Skip to content
Please enter a keyword to search

  • ASTM B 306 : 2013 : REDLINE

    View superseded by
    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    View superseded by

    Standard Specification for Copper Drainage Tube (DWV)

    Available format(s):  PDF

    Superseded date:  10-08-2020

    Language(s):  English

    Published date:  01-04-2013

    Publisher:  American Society for Testing and Materials

    Add To Cart

    Abstract - (Show below) - (Hide below)

    CONTAINED IN VOL. 02.01, 2017 Describes the requirements for seamless copper tube (DWV) produced from Copper UNS No. C12200 and intended for sanitary drainage, waste, and vent piping.

    Scope - (Show below) - (Hide below)

    1.1This specification establishes the requirements for seamless copper tube (DWV) produced from Copper UNS No. C12200 and intended for sanitary drainage, waste, and vent piping.

    Note 1—Fittings used for soldered or brazed connections in drainage, waste, or vent systems are described in ASME Standards B16.23 and B16.29 and CSA Standard B158.1.
    Note 2—The assembly of copper drainage, waste, and vent systems by soldering is described in Practice B828.
    Note 3—Solders for joining copper drainage, waste, or vent systems are described in Specification B32. The requirement for acceptable fluxes for these systems are described in Specification B813.

    1.2The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

    1.3The following hazard statement pertains only to the test method described in Section 16.2.3 of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

    General Product Information - (Show below) - (Hide below)

    Committee B 05
    Document Type Redline
    Publisher American Society for Testing and Materials
    Status Superseded
    Superseded By

    Standards Referenced By This Book - (Show below) - (Hide below)

    ICC 2009 INT. RESI.CODE & COMM.-I1 : 2009 2009 INTERNATIONAL RESIDENTIAL CODE & COMMENTARY - VOLUME 2: CHAPTERS 12 TO 44
    ASME B16.29 : 2017 Wrought Copper and Wrought Copper Alloy Solder-Joint Drainage Fittings--DWV
    CSA Z662 PACKAGE : 2011 CONSISTS OF Z662-11, OIL AND GAS PIPELINE SYSTEMS AND Z662.1-11, COMMENTARY ON CSA Z662-11, OIL AND GAS PIPELINE SYSTEMS
    ICC IPC CODE & COMMENTARY : 2015 IPC® Code and Commentary
    NASA SSTD 8070 0125 : 2015 PROCEDURE FOR WELDING COPPER TUBE
    ICC IRC CODE AND COMMENTARY VOLUME 2 : 2015 IRC® Code and Commentary, Volume 2
    ICC 2012 INTERNATIONAL RESI. CODE : 2012 INTERNATIONAL RESIDENTIAL CODE FOR ONE- AND TWO-FAMILY DWELLINGS
    ICC 2012 INTERNATIONAL PLUMBING CODE : 2012 INTERNATIONAL PLUMBING CODE (INCLUDES IPSDC)
    ASTM B 698/B698M : 2010 : R2016 : EDT 1 Standard Classification for Seamless Copper and Copper Alloy Plumbing Pipe and Tube
    MIL-HDBK-270 Revision A:1991 METALLIC MATERIALS FOR LOW MAGNETIC APPLICATIONS, MAGNETIC PERMEABILITY AND ELECTRICAL CONDUCTIVITY, CHARACTERISTICS OF (METRIC)
    CSA B242 : 2005 GROOVE- AND SHOULDER-TYPE MECHANICAL PIPE COUPLINGS
    CSA B602 : 2016 MECHANICAL COUPLINGS FOR DRAIN, WASTE, AND VENT PIPE AND SEWER PIPE
    CSA B55.2 : 2015 DRAIN WATER HEAT RECOVERY UNITS
    ASTM B 828 : 2016 : REDLINE Standard Practice for Making Capillary Joints by Soldering of Copper and Copper Alloy Tube and Fittings
    CSA B242 : 2005 : R2016 GROOVE- AND SHOULDER-TYPE MECHANICAL PIPE COUPLINGS
    ASME B16.23 : 2016 CAST COPPER ALLOY SOLDER JOINT DRAINAGE FITTINGS: DWV

    Standards Referencing This Book - (Show below) - (Hide below)

    ASTM B 900 : 2016 : REDLINE Standard Practice for Packaging of Copper and Copper Alloy Mill Products for U.S. Government Agencies
    ASME B16.23 : 2016 CAST COPPER ALLOY SOLDER JOINT DRAINAGE FITTINGS: DWV
    CSA B158.1 : 76(R1992) CAST BRASS SOLDER JOINT DRAINAGE, WASTE AND VENT FITTINGS
    ASTM E 527 : 2016 : REDLINE Standard Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS)
    ASTM B 828 : 2016 : REDLINE Standard Practice for Making Capillary Joints by Soldering of Copper and Copper Alloy Tube and Fittings
    ASTM E 8 : 2004 Standard Test Methods for Tension Testing of Metallic Materials
    ASME B16.29 : 2012 WROUGHT COPPER AND WROUGHT COPPER ALLOY SOLDER-JOINT DRAINAGE FITTINGS - DWV
    ASTM B 813 : 2016 : REDLINE Standard Specification for Liquid and Paste Fluxes for Soldering of Copper and Copper Alloy Tube
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective