ASTM B 557 : 2015 : REDLINE
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Standard Test Methods for Tension Testing Wrought and Cast Aluminum- and Magnesium-Alloy Products
Available format(s)
PDF
Superseded date
29-10-2015
Language(s)
English
Published date
29-10-2015
Important note : Users cannot be edited or removed once added to your Multi user PDF.CONTAINED IN VOL. 02.02, 2015 Describes the tension testing of wrought and cast aluminum- and magnesium-alloy products, excepting aluminum foil, and are derived from Test Methods E 8, which cover the tension testing of all metallic materials.
| Committee |
B 07
|
| DocumentType |
Redline
|
| Pages |
16
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
1.1These test methods cover the tension testing of wrought and cast aluminum- and magnesium-alloy products, with the exception of aluminum foil,2 and are derived from Test Methods E8, which cover the tension testing of all metallic materials.
1.2The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.
1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Note 1:Foil is sheet metal less than 0.0079 in. thick. There is an overlap in the thickness range 0.006 to 0.0079 in. defined for foil and sheet. Sheet products in this thickness range are supplied to sheet product specifications and foil products in this thickness range are supplied to foil product specifications. Exceptions to the provisions of these test methods may need to be made in individual specifications or test methods for a particular material.
Note 2:A complete metric companion to Test Methods B557 has been developed—Test Methods B557M; therefore, no metric equivalents are presented in these test methods.
| ASTM B 91 : 2017 : REDLINE | Standard Specification for Magnesium-Alloy Forgings |
| ASTM B 199 : 2017 : REDLINE | Standard Specification for Magnesium-Alloy Permanent Mold Castings |
| MIL-DTL-45225 Revision F:1998 | ALUMINUM ALLOY ARMOR, FORGED |
| SAE AMS4226B | Aluminum Alloy Castings, High Strength 5.0Cu - 0.35Mn - 0.18Zr - 0.10V (224.0) Solution and Precipitation Heat Treated (Overaged) |
| ASTM B 317/B317M : 2007 | Standard Specification for Aluminum-Alloy Extruded Bar, Rod, Tube, Pipe, Structural Profiles, and Profiles for Electrical Purposes (Bus Conductor) |
| GR 1398 CORE : ISSUE 1 REV 1 | GENERIC REQUIREMENTS FOR COAXIAL DROP CABLE |
| ASTM B 531 : 1990 : R1998 : EDT 1 | Standard Specification for Aluminum-Alloy 5005 Drawing Stock for Electrical Purposes (Withdrawn 2003) |
| ASTM B 871 : 2001 : R2013 | Standard Test Method for Tear Testing of Aluminum Alloy Products (Withdrawn 2017) |
| ASTM B 211 : 2012 | Standard Specification for Aluminum and Aluminum-Alloy Rolled or Cold Finished Bar, Rod, and Wire |
| SAE AMSA21180C | Aluminum-Alloy Castings, High Strength |
| MIL-DTL-46192 Revision C:1998 | ALUMINUM ALLOY ARMOR ROLLED PLATE (1/2 TO 4 INCHES THICK), WELDABLE (ALLOY 2519) |
| SAE AMS4222H | Aluminum Alloy Castings, Sand, Moderate Heat Resistance 4.0Cu - 2.0Ni - 1.5Mg - 0.12Ti (242.0P) Solution Heat Treated and Stabilized |
