ASTM B 153 : 2011 : R2017
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Expansion (Pin Test) of Copper and Copper-Alloy Pipe and Tubing
Hardcopy , PDF
18-06-2022
English
13-04-2017
CONTAINED IN VOL. 02.01, 2017 Describes the requirements for the expansion pin test for copper and copper-alloy pipe and tubing with an inside diameter of 0.125 in. (3.2 mm) and greater or an outside diameter up to and including 4 in. (102 mm).
Committee |
B 05
|
DocumentType |
Test Method
|
Pages |
2
|
ProductNote |
Reconfirmed 2017
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
1.1This test method establishes the requirements for the expansion pin test for copper and copper-alloy pipe and tubing with an inside diameter of 0.125 in. (3.2 mm) and greater or an outside diameter up to and including 4 in. (102 mm).
Note 1:For tubes of sizes with an inside diameter less than 0.125 in. (3.2 mm), a substitute test method must be agreed upon between the manufacturer and purchaser.
Note 2:For tubes of sizes greater than 4 in. (102 mm) in outside diameter, refer to B968/B968M for a test method.
1.2Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM B 903 : 2015 : R2022 | Standard Specification for Seamless Copper Heat Exchanger Tubes With Internal Enhancement |
ASTM B 968/B968M : 2016 : R2022 | Standard Test Method for Flattening of Copper and Copper-Alloy Pipe and Tube |
ASTM B 944 : 2011 : R2016 | Standard Specification for Copper-Beryllium Welded Heat Exchanger and Condenser Tube (UNS No. C17510) |
ASTM B 543/B543M : 2018 | Standard Specification for Welded Copper and Copper-Alloy Heat Exchanger Tube |
ASTM B 359/B359M : 2018 | Standard Specification for Copper and Copper-Alloy Seamless Condenser and Heat Exchanger Tubes With Integral Fins |
ASTM B 68/B68M : 2019 | Standard Specification for Seamless Copper Tube, Bright Annealed |
ASTM B 587 : 2019 | Standard Specification for Welded Brass Tube |
ASTM B 552 : 2019 | Standard Specification for Seamless and Welded Copper–Nickel Tubes for Water Desalting Plants |
ASTM B 919 : 2019 | Standard Specification for Welded Copper Heat Exchanger Tubes With Internal Enhancement |
ASTM B 111/B111M : 2018 : REV A | Standard Specification for Copper and Copper-Alloy Seamless Condenser Tubes and Ferrule Stock |
ASTM B 956 : 2019 : EDT 1 | Standard Specification for Welded Copper and Copper-Alloy Condenser and Heat Exchanger Tubes with Integral Fins |
ASTM B 837 : 2019 | Standard Specification for Seamless Copper Tube for Natural Gas and Liquified Petroleum (LP) Gas Fuel Distribution Systems |
ASTM B 280 : 2020 | Standard Specification for Seamless Copper Tube for Air Conditioning and Refrigeration Field Service |
ASTM B 43 : 2020 | Standard Specification for Seamless Red Brass Pipe, Standard Sizes |
ASTM B 42 : 2020 | Standard Specification for Seamless Copper Pipe, Standard Sizes |
ASTM B 75/B75M : 2020 | Standard Specification for Seamless Copper Tube |
ASTM B 88M : 2020 | Standard Specification for Seamless Copper Water Tube (Metric) |
ASTM B 88 : 2020 | Standard Specification for Seamless Copper Water Tube |
ASTM B 466/B466M : 2018 | Standard Specification for Seamless Copper-Nickel Pipe and Tube |
ASTM B 743 : 2012 : R2020 | Standard Specification for Seamless Copper Tube in Coils |
ASTM B 1014 : 2020 | Standard Specification for Welded Copper and Copper Alloy Condenser and Heat Exchanger Tubes with a Textured Surface(s) |
ASTM B 640 : 2012 : REV A : R2021 | Standard Specification for Welded Copper Tube for Air Conditioning and Refrigeration Service |
ASTM B 447 : 2012 : REV A : R2021 | Standard Specification for Welded Copper Tube |
ASTM B 1017 : 2021 | Standard Specification for Seamless Copper-Iron Tube for Air Conditioning and Refrigeration |
ASTM B 1018 : 2021 | Standard Specification for Seamless Copper-Iron Tube for Air Conditioning and Refrigeration Field Service |
ASTM B 950 : 2021 : EDT 1 | Standard Guide for Editorial Procedures and Form of Product Specifications for Copper and Copper Alloys |
ASTM B 395/B395M : 2018 | Standard Specification for U-Bend Seamless Copper and Copper Alloy Heat Exchanger and Condenser Tubes |
ASTM B 467 : 2014 | Standard Specification for Welded Copper-Nickel Pipe |
ASTM B 1003 : 2016 | Standard Specification for Seamless Copper Tube for Linesets |
ASTM B 135/B135M : 2017 | Standard Specification for Seamless Brass Tube |
ASTM B 251/B251M : 2017 | Standard Specification for General Requirements for Wrought Seamless Copper and Copper-Alloy Tube |
ASTM B 968/B968M : 2016 | Standard Test Method for Flattening of Copper and Copper-Alloy Pipe and Tube |
ASTM B 968/B968M : 2016 : REDLINE | Standard Test Method for Flattening of Copper and Copper-Alloy Pipe and Tube |
ASTM B 846 : 2011-07 | TERMINOLOGY FOR COPPER AND COPPER ALLOYS |
ASTM B 968/B968M : 2016 : R2022 | Standard Test Method for Flattening of Copper and Copper-Alloy Pipe and Tube |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.