ASTM B 967/B967M : 2018 : R2023
Current
The latest, up-to-date edition.
Standard Specification for Copper-Zinc-Tin-Bismuth Alloy Rod, Bar and Wire
Hardcopy , PDF
English
01-05-2023
Important note : Users cannot be edited or removed once added to your Multi user PDF.| Committee |
B 05
|
| DocumentType |
Standard
|
| Pages |
5
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Current
|
| Supersedes |
1.1This specification establishes the requirements for copper-zinc-tin-bismuth alloy rod, bar and wire of alloy UNS Nos. C49250, C49255, C49260, C49265, C49300, C49340, C49345, C49350, C49355, and C49360 intended for use in plumbing applications and drinking water systems.
1.2Typically, rod and bar product made to this specification is furnished as straight lengths. Wire (H04) 0.08 in. to 0.3 in. [2 mm to 8 mm inclusive] is furnished in coil form, and H50 shapes.
1.3Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.4The following safety hazard caveat pertains only to the test method(s) described in this specification.
1.4.1This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM F 3226/F3226M : 2019 : REDLINE | Standard Specification for Metallic Press-Connect Fittings for Piping and Tubing Systems |
| ASTM F 1960 : 2023 : REV A | Standard Specification for Cold Expansion Fittings with PEX Reinforcing Rings for Use with Cross-linked Polyethylene (PEX) and Polyethylene of Raised Temperature (PE-RT) Tubing |
| ASTM B 249/B249M : 2022 | Standard Specification for General Requirements for Wrought Copper and Copper-Alloy Rod, Bar, Shapes and Forgings |
| ASTM B 250/B250M : 2019 | Standard Specification for General Requirements for Wrought Copper Alloy Wire |
| ASTM F 1807 : 2023 | Standard Specification for Metal Insert Fittings Utilizing a Copper Crimp Ring, or Alternate Stainless Steel Clamps, for SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Polyethylene of Raised Temperature (PE-RT) Tubing |
| ASTM F 2929 : 2017 : R2021 | Standard Specification for Crosslinked Polyethylene (PEX) Tubing of 0.070 in. Wall and Fittings for Radiant Heating Systems up to 75 psig |
| ASTM E 8/E8M : 2024 | Standard Test Methods for Tension Testing of Metallic Materials |
| ASTM E 92 : 2023 | Standard Test Methods for Vickers Hardness and Knoop Hardness of Metallic Materials |
| ASTM B 846 : 2019 : REV A | Standard Terminology for Copper and Copper Alloys |
| ASTM E 478 : 2024 | Standard Test Methods for Chemical Analysis of Copper Alloys |
| ASTM B 846 : 2024 | Standard Terminology for Copper and Copper Alloys |
| ASTM E 527 : 2023 | Standard Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS) |
| ASTM E 92 : 2017 | Standard Test Methods for Vickers Hardness and Knoop Hardness of Metallic Materials |
| ASTM E 527 : 2016 | Standard Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS) |
| ASTM E 8/E8M : 2022 | Standard Test Methods for Tension Testing of Metallic Materials |
| ASTM B 249/B249M : 2023 | Standard Specification for General Requirements for Wrought Copper and Copper-Alloy Rod, Bar, Shapes and Forgings |
| ASTM B 249/B249M : 2022 | Standard Specification for General Requirements for Wrought Copper and Copper-Alloy Rod, Bar, Shapes and Forgings |
| ASTM E 478 : 2008 : R2017 | Standard Test Methods for Chemical Analysis of Copper Alloys |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.