| MIL-DTL-46063 Revision H:1998 | ARMOR PLATE, ALUMINUM ALLOY, 7039 |
| QQ-A-200 Revision E:1980 | ALUMINUM ALLOY, BAR, ROD, SHAPES, STRUCTURAL SHAPES, TUBE AND WIRE, EXTRUDED, GENERAL SPECIFICATION FOR |
| SAE AMS4302C | Aluminum Alloy, Laminated Sheet, Aramid Fiber Reinforced 5.7Zn - 2.2Mg - 1.6Cu - 0.22Cr (7475-T761) 3, 5, 7, or 9 Ply |
| MIL-DTL-32333 Base Document:2009 | ARMOR PLATE, MAGNESIUM ALLOY, AZ31B, APPLIQUE |
| MIL-A-22771 Revision D:1984 | ALUMINUM ALLOY FORGINGS, HEAT TREATED |
| QQ-A-225 Revision G:1990 | ALUMINUM AND ALUMINUM ALLOY BAR, ROD, WIRE, OR SPECIAL SHAPES, ROLLED, DRAWN, OR COLD FINISHED, GENERAL SPECIFICATION FOR |
| SAE AMSB20148C | Brazing Sheet, Aluminum Alloy |
| MIL A 46192 : B | ALUMINUM ALLOY ARMOR ROLLED PLATE (1/2 TO 4 INCHES THICK), WELDABLE (ALLOY 2519) |
| SAE AMS4362G | Forgings, Magnesium Alloy 5.5Zn - 0.45Zr (ZK60A-T5) Precipitation Heat Treated |
| MIL-DTL-32505 Revision A:2017 | ARMOR PLATE, ALUMINUM, ALLOYS 7017 AND 7020, WELDABLE |
| MIL-DTL-46083 Revision D:1998 | ALUMINUM ALLOY ARMOR, EXTRUDED, WELDABLE |
| MIL A 45225 : E | ALUMINUM ALLOY ARMOR, FORGED |
| ASTM B 736 : 2000 : R2006 | Standard Specification for Aluminum, Aluminum Alloy and Aluminum-Clad Steel Cable Shielding Stock (Withdrawn 2015) |
| ASTM B 947 : 2014 : REDLINE | Standard Practice for Hot Rolling Mill Solution Heat Treatment for Aluminum Alloy Plate |
| SAE AMSWWT700B | Tube, Aluminum and Aluminum Alloy, Drawn, Seamless, General Specification for |
| ASTM B 928/B928M : 2015 : REDLINE | Standard Specification for High Magnesium Aluminum-Alloy Products for Marine Service and Similar Environments |
| SCTE 15 : 2016 | SPECIFICATION FOR TRUNK, FEEDER AND DISTRIBUTION COAXIAL CABLE |
| AWS B4.0M : 2000 | STANDARD METHODS FOR MECHANICAL TESTING OF WELDS |
| AWS B4.0:2016 | STANDARD METHODS FOR MECHANICAL TESTING OF WELDS |
| SAE AMSQQA367E | Aluminum Alloy Forgings |
| SAE AMS4223E | Aluminum Alloy, Castings 4.5Cu - 0.70Ag - 0.30Mn - 0.25Mg - 0.25Ti (A201.0-T4) Solution Heat Treated and Naturally Aged |
| SAE AMS4281G | Aluminum Alloy Castings, Permanent Mold 5.0Si - 1.2Cu - 0.50Mg (355.0-T6) Solution and Precipitation Heat Treated |
| ASTM B 398/B398M : 2015 : REDLINE | Standard Specification for Aluminum-Alloy 6201-T81 and 6201-T83 Wire for Electrical Purposes |
| ASTM B 233 : 1997 : R2012 | Standard Specification for Aluminum 1350 Drawing Stock for Electrical Purposes |
| ASTM B 317/B317M : 2007 : R2015 : EDT 1 | Standard Specification for Aluminum-Alloy Extruded Bar, Rod, Tube, Pipe, Structural Profiles, and Profiles for Electrical Purposes (Bus Conductor) |
| ASTM B 871 : 2001 : R2007 | Standard Test Method for Tear Testing of Aluminum Alloy Products |
| ASTM B 945 :2006 | Standard Practice for Aluminum Alloy Extrusions Press Cooled from an Elevated Temperature Shaping Process for Production of T1, T2, T5 and T10-Type Tempers |
| ASTM B 491/B491M : 2015 : REDLINE | Standard Specification for Aluminum and Aluminum-Alloy Extruded Round Tubes for General-Purpose Applications |
