![header thumbnail](/images/publishers\astm_cover.gif)
ASTM B 317/B317M : 2007 : R2015 : EDT 1
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
![header thumbnail](/images/publishers\astm_cover.gif)
Standard Specification for Aluminum-Alloy Extruded Bar, Rod, Tube, Pipe, Structural Profiles, and Profiles for Electrical Purposes (Bus Conductor)
Hardcopy , PDF
17-12-2023
English
30-11-2016
CONTAINED IN VOL. 02.02, 2016 Defines 6101 aluminum-alloy extruded bar, rod, tube, pipe, (Schedules 40 and 80), structural profiles, and profiles in selected tempers for use as electric conductors.
Committee |
B 07
|
DevelopmentNote |
Supersedes ASTM B 317. (11/2004)
|
DocumentType |
Standard
|
Pages |
8
|
ProductNote |
Reconfirmed EDT 1
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
1.1This specification covers 6101 aluminum-alloy extruded bar, rod, tube, pipe, (Schedules 40 and 80), structural profiles, and profiles in selected tempers for use as electric conductors as follows:
1.1.1Type B—Hot-finished bar, rod, tube, pipe, structural profiles and profiles in T6, T61, T63, T64, T65, and H111 tempers with Type B tolerances, as shown in the “List of ANSI Tables of Dimensional Tolerances.”
1.1.2Type C—Hot-finished rectangular bar in T6, T61, T63, T64, T65, and H111 tempers with Type C tolerances as listed in the tolerances and permissible variations tables.
1.2Alloy and temper designations are in accordance with ANSI H35.1. The equivalent Unified Numbering System alloy designation in accordance with Practice E527 is A96101 for Alloy 6101.
Note 1:Type A material, last covered in the 1966 issue of this specification, is no longer available; therefore, requirements for cold-finished rectangular bar have been deleted.
1.3For acceptance criteria for inclusion of new aluminum and aluminum alloys in this specification, see Annex A2.
1.4The values stated in either SI or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
ASTM B 236 : 2007 : R2015 | Standard Specification for Aluminum Bars for Electrical Purposes (Bus Bars) |
ASTM B 881 : 2017 | Standard Terminology Relating to Aluminum- and Magnesium-Alloy Products |
ASTM B 236M : 2007 : R2015 | Standard Specification for Aluminum Bars for Electrical Purposes (Bus Bars) (Metric) (Withdrawn 2024) |
ANSI H35.2 : 2017 | DIMENSIONAL TOLERANCES FOR ALUMINUM MILL PRODUCTS |
ASTM B 807/B807M : 2013 : REDLINE | Standard Practice for Extrusion Press Solution Heat Treatment for Aluminum Alloys |
ASTM E 1251 : 2007 | Standard Test Method for Analysis of Aluminum and Aluminum Alloys by Atomic Emission Spectrometry |
ASTM B 557 : 2015 : R2023 | Standard Test Methods for Tension Testing Wrought and Cast Aluminum- and Magnesium-Alloy Products |
ANSI H35.1/H35.1M : 2017 | ALLOY AND TEMPER DESIGNATION SYSTEMS FOR ALUMINUM |
MIL-STD-129 Revision R:2014 | Military Marking for Shipment and Storage |
ASTM E 1004 : 2009 | Standard Test Method for Determining Electrical Conductivity Using the Electromagnetic (Eddy-Current) Method |
ASTM B 253 : 2011 : R2022 | Standard Guide for Preparation of Aluminum Alloys for Electroplating |
ASTM E 29 : 2013 : R2019 | Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications |
ASTM B 918 : 2001 | Standard Practice for Heat Treatment of Wrought Aluminum Alloys |
ASTM E 607 : 2002 | Standard Test Method for Atomic Emission Spectrometric Analysis Aluminum Alloys by the Point to Plane Technique Nitrogen Atmosphere |
ASTM B 666/B666M : 2015 : REDLINE | Standard Practice for Identification Marking of Aluminum and Magnesium Products |
ASTM E 1251 : 1994 : R1999 | Standard Test Method for Optical Emission Spectrometric Analysis of Aluminum and Aluminum Alloys by the Argon Atmosphere, Point-to-Plane, Unipolar Self-Initiating Capacitor Discharge |
ASTM E 716 : 2016 : R2021 : EDT 2 | Standard Practices for Sampling and Sample Preparation of Aluminum and Aluminum Alloys for Determination of Chemical Composition by Spark Atomic Emission Spectrometry |
