ASTM C 1068 : 2003 : R2011
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Guide for Qualification of Measurement Methods by a Laboratory Within the Nuclear Industry
Hardcopy , PDF
11-11-2014
English
01-06-2011
Important note : Users cannot be edited or removed once added to your Multi user PDF.| Committee |
C 26
|
| DocumentType |
Guide
|
| Pages |
4
|
| ProductNote |
Reconfirmed 2011
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1 This guide provides guidance for selecting, validating, and qualifying measurement methods when qualification is required for a specific program. The recommended practices presented in this guide provide a major part of a quality assurance program for the laboratory data (see Fig. 1). Qualification helps to assure that the data produced will meet established requirements.
1.2 The activities intended to assure the quality of analytical laboratory measurement data are diagrammed in Fig. 1. Discussion and guidance related to some of these activities appear in the following sections:
| Section | |
| Selection of Measurement Methods | 5 |
| Validation of Measurement Methods | 6 |
| Qualification of Measurement Methods | 7 |
| Control | 8 |
| Personnel Qualification | 9 |
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
FIG. 1 Quality Assurance of Analytical Laboratory Data
| ASTM C 1742 : 2017 | Standard Test Method for Isotopic Analysis of Uranium Hexafluoride by Double Standard Single-Collector Gas Mass Spectrometer Method (Withdrawn 2023) |
| ASTM C 1672 : 2017 | Standard Test Method for Determination of Uranium or Plutonium Isotopic Composition or Concentration by the Total Evaporation Method Using a Thermal Ionization Mass Spectrometer |
| ASTM C 697 : 2016 | Standard Test Methods for Chemical, Mass Spectrometric, and Spectrochemical Analysis of Nuclear-Grade Plutonium Dioxide Powders and Pellets |
| ASTM C 1865 : 2018 | Standard Test Method for The Determination of Carbon and Sulfur Content in Plutonium Oxide Powder by the Direct Combustion-Infrared Spectrophotometer |
| ASTM C 1210 : 2018 | Standard Guide for Establishing a Measurement System Quality Control Program for Analytical Chemistry Laboratories Within the Nuclear Industry |
| ASTM C 1128 : 2018 | Standard Guide for Preparation of Working Reference Materials for Use in Analysis of Nuclear Fuel Cycle Materials |
| ASTM C 759 : 2018 | Standard Test Methods for Chemical, Mass Spectrometric, Spectrochemical, Nuclear, and Radiochemical Analysis of Nuclear-Grade Plutonium Nitrate Solutions |
| ASTM C 1267 : 2017 | Standard Test Method for Uranium by Iron (II) Reduction in Phosphoric Acid Followed by Chromium (VI) Titration in the Presence of Vanadium |
| ASTM C 1853 : 2017 | Standard Test Method for The Determination of Carbon (Total) Content in Mixed Oxide ((U, Pu)O<inf>2</inf>) Sintered Pellets by Direct Combustion-Infrared Detection Method |
| ASTM C 758 : 2018 | Standard Test Methods for Chemical, Mass Spectrometric, Spectrochemical, Nuclear, and Radiochemical Analysis of Nuclear-Grade Plutonium Metal |
| ASTM C 1156 : 2018 | Standard Guide for Establishing Calibration for a Measurement Method Used to Analyze Nuclear Fuel Cycle Materials |
| ASTM C 1817 : 2016 | Standard Test Method for The Determination of the Oxygen to Metal (O/M) Ratio in Sintered Mixed Oxide ((U, Pu)O<inf>2</inf>) Pellets by Gravimetry |
| ASTM C 1625 : 2012 | Standard Test Method for Uranium and Plutonium Concentrations and Isotopic Abundances by Thermal Ionization Mass Spectrometry |
| ASTM C 1854 : 2017 | Standard Test Method for Determination of Hydrogen (total from all sources) in Mixed Oxide ((U, Pu)O<inf>2</inf>) Sintered Pellets by the Inert Gas Fusion Technique Followed by Thermal Conductivity Measurement |
| ASTM C 1316 : 2008 : R2017 | Standard Test Method for Nondestructive Assay of Nuclear Material in Scrap and Waste by Passive-Active Neutron Counting Using <sup>252</sup>Cf Shuffler |
| ASTM C 1187 : 2015 | Standard Guide for Establishing Surveillance Test Program for Boron-Based Neutron Absorbing Material Systems for Use in Nuclear Fuel Storage Racks In a Pool Environment |
| ASTM C 1855 : 2018 | Standard Test Method for Determination of Uranium and Plutonium Concentration in Aqueous Solutions Using Hybrid K-Edge Densitometry and X-Ray Fluorescence |
| ASTM C 1009 : 2013 : REV A | Standard Guide for Establishing and Maintaining a Quality Assurance Program for Analytical Laboratories Within the Nuclear Industry |
| ASTM C 698 : 2016 | Standard Test Methods for Chemical, Mass Spectrometric, and Spectrochemical Analysis of Nuclear-Grade Mixed Oxides ((U, Pu)O<inf>2</inf>) |
| ASTM C 1832 : 2016 | Standard Test Method for Determination of Uranium Isotopic Composition by the Modified Total Evaporation (MTE) Method Using a Thermal Ionization Mass Spectrometer |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.