ASTM B 483/B483M : 2013 : EDT 1
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Aluminum and Aluminum-Alloy Drawn Tube and Drawn Pipe for General Purpose Applications
Hardcopy , PDF
16-06-2020
English
01-05-2013
CONTAINED IN VOL. 02.02, 2016 Defines aluminum and aluminum-alloy drawn tube and drawn pipe in straight lengths and tube in coils for general purpose applications in the alloys and tempers.
Committee |
B 07
|
DevelopmentNote |
Supersedes ASTM B 483. (05/2001)
|
DocumentType |
Standard
|
Pages |
9
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy |
1.1This specification covers aluminum and aluminum-alloy drawn tube and drawnpipe in straight lengths and tube in coils for general purpose applications in the alloys (Note 2), and tempers shown in Tables 1 and 2. Coiled tubes are generally available only as round tubes with a wall thickness not exceeding 0.083 in. [2.00 mm] and only in non-heat-treatable alloys.
1.2Alloy and temper designations are in accordance with ANSI H35.1/H35.1(M). The equivalent Unified Number System alloy designations are those of Table 3 preceded by A9, for example A91060 for aluminum 1060 in accordance with Practice E527.
1.3For acceptance criteria for inclusion of new aluminum and aluminum alloys in this specification, see Annex A2.
1.4The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.
1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
ANSI H35.2 : 2017 | DIMENSIONAL TOLERANCES FOR ALUMINUM MILL PRODUCTS |
ASTM B 234M : 2017 : REDLINE | Standard Specification for Aluminum and Aluminum-Alloy Drawn Seamless Tubes for Surface Condensers, Evaporators, and Heat Exchangers (Metric) |
ASTM E 1251 : 2007 | Standard Test Method for Analysis of Aluminum and Aluminum Alloys by Atomic Emission Spectrometry |
MIL-STD-129 Revision R:2014 | Military Marking for Shipment and Storage |
ASTM B 234 : 2017 : REDLINE | Standard Specification for Aluminum and Aluminum-Alloy Drawn Seamless Tubes for Surface Condensers, Evaporators, and Heat Exchangers |
ASTM B 918 : 2001 | Standard Practice for Heat Treatment of Wrought Aluminum Alloys |
ASTM E 607 : 2002 | Standard Test Method for Atomic Emission Spectrometric Analysis Aluminum Alloys by the Point to Plane Technique Nitrogen Atmosphere |
ANSI H35.1M : 2004 | ALLOY AND TEMPER DESIGNATION SYSTEMS FOR ALUMINUM (METRIC) |
ASTM B 666/B666M : 2015 : REDLINE | Standard Practice for Identification Marking of Aluminum and Magnesium Products |
ASTM E 1251 : 1994 : R1999 | Standard Test Method for Optical Emission Spectrometric Analysis of Aluminum and Aluminum Alloys by the Argon Atmosphere, Point-to-Plane, Unipolar Self-Initiating Capacitor Discharge |
SAE AMS 2770 : 2015 | HEAT TREATMENT OF WROUGHT ALUMINUM ALLOY PARTS |
ASTM E 1251 : 2017 | Standard Test Method for Analysis of Aluminum and Aluminum Alloys by Spark Atomic Emission Spectrometry |
ASTM B 557 : 2015 : REDLINE | Standard Test Methods for Tension Testing Wrought and Cast Aluminum- and Magnesium-Alloy Products |
FED-STD-123 Revision H:2007 | MARKING FOR SHIPMENT (CIVIL AGENCIES) |
SAE AMS 2772 : 2016 | HEAT TREATMENT OF ALUMINUM ALLOY RAW MATERIALS |
ASTM E 1251 : 2004 | Test Method for Analysis of Aluminum and Aluminum Alloys by Atomic Emission Spectrometry |
ASTM E 716 : 2016 : REDLINE | Standard Practices for Sampling and Sample Preparation of Aluminum and Aluminum Alloys for Determination of Chemical Composition by Spark Atomic Emission Spectrometry |
ASTM E 527 : 2016 : REDLINE | Standard Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS) |
ASTM B 557M : 2015 : REDLINE | Standard Test Methods for Tension Testing Wrought and Cast Aluminum- and Magnesium-Alloy Products (Metric) |
ASTM E 1251 : 2011 | Standard Test Method for Analysis of Aluminum and Aluminum Alloys by Spark Atomic Emission Spectrometry |
ANSI H35.1 : 2006 | ALLOY AND TEMPER DESIGNATION SYSTEMS FOR ALUMINUM |
ASTM B 241/B241M : 2016 : REDLINE | Standard Specification for Aluminum and Aluminum-Alloy Seamless Pipe and Seamless Extruded Tube |
ASTM E 1251 : 2017 : REV A | Standard Test Method for Analysis of Aluminum and Aluminum Alloys by Spark Atomic Emission Spectrometry |
ASTM B 660 : 2015 : REDLINE | Standard Practices for Packaging/Packing of Aluminum and Magnesium Products |
ANSI H35.2M : 2013 | DIMENSIONAL TOLERANCES FOR ALUMINUM MILL PRODUCTS (METRIC) |
ASTM E 215 : 2016 : REDLINE | Standard Practice for Standardizing Equipment and Electromagnetic Examination of Seamless Aluminum-Alloy Tube |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.