ASTM A 988/A988M : 2017 : REDLINE
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Hot Isostatically-Pressed Stainless Steel Flanges, Fittings, Valves, and Parts for High Temperature Service
25-05-2023
English
17-05-2017
CONTAINED IN VOL. 01.01, 2017 Defines hot isostatically-pressed, powder metallurgy, stainless steel piping components for use in pressure systems.
Committee |
A 01
|
DevelopmentNote |
Supersedes ASTM A 988. (09/2004)
|
DocumentType |
Redline
|
Pages |
13
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy |
1.1This specification covers hot isostatically-pressed, powder metallurgy, stainless steel piping components for use in pressure systems. Included are flanges, fittings, valves, and similar parts made to specified dimensions or to dimensional standards, such as in ASME specification B16.5.
1.2Several grades of martensitic, austenitic, age hardening, and austenitic-ferritic stainless steels are included in this specification.
1.3Supplementary requirements are provided for use when additional testing or inspection is desired. These shall apply only when specified individually by the purchaser in the order.
1.4This specification is expressed in both inch-pound units and in SI units. Unless the order specifies the applicable “M” specification designation (SI units), however, the material shall be furnished to inch-pound units.
1.5The values stated in either inch-pound units or SI units are to be regarded separately as the standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.6The following safety hazards caveat pertains only to test methods portions 8.1, 8.2, 9.5 – 9.7, and Section 10 of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
1.7This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
I.S. EN ISO 13628-15:2011 | PETROLEUM AND NATURAL GAS INDUSTRIES - DESIGN AND OPERATION OF SUBSEA PRODUCTION SYSTEMS - PART 15: SUBSEA STRUCTURES AND MANIFOLDS (ISO 13628-15:2011) |
UNI EN ISO 13628-15 : 2011 | PETROLEUM AND NATURAL GAS INDUSTRIES - DESIGN AND OPERATION OF SUBSEA PRODUCTION SYSTEMS - PART 15: SUBSEA STRUCTURES AND MANIFOLDS |
BS EN ISO 13628-15:2011 | Petroleum and natural gas industries. Design and operation of subsea production systems Subsea structures and manifolds |
AWS G2.3M/G2.3 : 2012 | GUIDE FOR THE JOINING OF SOLID SOLUTION AUSTENITIC STAINLESS STEELS |
NACE SP 04 99 : 2012 | CORROSION CONTROL AND MONITORING IN SEAWATER INJECTION SYSTEMS |
API 17P : 2013 | DESIGN AND OPERATION OF SUBSEA PRODUCTION SYSTEMS - SUBSEA STRUCTURES AND MANIFOLDS |
ISO 13628-15:2011 | Petroleum and natural gas industries — Design and operation of subsea production systems — Part 15: Subsea structures and manifolds |
EN ISO 13628-15:2011 | Petroleum and natural gas industries - Design and operation of subsea production systems - Part 15: Subsea structures and manifolds (ISO 13628-15:2011) |
AWS A5.14/A5.14M : 2011 | SPECIFICATION FOR NICKEL AND NICKEL-ALLOY BARE WELDING ELECTRODES AND RODS |
ASTM A 262 : 2015 : REDLINE | Standard Practices for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels |
ASTM A 923 : 2014 : REDLINE | Standard Test Methods for Detecting Detrimental Intermetallic Phase in Duplex Austenitic/Ferritic Stainless Steels |
ASTM B 311 : 2017 : REDLINE | Standard Test Method for Density of Powder Metallurgy (PM) Materials Containing Less Than Two Percent Porosity |
ASTM E 340 : 2015 : REDLINE | Standard Practice for Macroetching Metals and Alloys |
ASTM E 606/E606M : 2012 : REDLINE | Standard Test Method for Strain-Controlled Fatigue Testing |
ASTM A 745/A745M : 2015 : REDLINE | Standard Practice for Ultrasonic Examination of Austenitic Steel Forgings |
MSS SP 25 : 2013 | STANDARD MARKING SYSTEM FOR VALVES, FITTINGS, FLANGES, AND UNIONS |
AWS A5.11/A5.11M : 2010 | SPECIFICATION FOR NICKEL AND NICKEL-ALLOY WELDING ELECTRODES FOR SHIELDED METAL ARC WELDING |
ASME B16.5 : 2017 | PIPE FLANGES AND FLANGED FITTINGS: NPS 1/2 THROUGH NPS 24 METRIC/INCH STANDARD |
ASTM A 275/A275M : 2015-05 | PRACTICE FOR MAGNETIC PARTICLE EXAMINATION OF STEEL FORGINGS |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.