Sheet, 55 % Aluminum-Zinc Alloy-Coated by the Hot-Dip Process
ASTM A 929/A929M : 1997 Standard Specification for Steel Sheet, Metallic-Coated by the Hot-Dip Process for Corrugated Steel Pipe
ASTM A 1046/A1046M : 2019 Standard Specification for Steel Sheet, Zinc-Aluminum-Magnesium Alloy-Coated by the Hot-Dip Process
ASTM A 1030/A1030M : 2016 Standard Practice for Measuring Flatness Characteristics of Steel Sheet Products

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.