ASTM B 36/B36M : 2018
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Brass Plate, Sheet, Strip, And Rolled Bar
Hardcopy , PDF
19-10-2023
English
13-11-2018
This specification establishes the requirements brass plates, sheets, strips, and rolled bars made from UNS C21000, C22000, C22600, C23000, C24000, C26000, C26800, C27200, or C28000.
Committee |
B 05
|
DocumentType |
Standard
|
Pages |
9
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
1.1This specification establishes the requirements for brass plate, sheet, strip, and rolled bar of the following alloys:2
Copper Alloy | Previous | Nominal Composition | |
Copper, % | Zinc, % | ||
C21000 | Gilding, 95 % | 95 | 5 |
C22000 | Commerical Bronze, 90 % | 90 | 10 |
C22600 | Jewerly Bronze, 871/2% | 87.5 | 12.5 |
C23000 | Red Brass, 85 % | 85 | 15 |
C24000 | Low Brass, 80 % | 80 | 20 |
C26000 | Cartridge Brass, 70 % | 70 | 30 |
C26800 | Yellow Brass, 66 % | 66 | 34 |
C27200 | … | 63 | 37 |
C28000 | Muntz Metal, 60 % | 60 | 40 |
1.2Units—The values stated in either inch-pound units or SI units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.3This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM D 3658 : 2001 : R2016 | Standard Test Method for Determining the Torque Strength of Ultraviolet (UV) Light-Cured Glass/Metal Adhesive Joints |
ASTM B 927/B927M : 2017 | Standard Specification for Brass Rod, Bar, and Shapes |
ASTM D 1002 : 2010 : R2019 | Standard Test Method for Apparent Shear Strength of Single-Lap-Joint Adhesively Bonded Metal Specimens by Tension Loading (Metal-to-Metal) |
ASTM D 3165 : 2007 : R2023 | Standard Test Method for Strength Properties of Adhesives in Shear by Tension Loading of Single-Lap-Joint Laminated Assemblies |
ASTM F 1974 : 2023 | Standard Specification for Metal Insert Fittings for Polyethylene/Aluminum/Polyethylene and Crosslinked Polyethylene/Aluminum/Crosslinked Polyethylene Composite Pressure Pipe |
ASTM F 1018 : 2022 | Standard Specification for Steel Emergency Gear Stowage Locker |
ASTM D 5363 : 2016 | Standard Specification for Anaerobic Single-Component Adhesives (AN) |
ASTM F 1142 : 2019 | Standard Specification for Manhole Cover Assembly, Bolted, Semi-Flush, Oiltight and Watertight |
ASTM D 1384 : 2005 : R2019 | Standard Test Method for Corrosion Test for Engine Coolants in Glassware |
ASTM F 992 : 2017 : R2022 | Standard Specification for Valve Label Plates |
ASTM F 1143 : 2019 | Standard Specification for Manhole Cover Assembly, Bolted, Raised, Oiltight and Watertight |
ASTM B 315 : 2019 | Standard Specification for Seamless Copper Alloy Pipe and Tube |
ASTM E 18 : 2022 | Standard Test Methods for Rockwell Hardness of Metallic Materials |
ASTM D 3433 : 1999 : R2020 | Standard Test Method for Fracture Strength in Cleavage of Adhesives in Bonded Metal Joints |
ASTM F 1144 : 2019 | Standard Specification for Manhole Cover Assembly, Bolted, Semi-Flush, Oiltight and Watertight, Hinged |
ASTM D 3528 : 1996 : R2016 | Standard Test Method for Strength Properties of Double Lap Shear Adhesive Joints by Tension Loading |
ASTM D 4054 : 2023 | Standard Practice for Evaluation of New Aviation Turbine Fuels and Fuel Additives |
ASTM B 248M : 2022 | Standard Specification for General Requirements for Wrought Copper and Copper-Alloy Plate, Sheet, Strip, and Rolled Bar (Metric) |
ASTM E 8/E8M : 2016 : REV A : EDT 1 | Standard Test Methods for Tension Testing of Metallic Materials |
ASTM E 8/E8M : 2021 | Standard Test Methods for Tension Testing of Metallic Materials |
ASTM E 8/E8M : 2022 | Standard Test Methods for Tension Testing of Metallic Materials |
ASTM B 248 : 2017 | Standard Specification for General Requirements for Wrought Copper and Copper-Alloy Plate, Sheet, Strip, and Rolled Bar |
ASTM B 248M : 2017 | Standard Specification for General Requirements for Wrought Copper and Copper-Alloy Plate, Sheet, Strip, and Rolled Bar (Metric) |
ASTM E 478 : 2008 : R2017 | Standard Test Methods for Chemical Analysis of Copper Alloys |
ASTM E 112 : 2013 : R2021 | Standard Test Methods for Determining Average Grain Size |
ASTM E 112 : 2013 | Standard Test Methods for Determining Average Grain Size |
ASTM B 248 : 2022 | Standard Specification for General Requirements for Wrought Copper and Copper-Alloy Plate, Sheet, Strip, and Rolled Bar |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.