| ASTM B 609/B609M : 2012 : R2016 | Standard Specification for Aluminum 1350 Round Wire, Annealed and Intermediate Tempers, for Electrical Purposes |
| ASTM B 945 : 2006 : R2014 | Standard Practice for Aluminum Alloy Extrusions Press Cooled from an Elevated Temperature Shaping Process for Production of T1, T2, T5 and T10–Type Tempers |
| ASTM B 230/B230M : 2007 : R2012 | Standard Specification for Aluminum 1350–H19 Wire for Electrical Purposes |
| ASTM B 324 : 2001 : R2016 | Standard Specification for Aluminum Rectangular and Square Wire for Electrical Purposes |
| SAE AMS QQ A 200 : 2004 | ALUMINUM ALLOY, BAR, ROD, SHAPES, STRUCTURAL SHAPES, TUBE, AND WIRE, EXTRUDED: GENERAL SPECIFICATION FOR |
| ASTM B 661 : 2012 : REDLINE | Standard Practice for Heat Treatment of Magnesium Alloys |
| ASTM B 317/B317M : 2007 : R2015 | Standard Specification for Aluminum-Alloy Extruded Bar, Rod, Tube, Pipe, Structural Profiles, and Profiles for Electrical Purposes (Bus Conductor) |
| ASTM B 316/B316M : 2015 : REDLINE | Standard Specification for Aluminum and Aluminum-Alloy Rivet and Cold-Heading Wire and Rods |
| MIL-A-21180 Revision D:1984 | ALUMINUM-ALLOY CASTINGS, HIGH STRENGTH |
| DOT/FAA/AR-MMPDS-01 : 20030131 | METALLIC MATERIALS PROPERTIES DEVELOPMENT AND STANDARDIZATION (MMPDS) |
| ASTM G 129 : 2000 : R2006 | Standard Practice for Slow Strain Rate Testing to Evaluate the Susceptibility of Metallic Materials to Environmentally Assisted Cracking |
| ASTM B 791 : 1997 | Specification for Zinc-Aluminum (ZA) Alloy Foundry Die Castings (Withdrawn 1999) |
| SAE AMS4249A | Aluminum Alloy Castings 7.0Si - 0.58Mg - 0.15Ti - 0.06Be (D357.0-T6) Solution and Precipitation Heat Treated (Requiring Fatigue and Fracture Toughness Testing) |
| ASTM B 236 : 2007 : R2015 | Standard Specification for Aluminum Bars for Electrical Purposes (Bus Bars) |
| ASTM B 800 : 2005 : R2015 | Standard Specification for 8000 Series Aluminum Alloy Wire for Electrical Purposes—Annealed and Intermediate Tempers |
| ASTM B 917/B917M : 2012 : REDLINE | Standard Practice for Heat Treatment of Aluminum-Alloy Castings from All Processes |
| SAE AMS4335A | Forgings, Aluminum Alloys 2xxx and 7xxx, Heat-Treated, Finished-Part Properties: Short-Transverse Tensile Properties and Fracture Toughness |
| MIL-A-12545 Revision D:1989 | ALUMINUM ALLOY IMPACTS |
| QQ-A-596 Revision E:1981 | ALUMINUM ALLOY PERMANENT AND SEMI-PERMANENT MOLD CASTINGS |
| SAE AMS4235C | Aluminum Alloy Castings 4.6Cu - 0.35Mn - 0.25Mg - 0.22Ti (A206.0-T7) Solution and Precipitation Heat Treated |
| ASTM B 800 : 2005 : R2011 | Standard Specification for 8000 Series Aluminum Alloy Wire for Electrical Purposes<char: emdash>Annealed and Intermediate Tempers |
| ASTM B 800 : 2005 | Standard Specification for 8000 Series Aluminum Alloy Wire for Electrical Purposes-Annealed and Intermediate Tempers |
| SAE AMS4490K | Magnesium Alloy Castings, Die 9.0Al - 0.70Zn (AZ91D, Temper F) As Cast |
| SAE AMS4411 | Aluminum Alloy Plate (7081-T7651) 7.2Zn - 1.5Cu - 2.0Mg - 0.10Zr Solution Heat Treated, Stress Relieved and Overaged |
