ASTM B 939 : 2021
Current
The latest, up-to-date edition.
Standard Test Method for Radial Crushing Strength, K, of Powder Metallurgy (PM) Bearings and Structural Materials
Hardcopy , PDF
English
13-04-2021
Committee |
B 09
|
DocumentType |
Test Method
|
Pages |
4
|
PublisherName |
American Society for Testing and Materials
|
Status |
Current
|
Supersedes |
1.1This test method covers the equipment and laboratory procedure for the determination of the radial crushing strength of materials using either a plain powder metallurgy (PM) bearing or a thin-walled hollow cylindrical test specimen. This is a destructive test that produces quantitative results.
1.2Limitations:
1.2.1The principle of this procedure is based on the material being tested having minimal ductility. The permanent deflection of the cylinder during the test should not exceed 10 % of the outside diameter.
1.2.2The radial crushing strength test results should be used only as a guide if the test specimen has a wall thickness that is greater than one-third of the outside diameter. These test results should then only be used for comparison with data from the test specimens of like materials and similar dimensions.
1.3Units—With the exception of the values for density and the mass used to determine density, for which the use of the gram per cubic centimetre (g/cm3) and gram (g) units are the industry standard, the values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM B 439 : 2018 | Standard Specification for Iron-Base Powder Metallurgy (PM) Bearings (Oil-Impregnated) |
ASTM B 925 : 2015 | Standard Practices for Production and Preparation of Powder Metallurgy (PM) Test Specimens |
ASTM B 438 : 2017 | Standard Specification for Bronze-Base Powder Metallurgy (PM) Bearings (Oil-Impregnated) |
ASTM E 456 : 2013 : REV A : R2022 | Standard Terminology Relating to Quality and Statistics |
ASTM E 456 : 2013 : REV A : R2022 : EDT 1 | Standard Terminology Relating to Quality and Statistics |
ASTM B 439 : 2018 | Standard Specification for Iron-Base Powder Metallurgy (PM) Bearings (Oil-Impregnated) |
ASTM E 691 : 2020 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
ASTM E 456 : 2013 : REV A : R2017 : EDT 5 | Standard Terminology Relating to Quality and Statistics |
ASTM B 925 : 2015 | Standard Practices for Production and Preparation of Powder Metallurgy (PM) Test Specimens |
ASTM B 243 : 2022 | Standard Terminology of Powder Metallurgy |
ASTM E 691 : 2023 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
ASTM E 691 : 2022 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
ASTM B 243 : 2020 | Standard Terminology of Powder Metallurgy |
ASTM E 691 : 2021 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
ASTM B 438 : 2021 | Standard Specification for Bronze-Base Powder Metallurgy (PM) Bearings (Oil-Impregnated) |
ASTM B 243 : 2023 | Standard Terminology of Powder Metallurgy |
ASTM B 438 : 2017 | Standard Specification for Bronze-Base Powder Metallurgy (PM) Bearings (Oil-Impregnated) |
ASTM B 925 : 2015 : R2022 | Standard Practices for Production and Preparation of Powder Metallurgy (PM) Test Specimens |
ASTM E 456 : 2013 : REV A : R2017 : EDT 4 | Standard Terminology Relating to Quality and Statistics |
ASTM E 456 : 2013 : REV A : R2017 : EDT 6 | Standard Terminology Relating to Quality and Statistics |
ASTM B 243 : 2024 | Standard Terminology of Powder Metallurgy |
ASTM B 439 : 2021 | Standard Specification for Iron-Base Powder Metallurgy (PM) Bearings (Oil-Impregnated) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.