ASTM B 860 : 2018
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Zinc Master Alloys for Use in Hot Dip Galvanizing
Hardcopy , PDF
12-11-2022
English
31-01-2019
Committee |
B 02
|
DocumentType |
Standard
|
Pages |
3
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
1.1This specification covers zinc master alloys which are used in hot dip galvanizing for the purpose of adjusting the concentration of certain alloying elements in the molten zinc bath. Table 1 covers the chemical composition of these materials which include six master alloys of zinc-aluminum (brightener) and one master alloy of zinc-antimony.
ASTM | Common | UNS | |
Type A-1 | 90/10 Zn/Al | High Purity | Z30750 |
Type A-2 | 90/10 Zn/Al | Low Purity | Z31710 |
Type A-3 | 95/5 Zn/Al | High Purity | Z30503 |
Type A-4 | 95/5 Zn/Al | Low Purity | Z31510 |
Type A-5 | 96/4 Zn/Al | High Purity | Z31520 |
Type A-6 | 96/4 Zn/Al | Low Purity | Z30504 |
Type S-1 | 90/10 Zn/Sb | Z55710 |
Note 1:The master alloys in Specification B860 are intended to be used primarily in hot-dip galvanizing to adjust the concentration of certain elements in a molten zinc bath, and differ from the zinc-aluminum alloys in Specification B997 which are intended to be used primarily in molten zinc-aluminum.
1.2The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use.
1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM B 914 : 2021 | Standard Practice for Color Codes on Zinc and Zinc Alloy Ingot for Use in Hot-Dip Galvanizing of Steel |
ASTM B 997 : 2016 : R2021 | Standard Specification for Zinc-Aluminum Alloys in Ingot Form for Hot-Dip Coatings |
ASTM B 949 : 2018 | Standard Specification for General Requirements for Zinc and Zinc Alloy Products |
ASTM E 29 : 2013 : R2019 | Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications |
ASTM B 997 : 2016 : EDT 1 | Standard Specification for Zinc-Aluminum Alloys in Ingot Form for Hot-Dip Coatings |
ASTM E 29 : 2002 | Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications |
ASTM B 997 : 2016 : R2021 | Standard Specification for Zinc-Aluminum Alloys in Ingot Form for Hot-Dip Coatings |
ASTM B 899 : 2021 | Standard Terminology Relating to Non-ferrous Metals and Alloys |
ASTM B 899 : 2018 | Standard Terminology Relating to Non-ferrous Metals and Alloys |
ASTM E 29 : 2022 | Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.