ASTM B 858 : 2006 : R2018
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Ammonia Vapor Test for Determining Susceptibility to Stress Corrosion Cracking in Copper Alloys
Hardcopy , PDF
31-07-2024
English
01-03-2018
CONTAINED IN VOL. 02.01, 2018 Defines a procedure to determine the presence of residual stresses in wrought copper alloy products that may lead to stress corrosion cracking.
Committee |
B 05
|
DocumentType |
Test Method
|
Pages |
4
|
ProductNote |
Reconfirmed 2018
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
1.1This test method describes a procedure to determine the presence of residual stresses in wrought copper alloy products that may lead to stress corrosion cracking. An ammonia vapor atmosphere is used as an accelerated test.
1.2This test method is only suitable for products fabricated from copper alloys that are known to be susceptible to stress corrosion cracking in ammonia vapor atmospheres. It is intended to create an environmental condition of reproducible severity.
Note 1:It is well known that the critical step in the cracking mechanism is the development of an environment in the condensate film that occurs on the surface of the test specimen, and is rich in copper complex ions.
1.3The severity of this test method depends upon the pH of the corrosive solution. In Annex A1 are given four different atmospheres to which the product may be exposed, and the appropriate pH of the solution to be used for the test, depending on the risk level associated with the intended application.
1.3.1The appropriate pH value for the test shall be specified in the product specification, or as per established agreement between the supplier and purchaser, with respect to the alloy and its intended application.
1.4Units—The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM B 552 : 2019 | Standard Specification for Seamless and Welded Copper–Nickel Tubes for Water Desalting Plants |
ASTM B 150/B150M : 2019 | Standard Specification for Aluminum Bronze Rod, Bar, and Shapes |
ASTM B 395/B395M : 2018 | Standard Specification for U-Bend Seamless Copper and Copper Alloy Heat Exchanger and Condenser Tubes |
ASTM B 950 : 2023 | Standard Guide for Editorial Procedures and Form of Product Specifications for Copper and Copper Alloys |
ASTM B 371/B371M : 2019 | Standard Specification for Copper-Zinc-Silicon Alloy Rod |
ASTM B 19 : 2020 | Standard Specification for Cartridge Brass Sheet, Strip, Plate, Bar, and Disks |
ASTM B 21/B21M : 2020 | Standard Specification for Naval Brass Rod, Bar, and Shapes |
ASTM B 956 : 2019 : EDT 1 | Standard Specification for Welded Copper and Copper-Alloy Condenser and Heat Exchanger Tubes with Integral Fins |
ASTM B 359/B359M : 2023 | Standard Specification for Copper and Copper-Alloy Seamless Condenser and Heat Exchanger Tubes With Integral Fins |
ASTM F 3226/F3226M : 2019 : REDLINE | Standard Specification for Metallic Press-Connect Fittings for Piping and Tubing Systems |
ASTM B 135/B135M : 2017 | Standard Specification for Seamless Brass Tube |
ASTM B 138/B138M : 2011 : R2024 | Standard Specification for Manganese Bronze Rod, Bar, and Shapes |
ASTM B 43 : 2020 | Standard Specification for Seamless Red Brass Pipe, Standard Sizes |
ASTM B 111/B111M : 2024 | Standard Specification for Copper and Copper-Alloy Seamless Condenser Tubes and Ferrule Stock |
ASTM B 1014 : 2020 | Standard Specification for Welded Copper and Copper Alloy Condenser and Heat Exchanger Tubes with a Textured Surface(s) |
ASTM B 249/B249M : 2023 | Standard Specification for General Requirements for Wrought Copper and Copper-Alloy Rod, Bar, Shapes and Forgings |
ASTM B 543/B543M : 2018 | Standard Specification for Welded Copper and Copper-Alloy Heat Exchanger Tube |
ASTM B 154 : 2016 : REDLINE | Standard Test Method for Mercurous Nitrate Test for Copper Alloys |
ASTM D 1193 : 1977 : R1983 : EDT 1 | Standard Specification for Reagent Water |
ASTM B 154 : 2016 | Standard Test Method for Mercurous Nitrate Test for Copper Alloys |
ASTM D 1193 : 2006 : R2011 | Standard Specification for Reagent Water |
ASTM D 1193 : 1991 | Standard Specification for Reagent Water |
ASTM B 846 : 2011-07 | TERMINOLOGY FOR COPPER AND COPPER ALLOYS |
ASTM D 1193 : 1970 | Standard Specification For Reagent Water |
ASTM D 1193 : 2006 | Standard Specification for Reagent Water |
ASTM D 1193 : 1999 | Standard Specification for Reagent Water |
ASTM D 1193 : 2006 : R2018 | Standard Specification for Reagent Water |
ASTM B 154 : 2016 : R2022 | Standard Test Method for Mercurous Nitrate Test for Copper Alloys |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.