• Shopping Cart
    There are no items in your cart

ASTM B 103/B103M : 2019

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by

Standard Specification for Phosphor Bronze Plate, Sheet, Strip, and Rolled Bar

Available format(s)

Hardcopy , PDF

Superseded date

19-10-2023

Superseded by

ASTM B 103/B103M : 2023

Language(s)

English

Published date

28-10-2019

€67.30
Excluding VAT

Committee
B 05
DocumentType
Standard
Pages
7
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

1.1This specification establishes the requirements for copper-tin alloy (phosphor bronze), copper-tin-lead alloy (leaded phosphor bronze), and copper-tin-lead-zinc alloy (bearing bronze), plate, sheet, strip, and rolled bar. The phosphor bronzes commonly are used for deep drawing into bellows and stamping and forming into spring devices and into terminals and connectors for electrical apparatus because they combine high strength with high elongation. The leaded phosphor bronzes are used where strength, corrosion resistance, and machinability are required. The bearing bronze is used in bushings, bearings, and load-bearing thrust washers. The following alloys are covered:

Copper Alloy UNS No.2

Nominal Composition, %

Previously Used Designation

Copper

Tin

Zinc

Lead

C51000

95

5

. . .

. . .

A1

C51100

96

4

. . .

. . .

A 

C51180

96

4

. . .

. . .

. . .

C51900

94

6

. . .

. . .

 C52100A

92

8

. . .

. . .

C 

C52180

92

8

. . .

. . .

. . .

C52400

90

10 

. . .

. . .

D 

C53400

94

5

. . .

1

B1

C54400

88

4

3

4

B2


Note 1:All of the above alloys contain small amounts of phosphorus, used as a deoxidant in melting, and to enhance the mechanical properties.

1.2The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, SI units are shown in brackets. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.

1.3The following safety hazard caveat pertains only to the test method(s) described in this specification.

1.3.1This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ASTM F 1182 : 2007 : R2023 Standard Specification for Anodes, Sacrificial Zinc Alloy
ASTM E 18 : 2022 Standard Test Methods for Rockwell Hardness of Metallic Materials
ASTM F 375 : 2020 Standard Specification for Integrated Circuit Lead Frame Material (Withdrawn 2023)

ASTM B 248M : 2022 Standard Specification for General Requirements for Wrought Copper and Copper-Alloy Plate, Sheet, Strip, and Rolled Bar (Metric)
ASTM E 255 : 2023 Standard Practice for Sampling Copper and Copper Alloys for the Determination of Chemical Composition
ASTM E 8/E8M : 2016 : REV A : EDT 1 Standard Test Methods for Tension Testing of Metallic Materials
ASTM E 8/E8M : 2021 Standard Test Methods for Tension Testing of Metallic Materials
ASTM E 255 : 1991 : R1997 Standard Practice for Sampling Copper and Copper Alloys for the Determination of Chemical Composition
ASTM E 527 : 2023 Standard Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS)
ASTM E 527 : 2016 Standard Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS)
ASTM E 8/E8M : 2022 Standard Test Methods for Tension Testing of Metallic Materials
ASTM B 248 : 2017 Standard Specification for General Requirements for Wrought Copper and Copper-Alloy Plate, Sheet, Strip, and Rolled Bar
ASTM B 248M : 2017 Standard Specification for General Requirements for Wrought Copper and Copper-Alloy Plate, Sheet, Strip, and Rolled Bar (Metric)
ASTM E 478 : 2008 : R2017 Standard Test Methods for Chemical Analysis of Copper Alloys
ASTM B 248 : 2022 Standard Specification for General Requirements for Wrought Copper and Copper-Alloy Plate, Sheet, Strip, and Rolled Bar
ASTM E 255 : 2007 : R2014 Standard Practice for Sampling Copper and Copper Alloys for the Determination of Chemical Composition (Withdrawn 2023)

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.