| SAE AMS4227E | Aluminum Alloy, Castings, Sand, 8.0cu 6.0mg 0.50mn 0.50ni, as Cast |
| SAE AMS4420P | Magnesium Alloy Castings, Sand 6Al - 3Zn (AZ63A-F) As Cast |
| SAE AMS4482 | Cast Aluminum Alloy Composite 4.6 Cu – 3.4Ti – 1.4B – 0.75Ag – 0.27Mg (A205.0/TiB2/3p-T7P) Sand Cast, Solution and Precipitation Heat Treated |
| PREN 6071 : 200P1 | AEROSPACE SERIES - ALUMINIUM AND ALUMINIUM ALLOY WROUGHT PRODUCTS - TECHNICAL SPECIFICATION - PLATE |
| SAE AMSH6088C | Heat Treatment of Aluminum Alloys |
| ASTM B 241/B241M : 2016 : REDLINE | Standard Specification for Aluminum and Aluminum-Alloy Seamless Pipe and Seamless Extruded Tube |
| AWS D1.2/D1.2M : 2014 | STRUCTURAL WELDING CODE - ALUMINUM |
| SAE AMS 4483 : 2013 | MAGNESIUM ALLOY CASTINGS, PERMANENT MOLD, 10AL (AM100A-T6), SOLUTION AND PRECIPITATION HEAT TREATED |
| ASTM B 107/B107M : 2013 : REDLINE | Standard Specification for Magnesium-Alloy Extruded Bars, Rods, Profiles, Tubes, and Wire |
| ASTM B 324 : 2001 : R2007 | Standard Specification for Aluminum Rectangular and Square Wire for Electrical Purposes |
| ASTM B 221 : 2014 : REDLINE | Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes |
| SAE AMS2355M | Quality Assurance, Sampling and Testing Aluminum Alloys and Magnesium Alloy Wrought Products (Except Forging Stock), and Rolled, Forged, or Flash Welded Rings |
| SAE AMS4437F | Magnesium Alloy Castings, Sand 8.7Al - 0.70Zn (AZ91C-T6) Solution Heat Treated and Aged |
| ASTM B 230/B230M : 2007 : R2016 | Standard Specification for Aluminum 1350–H19 Wire for Electrical Purposes |
| ASTM E 9 : 2009 | Standard Test Methods of Compression Testing of Metallic Materials at Room Temperature |
| ASTM B 236 : 2007 | Standard Specification for Aluminum Bars for Electrical Purposes (Bus Bars) |
| ASTM B 80 : 2015 : REDLINE | Standard Specification for Magnesium-Alloy Sand Castings |
| ASTM G 129 : 2000 : R2013 | Standard Practice for Slow Strain Rate Testing to Evaluate the Susceptibility of Metallic Materials to Environmentally Assisted Cracking |
| ASTM B 211 : 2012 : EDT 1 | Standard Specification for Aluminum and Aluminum-Alloy Rolled or Cold Finished Bar, Rod, and Wire |
| MIL-STD-3049 Base Document:2013 | MATERIALS DEPOSITION, DDM: DIRECT DEPOSITION OF METAL FOR REMANUFACTURE, RESTORATION AND RECOATING |
| ASTM B 807/B807M : 2013 : REDLINE | Standard Practice for Extrusion Press Solution Heat Treatment for Aluminum Alloys |
| SAE AMS4286F | Aluminum Alloy Castings, Permanent Mold 7.0Si - 0.32Mg (356.0-T51) As-Cast then Precipitation Heat Treated |
| SAE AMS4410 | Aluminum Alloy Plate (7081-T7451) 7.2Zn - 1.5Cu - 2.0Mg - 0.10Zr Solution Heat Treated, Stress Relieved and Overaged |
| ASTM B 403 : 2012 : REDLINE | Standard Specification for Magnesium-Alloy Investment Castings |
| ASTM B 483/B483M : 2013 | Standard Specification for Aluminum and Aluminum-Alloy Drawn Pipe for General Purpose Applications |
| ASTM C 1671 : 2015 : REDLINE | Standard Practice for Qualification and Acceptance of Boron Based Metallic Neutron Absorbers for Nuclear Criticality Control for Dry Cask Storage Systems and Transportation Packaging |
