Customer Support: +353 (0)1 857 6730

Corporate Website About Us
  • Shopping Cart
    There are no items in your cart
Please enter a keyword to search
Advanced search
Home
ASTM
ASTM B 618/B618M : 2018

ASTM B 618/B618M : 2018

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by

Standard Specification for Aluminum-Alloy Investment Castings

Available format(s)

Hardcopy , PDF

Superseded date

31-08-2020

Superseded by

ASTM B 618/B618M : 2018 : EDT 1

Language(s)

English

Published date

15-05-2018

Publisher

American Society for Testing and Materials

€74.48
Excluding VAT
EUR
CAD
CHF
CNY
DKK
EUR
GBP
HKD
IDR
INR
JPY
KRW
MXN
NOK
NZD
SEK
SGD
USD
ZAR
Hardcopy - English
PDF - English
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20

Committee
B 07
DocumentType
Standard
Pages
14
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

1.1This specification covers aluminum-alloy investment castings designated as shown in Table 1.

(A)When single units are shown, they indicate the maximum amounts permitted.
(B)Analysis shall be made for the elements for which limits are shown in this table.
(C)The following applies to all specified limits in this table: For purposes of determining conformance to these limits, an observed value or a calculated value obtained from analysis shall be rounded to the nearest unit in the last right-hand place of figures used in expressing the specified limit in accordance with the rounding-off method of Practice E29.
(D)In case of discrepancy between the values listed in Table 1 and those listed in the “Designations and Composition Limits for Aluminum Alloys in the Form of Castings and Ingot (known as the ‘Pink Sheets’),” the composition limits registered with the Aluminum Association and published in the “Pink Sheets” shall be considered the controlling composition.
(E)“Others” includes listed elements for which no specific limit is shown as well as unlisted metallic elements. The producer may analyze samples for trace elements not specified in the specification. However, such analysis is not required and may not cover all metallic “Others” elements. Should any analysis by the producer or the purchaser establish that an “Others” element exceeds the limit of “Each” or that the aggregate of several “Others” elements exceeds the limit of “Total,” the material shall be considered nonconforming.
(F)Other Elements—Total shall be the sum of unspecified metallic elements 0.010 % or more, rounded to the second decimal before determining the sum.
(G)If iron exceeds 0.45 %, manganese content shall not be less than one half of the iron content.
(H)The Aluminum Association ruling on the number of decimal places to which Mg percent is expressed is exempted for some long standing alloys. See A2.2.6.
(I)710.0 formerly A712.0, 712.0 formerly D712.0, 851.0 formerly A850.0, 852.0 formerly B850.0.
(J)For a cross reference of current and former alloy designations see the Aluminum Association’s “Designations and Chemical Composition Limits for Aluminum Alloys in the Form of Castings and Ingot (The Pink Sheets).”

1.2This specification is for aluminum-alloy investment castings used in general purpose applications. It may not address the mechanical properties integrity testing and verification required for highly loaded or safety critical applications.

1.3Alloy and temper designations are in accordance with ANSI H35.1/H35.1 (M).

1.4Unless the order specifies the “M” specification designation, the material shall be furnished to the inch-pound units.

1.5For acceptance criteria for inclusion of new aluminum and aluminum alloys and their properties in this specification, see Annex A1 and Annex A2.

1.6Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.

1.7This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.8This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Get in touch with us