ASTM B 316/B316M : 2015 : REDLINE
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Aluminum and Aluminum-Alloy Rivet and Cold-Heading Wire and Rods
16-01-2021
English
01-10-2015
Important note : Users cannot be edited or removed once added to your Multi user PDF.CONTAINED IN VOL. 02.02, 2017 Defines wire and rod in the alloys, suitable for manufacturing rivets and other similar items by cold-heading operations.
| Committee |
B 07
|
| DevelopmentNote |
Supersedes ASTM B316M and ASTM B 316. (12/2001)
|
| DocumentType |
Redline
|
| Pages |
9
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy |
1.1This specification covers wire and rod in the alloys (Note 1) shown in Table 1 and the tempers shown in Table 2 [Table 3] and Table 4 [Table 5], suitable for manufacturing rivets and other similar items by cold-heading operations.
Note 1:Throughout this specification the use of the term alloy in the general sense includes aluminum as well as aluminum alloy.
Note 2:For rolled or cold-finished wire and rod, see Specification B211, and for extruded wire and rod, see Specification B221.
1.2Alloy and temper designations are in accordance with ANSI H35.1/H35.1M. The equivalent Unified Numbering System alloy designations are those of Table 1 preceded by A9, for example, A91100 for aluminum 1100 in accordance with Practice E527.
1.3For acceptance criteria for inclusion of new aluminum and aluminum alloys in this specification, see Annex A2.
1.4The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.4.1The SI units are shown either in brackets or in separate tables.
| ASTM C 1802 : 2014 | Standard Specification for Design, Testing, Manufacture, Selection, and Installation of Fabricated Metal Access Hatches for Utility, Water, and Wastewater Structures<rangeref></rangeref > |
| AASHTO LRFDLTS 1 : 1900 | LRFD SPECIFICATIONS FOR STRUCTURAL SUPPORTS FOR HIGHWAY SIGNS, LUMINAIRES, AND TRAFFIC SIGNALS |
| ASTM B 211M : 2012 : EDT 1 | Standard Specification for Aluminum and Aluminum-Alloy Rolled or Cold-Finished Bar, Rod, and Wire (Metric) (Withdrawn 2019) |
| ASTM B 211 : 2012 : EDT 1 | Standard Specification for Aluminum and Aluminum-Alloy Rolled or Cold Finished Bar, Rod, and Wire |
| ASTM B 211 : 2012 | Standard Specification for Aluminum and Aluminum-Alloy Rolled or Cold Finished Bar, Rod, and Wire |
| ASTM B 565 : 2004 : R2010 | Standard Test Method for Shear Testing of Aluminum and Aluminum-Alloy Rivets and Cold-Heading Wire and Rods |
| ASTM B 211M : 2012 | Standard Specification for Aluminum and Aluminum-Alloy Rolled or Cold-Finished Bar, Rod, and Wire (Metric) |
| ASTM B 565:2004 | Standard Test Method for Shear Testing of Aluminum and Aluminum-Alloy Rivets and Cold-Heading Wire and Rods |
| AASHTO M 196 : 1992 | SPECIFICATION FOR CORRUGATED ALUMINUM PIPE FOR SEWERS AND DRAINS |
| ASTM B 881 : 2017 : REDLINE | Standard Terminology Relating to Aluminum- and Magnesium-Alloy Products |
| PREN 2552 : 3 | AEROSPACE SERIES - RIVETS, SOLID, 100 DEGREES COUNTERSUNK NORMAL HEAD, WITH DOME, IN ALUMINIUM ALLOY 2117, ANODIZED OR CHROMATED, INCH BASED SERIES |
| PREN 2551 : 3 | Rivets, solid, 100° normal countersunk head with dome, in aluminium alloy 2117 - Inch based series |
| ASTM C 1802 : 2014 : EDT 1 | Standard Specification for Design, Testing, Manufacture, Selection, and Installation of Fabricated Metal Access Hatches for Utility, Water, and Wastewater Structures<rangeref></rangeref > |
| ASTM B 565 : 2004 : R2015 | Standard Test Method for Shear Testing of Aluminum and Aluminum-Alloy Rivets and Cold-Heading Wire and Rods |
| ASTM B 745/B745M : 2015 : REDLINE | Standard Specification for Corrugated Aluminum Pipe for Sewers and Drains |
| ASME B18.30.1M : 2000 : R2010 | OPEN-END BLIND RIVETS WITH BREAK MANDRELS (METRIC SERIES) |
| ASME B18.30.1M : 2000 : R2005 | OPEN-END BLIND RIVETS WITH BREAK MANDRELS (METRIC SERIES) |
| ANSI H35.2 : 2017 | DIMENSIONAL TOLERANCES FOR ALUMINUM MILL PRODUCTS |
| ANSI H35.1/H35.1M : 2017 | ALLOY AND TEMPER DESIGNATION SYSTEMS FOR ALUMINUM |
| MIL-STD-129 Revision R:2014 | Military Marking for Shipment and Storage |
| ASTM B 918 : 2001 | Standard Practice for Heat Treatment of Wrought Aluminum Alloys |
| ASTM E 607 : 2002 | Standard Test Method for Atomic Emission Spectrometric Analysis Aluminum Alloys by the Point to Plane Technique Nitrogen Atmosphere |
| ASTM B 666/B666M : 2015 : REDLINE | Standard Practice for Identification Marking of Aluminum and Magnesium Products |
| EN 14242:2004 | Aluminium and aluminium alloys - Chemical analysis - Inductively coupled plasma optical emission spectral analysis |
| ASTM B 221 : 2014 : REDLINE | Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes |
| ASTM B 557 : 2015 : REDLINE | Standard Test Methods for Tension Testing Wrought and Cast Aluminum- and Magnesium-Alloy Products |
| FED-STD-123 Revision H:2007 | MARKING FOR SHIPMENT (CIVIL AGENCIES) |
| SAE AMS2772G | Heat Treatment of Aluminum Alloy Raw Materials |
| ASTM E 716 : 2016 : REDLINE | Standard Practices for Sampling and Sample Preparation of Aluminum and Aluminum Alloys for Determination of Chemical Composition by Spark Atomic Emission Spectrometry |
| ASTM E 527 : 2016 : REDLINE | Standard Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS) |
| ASTM B 557M : 2015 : REDLINE | Standard Test Methods for Tension Testing Wrought and Cast Aluminum- and Magnesium-Alloy Products (Metric) |
| ASTM E 1004 : 2017 : REDLINE | Standard Test Method for Determining Electrical Conductivity Using the Electromagnetic (Eddy Current) Method |
| ASTM B 660 : 2015 : REDLINE | Standard Practices for Packaging/Packing of Aluminum and Magnesium Products |
| ANSI H35.2M : 2013 | DIMENSIONAL TOLERANCES FOR ALUMINUM MILL PRODUCTS (METRIC) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.