ASTM B 209/B209M : 2021
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate
Hardcopy , PDF
04-09-2024
English
16-06-2021
Important note : Users cannot be edited or removed once added to your Multi user PDF.| Committee |
B 07
|
| DocumentType |
Standard
|
| Pages |
41
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This specification2 covers aluminum and aluminum-alloy flat sheet, coiled sheet, and plate in the alloys (Note 1) and tempers shown in Tables 2, 3, 4, and 5, and in the following finishes:
1.1.1Plate in all alloys and sheet in heat-treatable alloys: mill finish.
1.1.2Sheet in nonheat-treatable alloys: mill finish, one-side bright mill finish, standard one-side bright finish, and standard two-sides bright finish.
1.2Alloy and temper designations are in accordance with ANSI H35.1/H35.1M. The equivalent Unified Numbering System alloy designations are those of Table 1 preceded by A9, for example, A91100 for aluminum 1100 in accordance with Practice E527.
Note 1:Throughout this specification, use of the term alloy in the general sense includes aluminum as well as aluminum alloy.
Note 2:See Specification B632/B632M for tread plate.
Note 3:See Specification B928/B928M for 5xxx-H116 and 5xxx-H321 aluminum alloys containing 3 % or more nominal magnesium and intended for marine service and similar environments. Other alloy-temper products listed in this specification, which do not require the additional corrosion testing/capability called out in Specification B928/B928M, may be suitable for marine and similar environment applications.
1.3For acceptance criteria for inclusion of new aluminum and aluminum alloys in this specification, see Annex A2.
1.4The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.
1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASME A112.36.2/CSA B79.2:2022 | Cleanouts |
| ASTM F 683 : 2021 | Standard Practice for Selection and Application of Thermal Insulation for Piping and Machinery |
| ASTM E 1800 : 2021 | Standard Specification for Adhesive for Bonding Foam Cored Sandwich Panels (160 °F Elevated Humidity Service), Type I Panels |
| ASTM D 8379/D8379M : 2021 | Standard Practice for Evaluating Nighttime Retroreflective Sheeting Effectiveness Using Positive-Contrast Textual Sign Scenario Performance Analysis |
| ASTM B 660 : 2021 | Standard Practices for Packaging/Packing of Aluminum and Magnesium Products |
| ASTM E 716 : 2016 : R2021 | Standard Practices for Sampling and Sample Preparation of Aluminum and Aluminum Alloys for Determination of Chemical Composition by Spark Atomic Emission Spectrometry |
| ASTM E 716 : 2016 | Standard Practices for Sampling and Sample Preparation of Aluminum and Aluminum Alloys for Determination of Chemical Composition by Spark Atomic Emission Spectrometry |
| ASTM B 660 : 2015 | Standard Practices for Packaging/Packing of Aluminum and Magnesium Products |
| ASTM E 716 : 2016 : R2021 : EDT 1 | Standard Practices for Sampling and Sample Preparation of Aluminum and Aluminum Alloys for Determination of Chemical Composition by Spark Atomic Emission Spectrometry |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.