ASTM B 985 : 2024
Current
The latest, up-to-date edition.
Standard Practice for Sampling Aluminum Ingots, Billets, Castings and Finished or Semi-Finished Wrought Aluminum Products for Compositional Analysis
Hardcopy , PDF
English
01-07-2024
Committee |
B 07
|
DocumentType |
Standard Practice
|
Pages |
8
|
PublisherName |
American Society for Testing and Materials
|
Status |
Current
|
Supersedes |
1.1This practice describes procedures for sampling unwrought aluminum ingots, billets, castings and finished or semi-finished wrought aluminum products to obtain a representative sample for determining chemical composition.
1.1.1Chemical compositions determined from samples obtained in accordance with this standard practice may differ from the bulk chemical composition determined from samples taken when ingots or castings are poured. These differences can be due to elemental segregation that occurs during solidification, procedures that remove enriched material (for example, ingot scalping), or procedures that remove depleted areas (for example, removal of the riser from a casting).
1.1.2Analysis of samples obtained from unwrought aluminum ingots, billets, and castings and finished or semi-finished wrought aluminum products can be used to determine if the piece sampled meets The Aluminum Association, Inc. registered chemical composition limits or other specified chemical composition limits for the alloy. Analysis of such samples shall not supersede the analysis of samples taken during pouring of castings or ingots in accordance with Practices E716 and analyzed in accordance with Test Methods E1251, E3061, or EN 14242 and shall not be used for determining compliance with chemical composition requirements for an entire cast lot or part thereof.
Note 1:Pieces may include ingots, forgings, coils, sheets, extrusions, castings, and so forth. A single unwrought ingot or billet may produce multiple finished or semi-finished pieces.
Note 2:Certification of entire cast lots should be determined using samples taken during pouring of castings or ingots in accordance with Practices E716 and analyzed in accordance with Test Methods E1251, E3061, or EN 14242.
1.2Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM B 632/B632M : 2024 | Standard Specification for Aluminum-Alloy Rolled Tread Plate |
ASTM E 716 : 2016 : R2021 : EDT 2 | Standard Practices for Sampling and Sample Preparation of Aluminum and Aluminum Alloys for Determination of Chemical Composition by Spark Atomic Emission Spectrometry |
ASTM B 236/B236M : 2023 | Standard Specification for Aluminum Bars for Electrical Purposes (Bus Bars) |
ASTM B 210/B210M : 2019 : REV A | Standard Specification for Aluminum and Aluminum-Alloy Drawn Seamless Tubes |
ASTM B 241/B241M : 2022 | Standard Specification for Aluminum and Aluminum-Alloy Seamless Pipe and Seamless Extruded Tube |
ASTM E 3061 : 2024 | Standard Test Method for Analysis of Aluminum and Aluminum Alloys by Inductively Coupled Plasma Atomic Emission Spectrometry (Performance Based) |
ASTM B 969/B969M : 2018 : EDT 1 | Standard Specification for Aluminum-Alloy Castings Produced by Squeeze Casting, and the Semi-Solid Thixocast and Rheocast Casting Processes |
ASTM B 308/B308M : 2020 | Standard Specification for Aluminum-Alloy 6061-T6 Standard Structural Profiles |
ASTM B 955/B955M : 2018 | Standard Specification for Aluminum-Alloy Centrifugal Castings |
ASTM B 108/B108M : 2019 | Standard Specification for Aluminum-Alloy Permanent Mold Castings |
ASTM B 247 : 2020 | Standard Specification for Aluminum and Aluminum-Alloy Die Forgings, Hand Forgings, and Rolled Ring Forgings |
ASTM B 618/B618M : 2018 : EDT 1 | Standard Specification for Aluminum-Alloy Investment Castings |
ASTM B 179 : 2018 | Standard Specification for Aluminum Alloys in Ingot and Molten Forms for Castings from All Casting Processes |
ASTM B 211/B211M : 2023 | Standard Specification for Aluminum and Aluminum-Alloy Rolled or Cold Finished Bar, Rod, and Wire |
ASTM B 234M : 2017 | Standard Specification for Aluminum and Aluminum-Alloy Drawn Seamless Tubes for Surface Condensers, Evaporators, and Heat Exchangers (Metric) |
ASTM B 483/B483M : 2021 | Standard Specification for Aluminum and Aluminum-Alloy Drawn Tube and Drawn Pipe for General Purpose Applications |
ASTM B 373 : 2019 | Standard Specification for Aluminum Foil for Capacitors |
ASTM B 429/B429M : 2020 | Standard Specification for Aluminum-Alloy Extruded Structural Pipe and Tube |
ASTM B 247M : 2020 | Standard Specification for Aluminum and Aluminum-Alloy Die Forgings, Hand Forgings, and Rolled Ring Forgings (Metric) |
ASTM B 221M : 2021 | Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes (Metric) |
ASTM B 928/B928M : 2015 : R2023 : EDT 1 | Standard Specification for High Magnesium Aluminum-Alloy Products for Marine Service and Similar Environments |
ASTM B 26/B26M : 2018 : EDT 1 | Standard Specification for Aluminum-Alloy Sand Castings |
ASTM B 316/B316M : 2020 | Standard Specification for Aluminum and Aluminum-Alloy Rivet and Cold-Heading Wire and Rods |
ASTM B 686/B686M : 2018 | Standard Specification for Aluminum Alloy Castings, High-Strength |
ASTM B 221 : 2021 | Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes |
ASTM B 491/B491M : 2023 | Standard Specification for Aluminum and Aluminum-Alloy Extruded Round Tubes for General-Purpose Applications |
ASTM B 234 : 2017 | Standard Specification for Aluminum and Aluminum-Alloy Drawn Seamless Tubes for Surface Condensers, Evaporators, and Heat Exchangers |
ASTM E 1251 : 2017 : REV A | Standard Test Method for Analysis of Aluminum and Aluminum Alloys by Spark Atomic Emission Spectrometry |
ASTM B 317/B317M : 2023 | Standard Specification for Aluminum-Alloy Extruded Bar, Rod, Tube, Pipe, Structural Profiles, and Profiles for Electrical Purposes (Bus Conductor) |
ASTM B 209/B209M : 2021 : REV A | Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate |
ASTM E 135 : 2024 | Standard Terminology Relating to Analytical Chemistry for Metals, Ores, and Related Materials |
ASTM E 135 : 2023 : REV A | Standard Terminology Relating to Analytical Chemistry for Metals, Ores, and Related Materials |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.