| SAE AMS4424L | Magnesium Alloy Castings, Sand 6.0Al - 3.0Zn (AZ63-T6) Solution and Precipitation Heat Treated |
| SAE AMS4418H | Magnesium Alloy, Sand Castings 2.5Ag - 2.1Di - 0.70Zr (QE22A-T6) Solution and Precipitation Heat Treated |
| MIL A 46118 : D | ALUMINUM ALLOY ARMOR, 2219, ROLLED PLATE AND DIE FORGED SHAPES |
| SAE AMS2772G | Heat Treatment of Aluminum Alloy Raw Materials |
| SAE AMS4214J | Castings, Aluminum Alloy Sand 5.0Si - 1.2Cu - 0.50Mg (355.0-T71) Solution Heat Treated and Overaged |
| SAE AMS4285F | Aluminum Alloy Castings, Centrifugal 7.0Si - 0.30Mg (356.0-T6) Solution and Precipitation Heat Treated |
| SAE AMS4406A | Aluminum Alloy, Centrifugal Castings 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr (709.0-T61) Hot Isostatically Pressed, Solution and Precipitation Heat Treated |
| ASTM B 736 : 2000 | Standard Specification for Aluminum, Aluminum Alloy and Aluminum-Clad Steel Cable Shielding Stock |
| MIL A 46027 : H | ARMOUR PLATE, ALUMINUM ALLOY, WELDABLE 5083 AND 5456 |
| QQ-A-591 Revision F:1981 | ALUMINUM ALLOY DIE CASTINGS |
| SAE AMS 4440 : 1999 | MAGNESIUM ALLOY CASTINGS, SAND 3.5CE - 0.70ZR (EK41A-T5) PRECIPITATION HEAT TREATED |
| SAE AMS4439G | Magnesium Alloy Castings 4.2Zn - 1.2 Rare Earths - 0.7Zr (ZE41A-T5) Precipitation Heat Treated |
| MIL-M-6857 Revision D:1990 | MAGNESIUM ALLOY CASTINGS, HEAT TREATMENT OF |
| SAE AMS4293 | Aluminum Alloy Extrusions 7.9Zn - 1.6Cu - 2.2Mg - 0.16Cr (7249-T76511) Solution Heat Treated, Stress-Relieved, Straightened, and Overaged |
| MIL-DTL-12235 Revision A:2009 | PROJECTILE, PLATE-PROOFING (FOR IMPACT OR SHOCK TESTING) 37 MM M1000, 57 MM M1001, 75 MM M1002, 90 MM M1003, 105 MM M1004, 20 MM M1005, 57 MM M1001A, AND 75 MM M1002A |
| SAE AMS4212L | Aluminum Alloy Castings 5.0Si - 1.2Cu - 0.50Mg (355.0-T6) Solution and Precipitation Heat Treated |
| SAE AMS4225E | Aluminum Alloy, Heat-Resistant, Castings 5.0Cu - 1.5Ni - 0.25Mn - 0.25Sb - 0.25Co - 0.20Ti - 0.20Zr (203.0-T6) Solution Heat Treated and Precipitation Heat Treated |
| SAE AMS4229G | Aluminum Alloy Castings, High Strength 4.5Cu - 0.70Ag - 0.30Mn - 0.25Mg - 0.25Ti (A201.0-T7) Solution Heat Treated and Overaged |
| SAE AMS4417C | Castings, Sand, Magnesium Alloy 1.5Ag - 2.1Di - 0.08Cu - 0.70Zr (EQ21A - T6) Solution and Precipitation Heat Treated |
| SAE AMS3025E | Polyalkylene Glycol Heat Treat Quenchant |
| SAE AMS4231G | Castings, Sand, 4.5Cu - 1.1Si, Solution and Precipitation Heat Treated |
| SAE AMS4429A | Magnesium Alloy Castings, Sand 2.8Nd - 1.4Gd - 0.4Zn - 0.6Zr (EV31A - T6) Solution and Precipitation Heat Treated |
| ASTM B 483/B483M : 2013 : EDT 1 | Standard Specification for Aluminum and Aluminum-Alloy Drawn Tube and Drawn Pipe for General Purpose Applications |
| SAE AMS4284K | Aluminum Alloy Castings, Permanent Mold 7.0Si - 0.30Mg (356.0-T6) Solution and Precipitation Heat Treated |
| ASTM B 247 : 2015 : REDLINE | Standard Specification for Aluminum and Aluminum-Alloy Die Forgings, Hand Forgings, and Rolled Ring Forgings |