ASTM E 29 : 2002 | Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications |
ASTM B 660 : 2021 | Standard Practices for Packaging/Packing of Aluminum and Magnesium Products |
ASTM E 1251 : 2017 | Standard Test Method for Analysis of Aluminum and Aluminum Alloys by Spark Atomic Emission Spectrometry |
ASTM E 716 : 2016 : R2021 | Standard Practices for Sampling and Sample Preparation of Aluminum and Aluminum Alloys for Determination of Chemical Composition by Spark Atomic Emission Spectrometry |
ASTM B 557 : 2015 : REDLINE | Standard Test Methods for Tension Testing Wrought and Cast Aluminum- and Magnesium-Alloy Products |
ASTM E 527 : 2023 | Standard Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS) |
ASTM E 1004 : 1999 | Standard Practice for Determining Electrical Conductivity Using the Electromagnetic (Eddy-Current) Method |
ASTM E 1004 : 2002 | Standard Practice for Determining Electrical Conductivity Using the Electromagnetic (Eddy-Current) Method |
ASTM E 716 : 2016 | Standard Practices for Sampling and Sample Preparation of Aluminum and Aluminum Alloys for Determination of Chemical Composition by Spark Atomic Emission Spectrometry |
ASTM B 557 : 2015 | Standard Test Methods for Tension Testing Wrought and Cast Aluminum- and Magnesium-Alloy Products |
ASTM E 527 : 2016 | Standard Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS) |
FED-STD-123 Revision H:2007 | MARKING FOR SHIPMENT (CIVIL AGENCIES) |
ASTM B 660 : 2015 | Standard Practices for Packaging/Packing of Aluminum and Magnesium Products |
ASTM E 1251 : 2004 | Test Method for Analysis of Aluminum and Aluminum Alloys by Atomic Emission Spectrometry |
ASTM E 1004 : 2017 | Standard Test Method for Determining Electrical Conductivity Using the Electromagnetic (Eddy Current) Method |
ASTM E 716 : 2016 : REDLINE | Standard Practices for Sampling and Sample Preparation of Aluminum and Aluminum Alloys for Determination of Chemical Composition by Spark Atomic Emission Spectrometry |
ASTM E 527 : 2016 : REDLINE | Standard Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS) |
ASTM B 557 : 1994 | Standard Test Methods of Tension Testing Wrought and Cast Aluminum- and Magnesium-Alloy Products |
ASTM E 1251 : 2011 | Standard Test Method for Analysis of Aluminum and Aluminum Alloys by Spark Atomic Emission Spectrometry |
ASTM E 290 : 2022 | Standard Test Methods for Bend Testing of Material for Ductility |
ASTM E 716 : 2016 : R2021 : EDT 1 | Standard Practices for Sampling and Sample Preparation of Aluminum and Aluminum Alloys for Determination of Chemical Composition by Spark Atomic Emission Spectrometry |
ASTM E 55 : 2023 | Standard Practice for Sampling Wrought Nonferrous Metals and Alloys for Determination of Chemical Composition |
ASTM E 290 : 2014 : REDLINE | Standard Test Methods for Bend Testing of Material for Ductility |
ASTM B 193 : 2016 : REDLINE | Standard Test Method for Resistivity of Electrical Conductor Materials |
ASTM B 253 : 2011 : R2017 | Standard Guide for Preparation of Aluminum Alloys for Electroplating |
ASTM E 55 : 2011 : R2017 | Standard Practice for Sampling Wrought Nonferrous Metals and Alloys for Determination of Chemical Composition |
ASTM E 1251 : 2017 : REV A | Standard Test Method for Analysis of Aluminum and Aluminum Alloys by Spark Atomic Emission Spectrometry |
ASTM E 1004 : 2017 : REDLINE | Standard Test Method for Determining Electrical Conductivity Using the Electromagnetic (Eddy Current) Method |
ASTM B 660 : 2015 : REDLINE | Standard Practices for Packaging/Packing of Aluminum and Magnesium Products |
ANSI H35.2M : 2013 | DIMENSIONAL TOLERANCES FOR ALUMINUM MILL PRODUCTS (METRIC) |
ASTM E 290 : 2014 | Standard Test Methods for Bend Testing of Material for Ductility |
ASTM E 55 : 2011 : R2022 : EDT 1 | Standard Practice for Sampling Wrought Nonferrous Metals and Alloys for Determination of Chemical Composition |
ASTM E 29 : 2022 | Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.