ASTM B 827 : 2005 : R2020
Current
The latest, up-to-date edition.
Standard Practice for Conducting Mixed Flowing Gas (MFG) Environmental Tests
Hardcopy , PDF
English
11-04-2023
Committee |
B 02
|
DocumentType |
Standard Practice
|
Pages |
9
|
PublisherName |
American Society for Testing and Materials
|
Status |
Current
|
Supersedes |
1.1This practice provides procedures for conducting environmental tests involving exposures to controlled quantities of corrosive gas mixtures.
1.2This practice provides for the required equipment and methods for gas, temperature, and humidity control which enable tests to be conducted in a reproducible manner. Reproducibility is measured through the use of control coupons whose corrosion films are evaluated by mass gain, coulometry, or by various electron and X-ray beam analysis techniques. Reproducibility can also be measured by in situ corrosion rate monitors using electrical resistance or mass/frequency change methods.
1.3The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use. See 5.1.2.4.
1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM B 942 : 2021 | Standard Guide for Specification and Quality Assurance for the Electrical Contact Performance of Crimped Wire Terminations |
ASTM B 825 : 2019 | Standard Test Method for Coulometric Reduction of Surface Films on Metallic Test Samples |
ASTM B 845 : 1997 : R2018 | Standard Guide for Mixed Flowing Gas (MFG) Tests for Electrical Contacts |
ASTM B 826 : 2009 : R2020 | Standard Test Method for Monitoring Atmospheric Corrosion Tests by Electrical Resistance Probes |
ASTM B 845 : 1997 : R2018 | Standard Guide for Mixed Flowing Gas (MFG) Tests for Electrical Contacts |
ASTM D 3609 : 2000 : R2014 | Standard Practice for Calibration Techniques Using Permeation Tubes |
ASTM B 810 : 2001 : REV A : R2022 | Standard Test Method for Calibration of Atmospheric Corrosion Test Chambers by Change in Mass of Copper Coupons |
ASTM B 825 : 2019 | Standard Test Method for Coulometric Reduction of Surface Films on Metallic Test Samples |
ASTM D 2914 : 2015 : R2022 | Standard Test Methods for Sulfur Dioxide Content of the Atmosphere (West-Gaeke Method) |
ASTM B 810 : 2001 : REV A : R2017 | Standard Test Method for Calibration of Atmospheric Corrosion Test Chambers by Change in Mass of Copper Coupons |
ASTM B 845 : 1997 : R2024 | Standard Guide for Mixed Flowing Gas (MFG) Tests for Electrical Contacts |
ASTM D 3824 : 2020 | Standard Test Methods for Continuous Measurement of Oxides of Nitrogen in the Ambient or Workplace Atmosphere by Chemiluminescence |
ASTM D 3609 : 2022 | Standard Practice for Calibration Techniques Using Permeation Tubes |
ASTM B 765 : 2003 : R2018 | Standard Guide for Selection of Porosity and Gross Defect Tests for Electrodeposits and Related Metallic Coatings |
ASTM D 2914 : 2015 | Standard Test Methods for Sulfur Dioxide Content of the Atmosphere (West-Gaeke Method) |
ASTM D 3464 : 1996 : R2023 | Standard Test Method for Average Velocity in a Duct Using a Thermal Anemometer |
ASTM D 3464 : 1996 : R2014 | Standard Test Method for Average Velocity in a Duct Using a Thermal Anemometer |
ASTM B 808 : 2010 : R2020 | Standard Test Method for Monitoring of Atmospheric Corrosion Chambers by Quartz Crystal Microbalances |
ASTM B 542 : 2013 : R2019 | Standard Terminology Relating to Electrical Contacts and Their Use |
ASTM B 826 : 2009 : R2020 | Standard Test Method for Monitoring Atmospheric Corrosion Tests by Electrical Resistance Probes |
ASTM B 765 : 2003 : R2023 | Standard Guide for Selection of Porosity and Gross Defect Tests for Electrodeposits and Related Metallic Coatings |
ASTM B 542 : 2024 | Standard Terminology Relating to Electrical Contacts and Their Use |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.