| ASTM B 918 : 2001 | Standard Practice for Heat Treatment of Wrought Aluminum Alloys |
| ASTM B 404/B404M : 2002 | Standard Specification for Aluminum and Aluminum-Alloy Seamless Condenser and Heat-Exchanger Tubes with Integral Fins (Withdrawn 2006) |
| SAE AMS4219F | Aluminum Alloy Castings 7.0Si - 0.55Mg - 0.12Ti - 0.06Be (A357.0 T6) Solution and Precipitation Heat Treated |
| SAE AMS4250B | Aluminum Alloy, Plate 8.1Zn - 2.3Mg - 1.0Cu - Zr (7449-T7651) Solution Heat Treated, Stress Relieved, and Overaged |
| ASTM B 230/B230M : 2007 | Standard Specification for Aluminum 1350-H19 Wire for Electrical Purposes |
| NASA PRC 2002 : 2011 | PROCESS SPECIFICATION FOR THE HEAT TREATMENT OF ALUMINUM ALLOYS |
| ASTM B 314 : 1990 | Specification for Aluminum 1350 Wire for Communication Cable (Withdrawn 1994) |
| MIL-DTL-46027 Revision K:2007 | ARMOR PLATE, ALUMINUM ALLOY, WELDABLE 5083, 5456, & 5059 |
| ASTM G 129 : 2000 | Standard Practice for Slow Strain Rate Testing to Evaluate the Susceptibility of Metallic Materials to Environmentally Assisted Cracking |
| SAE AMS4240G | Castings, Sand, 10Mg, Solution Heat Treated and Naturally Aged |
| MIL-R-12221 Revision D:1985 | RIVET, SOLID, ALUMINUM ALLOY, GRADE 7277, TEMPERED |
| ASTM B 90/B90M : 2015 : REDLINE | Standard Specification for Magnesium-Alloy Sheet and Plate |
| MIL-DTL-46118 Revision E:1998 | ALUMINUM ALLOY ARMOR, 2219, ROLLED PLATE AND DIE FORGED SHAPES |
| ASTM B 233 : 1997 : R2003 : EDT 1 | Standard Specification for Aluminum 1350 Drawing Stock for Electrical Purposes |
| ASTM B 871 : 2001 | Standard Test Method for Tear Testing of Aluminum Alloy Products |
| MIL A 46063 : G | ARMOUR PLATE, ALUMINUM ALLOY, 7039 |
| SAE AMS4299A | Aluminum Alloy, Plate (7449-T7951) 8.1Zn - 1.8Cu - 2.3Mg Solution Heat Treated, Stress Relieved, and Overaged |
| MIL A 46083 : B | ALUMINUM ALLOY ARMOR, EXTRUDED, WELDABLE |
| MIL-A-63547 Base Document:1982 | ALUMINUM ALLOY 7475, ROD |
| MIL-H-6088 Revision G:1991 | HEAT TREATMENT OF ALUMINIUM ALLOYS |
| ASTM B 646 : 2017 : REDLINE | Standard Practice for Fracture Toughness Testing of Aluminum Alloys |
| SAE AMS 4484 : 2013 | MAGNESIUM ALLOY CASTINGS, PERMANENT MOLD, 9.0AL - 2.0ZN (AZ92A-T6), SOLUTION AND PRECIPITATION HEAT TREATED |
| ASTM B 233 : 1997 : R2007 | Standard Specification for Aluminum 1350 Drawing Stock for Electrical Purposes |
| SAE AMS4261G | Aluminum Alloy Castings, Investment 7.0Si - 0.32Mg (356.0-T51) Precipitation Heat Treated |
| SAE AMSQQA591B | Aluminum Alloy Die Castings |
| SAE AMS QQ A 250 B : 2012 | ALUMINUM AND ALUMINUM ALLOY, PLATE AND SHEET GENERAL SPECIFICATION FOR |
| SAE AMS4236D | Aluminum Alloy Castings 4.6Cu - 0.35Mn - 0.25Mg - 0.22Ti (A206.0-T4) Solution Heat Treated and Naturally Aged |
| SAE AMS4452E | Magnesium Alloy, Investment Castings 8.7Al - 0.70Zn - 0.22Mn (AZ91C-T6) Solution and Precipitation Heat Treated |
| SAE AMS4215H | Aluminum Alloy, Castings 5.0Si - 1.2Cu - 0.50Mg (C355.0-T6) Solution and Precipitation Heat Treated |
| ASTM B 941 : 2016 : REDLINE | Standard Specification for Heat Resistant Aluminum-Zirconium Alloy Wire for Electrical Purposes |
