• Shopping Cart
    There are no items in your cart

ASTM B 928/B928M : 2015 : R2023 : EDT 1

Current

Current

The latest, up-to-date edition.

Standard Specification for High Magnesium Aluminum-Alloy Products for Marine Service and Similar Environments

Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

31-10-2023

€61.92
Excluding VAT

Committee
B 07
DocumentType
Standard
Pages
15
ProductNote
ε1 NOTE—Editorially updated Section 2 in October 2023.
PublisherName
American Society for Testing and Materials
Status
Current
Supersedes

1.1This specification covers high magnesium aluminum-alloy products in the mill finish condition that are intended for marine hull construction and other marine applications where frequent or constant direct contact with seawater is expected and for similar environments (Note 1). Aluminum alloy products covered by this specification include the alloy-tempers of flat sheet, coiled sheet, and plate shown in Table 2 [Table 3] and Table 4 [Table 5], and alloy-tempers of extruded profiles shown in Table 6 [Table 7].

Note 1:There are other aluminum alloy-temper products that may be suitable for use in marine and similar environments, but which may not require the corrosion resistance testing specified by B928/B928M. See Specification B209/B209M for other aluminum sheet and plate alloy-temper products. For other aluminum extruded alloy-temper products see Specification B221 or B221M and/or other relevant specifications for aluminum extruded products.

1.2Alloy and temper designations are in accordance with ANSI H35.1/H35.1 (M). The equivalent Unified Numbering System alloy designations are those of Table 1 preceded by A9, for example, A95083 for 5083 in accordance with Practice E527.

1.3The values stated in either SI units (Table 3 and Table 5) or inch-pound units (Table 2 and Table 4) are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of each other. Combining values from the two systems may result in non-conformance with the standard.

1.4For acceptance criteria for inclusion of new aluminum and aluminum alloys in this specification, see Annex A2.

1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ASTM C 1802 : 2023 Standard Specification for Design, Testing, Manufacture, Selection, and Installation of Horizontal Fabricated Metal Access Hatches for Utility, Water, and Wastewater Structures
ASTM B 881 : 2017 Standard Terminology Relating to Aluminum- and Magnesium-Alloy Products
ASTM B 209/B209M : 2021 : REV A Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate

ASTM B 985 : 2024 Standard Practice for Sampling Aluminum Ingots, Billets, Castings and Finished or Semi-Finished Wrought Aluminum Products for Compositional Analysis
ASTM B 660 : 2021 Standard Practices for Packaging/Packing of Aluminum and Magnesium Products
ASTM G 67 : 2024 : REV A Standard Test Method for Determining the Susceptibility to Intergranular Corrosion of 5XXX Series Aluminum Alloys by Mass Loss After Exposure to Nitric Acid (NAMLT Test)
ASTM G 67 : 2018 Standard Test Method for Determining the Susceptibility to Intergranular Corrosion of 5XXX Series Aluminum Alloys by Mass Loss After Exposure to Nitric Acid (NAMLT Test)
ASTM E 50 : 2017 Standard Practices for Apparatus, Reagents, and Safety Considerations for Chemical Analysis of Metals, Ores, and Related Materials
ASTM B 660 : 2023 Standard Practices for Packaging/Packing of Aluminum and Magnesium Products
ASTM E 50 : 2024 Standard Practices for Apparatus, Reagents, and Safety Considerations for Chemical Analysis of Metals, Ores, and Related Materials
ASTM G 66 : 1999 : R2018 : EDT 1 Standard Test Method for Visual Assessment of Exfoliation Corrosion Susceptibility of 5XXX Series Aluminum Alloys (ASSET Test)
ASTM B 985 : 2012 : R2016 Standard Practice for Sampling Aluminum Ingots, Billets, Castings and Finished or Semi-Finished Wrought Aluminum Products for Compositional Analysis
ASTM G 67 : 2024 Standard Test Method for Determining the Susceptibility to Intergranular Corrosion of 5XXX Series Aluminum Alloys by Mass Loss After Exposure to Nitric Acid (NAMLT Test)
ASTM G 66 : 2023 Standard Test Method for Visual Assessment of Exfoliation Corrosion Susceptibility of 5XXX Series Aluminum Alloys (ASSET Test)

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.