• There are no items in your cart

ASTM B 16/B16M : 2024

Current

Current

The latest, up-to-date edition.

Standard Specification for Free-Cutting Brass Rod, Bar and Shapes for Use in Screw Machines

Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

01-07-2024

€56.53
Excluding VAT

Committee
B 05
DocumentType
Standard
Pages
5
PublisherName
American Society for Testing and Materials
Status
Current
Supersedes

1.1This specification covers the requirements for free-cutting brass rod, bar, wire, and shapes of any specified cross section produced from Copper Alloy UNS Nos. C36000 or C36010 suitable for high-speed screw machining applications and moderate thread rolling.

1.2Units—Values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, SI units are shown in brackets. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other and values from the two systems shall not be combined.

1.3The following safety hazard caveat pertains only to the test method(s) described in this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ASTM D 2625 : 2020 Standard Test Method for Endurance (Wear) Life and Load-Carrying Capacity of Solid Film Lubricants (Falex Pin and Vee Method)
ASTM D 3233 : 2019 Standard Test Methods for Measurement of Extreme Pressure Properties of Fluid Lubricants (Falex Pin and Vee Block Methods)
ASTM F 3226/F3226M : 2019 : REDLINE Standard Specification for Metallic Press-Connect Fittings for Piping and Tubing Systems
ASTM B 453/B453M : 2019 Standard Specification for Copper-Zinc-Lead Alloy (Leaded-Brass) Rod, Bar, and Shapes
ASTM F 3347 : 2023 Standard Specification for Metal Press Insert Fittings with Factory Assembled Stainless Steel Press Sleeve for SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Polyethylene of Raised Temperature (PE-RT) Tubing
ASTM F 2080 : 2023 Standard Specification for Cold-Expansion Fittings with Metal Compression-Sleeves for Crosslinked Polyethylene (PEX) Pipe and SDR9 Polyethylene of Raised Temperature (PE-RT) Pipe
ASTM D 950 : 2003 : R2020 : EDT 1 Standard Test Method for Impact Strength of Adhesive Bonds
ASTM F 1960 : 2023 : REV B Standard Specification for Cold Expansion Fittings with PEX Reinforcing Rings for Use with Cross-linked Polyethylene (PEX) and Polyethylene of Raised Temperature (PE-RT) Tubing
ASTM F 2854 : 2021 Standard Specification for Push-Fit Crosslinked Polyethylene (PEX) Mechanical Fittings for Crosslinked Polyethylene (PEX) Tubing
ASTM F 1807 : 2023 Standard Specification for Metal Insert Fittings Utilizing a Copper Crimp Ring, or Alternate Stainless Steel Clamps, for SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Polyethylene of Raised Temperature (PE-RT) Tubing
ASTM F 2929 : 2017 : R2021 Standard Specification for Crosslinked Polyethylene (PEX) Tubing of 0.070 in. Wall and Fittings for Radiant Heating Systems up to 75 psig
ASTM B 927/B927M : 2023 Standard Specification for Brass Rod, Bar, and Shapes
ASTM D 2670 : 2020 Standard Test Method for Measuring Wear Properties of Fluid Lubricants (Falex Pin and Vee Block Method)
ASTM B 249/B249M : 2023 Standard Specification for General Requirements for Wrought Copper and Copper-Alloy Rod, Bar, Shapes and Forgings
ASTM D 897 : 2008 : R2016 Standard Test Method for Tensile Properties of Adhesive Bonds
ASTM F 1974 : 2023 Standard Specification for Metal Insert Fittings for Polyethylene/Aluminum/Polyethylene and Crosslinked Polyethylene/Aluminum/Crosslinked Polyethylene Composite Pressure Pipe
ASTM B 250/B250M : 2019 Standard Specification for General Requirements for Wrought Copper Alloy Wire
ASTM F 721 : 2018 : R2022 Standard Specification for Gauge Piping Assemblies
ASTM F 1387 : 2023 Standard Specification for Performance of Piping and Tubing Mechanically Attached Fittings
ASTM D 1062 : 2008 : R2023 Standard Test Method for Cleavage Strength of Metal-to-Metal Adhesive Bonds
ASTM F 826 : 2022 Standard Specification for Tops, Furniture, Marine, Steel

ASTM B 846 : 2019 : REV A Standard Terminology for Copper and Copper Alloys
ASTM E 478 : 2024 Standard Test Methods for Chemical Analysis of Copper Alloys
ASTM B 846 : 2024 Standard Terminology for Copper and Copper Alloys
ASTM E 478 : 2008 : R2017 Standard Test Methods for Chemical Analysis of Copper Alloys

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.