| SAE AMS4442G | Magnesium Alloy Sand Castings 3.2 Rare Earths - 2.5Zn - 0.70Zr (EZ33A-T5) Precipitation Heat Treated |
| SAE AMSQQA225C | Aluminum and Aluminum Alloy, Bar, Rod, Wire, or Special Shapes; Rolled, Drawn, or Cold Finished; General Specification For |
| SAE AMS4485A | Magnesium Alloy, Extrusions 4.0Y - 2.25Nd - 0.5Zr (WE43C - T5) Precipitation Heat Treated |
| ASTM B 609/B609M : 2012 | Standard Specification for Aluminum 1350 Round Wire, Annealed and Intermediate Tempers, for Electrical Purposes |
| SAE AMS4453F | Magnesium Alloy, Investment Castings 9.0Al - 2.0Zn (AZ92A-T6) Solution and Precipitation Heat Treated |
| SAE AMS4371B | Magnesium Alloy, Plate 4.0Y - 2.25Nd - 0.5Zr (WE43C - T5) Precipitation Heat Treated |
| SAE J452_201801 | General Information - Chemical Compositions, Mechanical and Physical Properties of SAE Aluminum Casting Alloys |
| SAE AMS4241E | Aluminum Alloy Castings 7.0Si - 0.58Mg - 0.15Ti - 0.06Be (D357.0-T6) Solution and Precipitation Heat Treated Dendrite Arm Spacing (DAS) Controlled |
| SAE AMS4434N | Magnesium Alloy Castings, Sand 9.0Al - 2.0Zn (AZ92A-T6) Solution and Precipitation Heat Treated |
| ASTM E 1592 : 2005 : R2017 | Standard Test Method for Structural Performance of Sheet Metal Roof and Siding Systems by Uniform Static Air Pressure Difference |
| SAE J465_201801 | Magnesium Casting Alloys |
| ASTM B 609/B609M : 2012 : EDT 1 | Standard Specification for Aluminum 1350 Round Wire, Annealed and Intermediate Tempers, for Electrical Purposes |
| ASTM F 3122 : 2014 | Standard Guide for Evaluating Mechanical Properties of Metal Materials Made via Additive Manufacturing Processes |
| SAE AMS4455G | Magnesium Alloy, Investment Castings 10Al (AM100A-T6) Solution and Precipitation Heat Treated |
| ASTM B 324 : 2001 : R2012 | Standard Specification for Aluminum Rectangular and Square Wire for Electrical Purposes |
| ASTM E 1592 : 2005 | Standard Test Method for Structural Performance of Sheet Metal Roof and Siding Systems by Uniform Static Air Pressure Difference |
| SAE AMS4280J | Aluminum Alloy Castings, Permanent Mold 5.0Si - 1.2Cu - 0.5Mg (355.0-T71) Solution Heat Treated and Overaged |
| MIL-DTL-32375 Revision B:2017 | Armor Plate, Aluminum Alloy, 7085, 7056, 7075, 7181, and 7099, Unweldable Applique |
| MIL-DTL-32262 Revision A:2015 | ARMOR PLATE, ALUMINUM ALLOY 6055 WELDABLE & ALLOY 6061, UNWELDABLE APPLIQUE |
| ASTM E 8 : 2004 | Standard Test Methods for Tension Testing of Metallic Materials |
| SAE AMS4258B | Laminated Sheet, Aluminum Alloy, Aramid Fiber Reinforced 5.7Zn - 2.2Mg - 1.6Cu - 0.22Cr (Alclad, One Side 7475-T761) 5 or 7 Ply |
| SAE AMS 2768 : 2010 | HEAT TREATMENT OF MAGNESIUM ALLOY CASTINGS |
| SAE AMS 4426 : 2013 | CASTINGS, SAND, MAGNESIUM ALLOY 5.1Y - 3.0RE - 0.70ZR (WE54-T6) SOLUTION AND PRECIPITATION HEAT TREATED |
| SAE AMS4427C | Magnesium Alloy Castings, Sand 4.0Y - 2.3Nd - 0.7Zr (WE43B - T6) Solution and Precipitation Heat Treated |
| ASTM B 324:2001 | Standard Specification for Aluminum Rectangular and Square Wire for Electrical Purposes |
