ASTM B 103/B103M : 2023
Current
The latest, up-to-date edition.
Standard Specification for Phosphor Bronze Plate, Sheet, Strip, and Rolled Bar
Hardcopy , PDF
English
11-10-2023
Committee |
B 05
|
DocumentType |
Standard
|
Pages |
6
|
PublisherName |
American Society for Testing and Materials
|
Status |
Current
|
Supersedes |
1.1This specification covers the requirements for copper-tin alloy (phosphor bronze), copper-tin-lead alloy (leaded phosphor bronze), and copper-tin-lead-zinc alloy (bearing bronze), plate, sheet, strip, and rolled bar for general application produced from Copper Alloy UNS Nos. C51000, C51100, C51180, C51900, C52100, C52180, C52400, C53400, and C54400. The phosphor bronzes commonly are used for deep drawing into bellows and stamping and forming into spring devices and into terminals and connectors for electrical apparatus because they combine high strength with high elongation. The leaded phosphor bronzes are used where strength, corrosion resistance, and machinability are required. The bearing bronze is used in bushings, bearings, and load-bearing thrust washers.
Note 1:All of the above alloys contain small amounts of phosphorus, used as a deoxidant in melting, and to enhance the mechanical properties.
1.2Units—The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, SI units are shown in brackets. The values stated in each system are not necessarily exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.3The following safety hazard caveat pertains only to the test method(s) described in this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM F 1182 : 2007 : R2023 | Standard Specification for Anodes, Sacrificial Zinc Alloy |
ASTM E 18 : 2022 | Standard Test Methods for Rockwell Hardness of Metallic Materials |
ASTM F 375 : 2020 | Standard Specification for Integrated Circuit Lead Frame Material (Withdrawn 2023) |
ASTM B 248M : 2022 | Standard Specification for General Requirements for Wrought Copper and Copper-Alloy Plate, Sheet, Strip, and Rolled Bar (Metric) |
ASTM B 248 : 2022 | Standard Specification for General Requirements for Wrought Copper and Copper-Alloy Plate, Sheet, Strip, and Rolled Bar |
ASTM E 8/E8M : 2024 | Standard Test Methods for Tension Testing of Metallic Materials |
ASTM B 846 : 2019 : REV A | Standard Terminology for Copper and Copper Alloys |
ASTM E 478 : 2024 | Standard Test Methods for Chemical Analysis of Copper Alloys |
ASTM B 846 : 2024 | Standard Terminology for Copper and Copper Alloys |
ASTM E 8/E8M : 2022 | Standard Test Methods for Tension Testing of Metallic Materials |
ASTM E 478 : 2008 : R2017 | Standard Test Methods for Chemical Analysis of Copper Alloys |
ASTM B 601 : 2024 | Standard Classification for Temper Designations for Copper and Copper Alloys—Wrought and Cast |
ASTM B 601 : 2018 : REV A | Standard Classification for Temper Designations for Copper and Copper Alloys—Wrought and Cast |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.