| SAE AMS4288 | Aluminum Alloy Castings 7.0Si - 0.58Mg - 0.15Ti (E357.0-T6) Solution and Precipitation Heat Treated |
| MIL-DTL-32341 Revision A:2015 | ARMOR PLATE, ALUMINUM, ALLOY 2139 WELDABLE & ALLOY 2195 AND 2060 UNWELDABLE APPLIQUE |
| QQ-A-601 Revision F:1981 | ALUMINUM ALLOY SAND CASTINGS |
| ASTM B 928 : 2004 | Standard Specification for High Magnesium Aluminum-Alloy Sheet and Plate for Marine Service |
| MIL-B-20148 Revision D:1987 | BRAZING SHEET, ALUMINUM ALLOY |
| SAE AMS4444E | Magnesium Alloy Castings, Sand 6.0Zn - 0.80Zr (ZK61A-T5) Precipitation Heat Treated |
| ASTM B 234 : 2017 : REDLINE | Standard Specification for Aluminum and Aluminum-Alloy Drawn Seamless Tubes for Surface Condensers, Evaporators, and Heat Exchangers |
| SAE AMS4471A | Cast Aluminum Alloy Composite 4.6Cu - 3.4Ti - 1.4B - 0.75Ag - 0.27Mg (205.0/TiB2/3p-T7P) Investment Cast, Solution and Precipitation Heat Treated |
| ASTM E 8/E8M : 2016-09 | TEST METHODS FOR TENSION TESTING OF METALLIC MATERIALS |
| SAE AMS 4305 : 2012 | ALUMINUM ALLOY, EXTRUDED PROFILES (7449-T79511) 8.1ZN - 1.8CU - 2.2MG - 0.16ZR SOLUTION HEAT TREATED, STRESS RELIEVED, AND OVERAGED (COMPOSITION SIMILAR TO UNS A97449) |
| SAE AMS4217J | Aluminum Alloy, Castings 7.0Si - 0.32Mg (356.0-T6) Solution and Precipitation Heat Treated |
| SAE AMS4425D | Magnesium Alloy Castings, Sand 5.8Zn - 2.5RE - 0.70Zr (ZE63-T6) Solution and Precipitation Heat Treated |
| SAE AMS4107G | Aluminum Alloy Die Forgings (7050-T74) Solution Heat Treated and Overaged |
| ASTM B 807 : 2002 | Standard Practice for Extrusion Press Solution Heat Treatment for Aluminum Alloys |
| ASTM E 1592 : 2005 : R2012 | Standard Test Method for Structural Performance of Sheet Metal Roof and Siding Systems by Uniform Static Air Pressure Difference |
| SAE AMS4242C | Aluminum Alloy, Castings 4.7Cu - 0.60Ag - 0.35Mn - 0.25Mg - 0.25Ti (B201.0-T7) Solution Heat Treated and Overaged |
| SAE AMS4201F | Aluminum Alloy Plate 6.2Zn - 2.3Cu - 2.2Mg - 0.12Zr (7050-T7651) Solution Heat Treated, Stress Relieved, and Overaged |
| SAE AMS4443H | Magnesium Alloy, Sand Castings 4.5Zn - 0.75Zr (ZK51A-T5) Precipitation Heat Treated |
| ASTM B 209 : 2014 : REDLINE | Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate |
| ASTM E 602 : 2003 | Standard Test Method for Sharp-Notch Tension Testing with Cylindrical Specimens (Withdrawn 2010) |
| ASTM B 233 : 1997 : R2016 | Standard Specification for Aluminum 1350 Drawing Stock for Electrical Purposes |
| ASTM B 233 : 1997 | Standard Specification for Aluminum 1350 Drawing Stock for Electrical Purposes |
| ASTM E 345 : 2016 : REDLINE | Standard Test Methods of Tension Testing of Metallic Foil |
| ASTM E 83 : 2016 : REDLINE | Standard Practice for Verification and Classification of Extensometer Systems |
| ASTM B 209 : 2014 : REDLINE | Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate |
| ASTM E 8 : 2004 | Standard Test Methods for Tension Testing of Metallic Materials |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.