![header thumbnail](/images/publishers\astm_cover.gif)
ASTM C 1116/C1116M : 2010 : REV A : R2015
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
![header thumbnail](/images/publishers\astm_cover.gif)
Standard Specification for Fiber-Reinforced Concrete
Hardcopy , PDF
29-09-2023
English
12-05-2015
CONTAINED IN VOL. 04.02, 2015 Describes all forms of fiber-reinforced concrete that are delivered to a purchaser with the ingredients uniformly mixed, and that can be sampled and tested at the point of delivery.
Committee |
C 09
|
DevelopmentNote |
Supersedes ASTM C 1116 (01/2007)
|
DocumentType |
Standard
|
Pages |
7
|
ProductNote |
Reconfirmed 2015
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
1.1This specification covers all forms of fiber-reinforced concrete that are delivered to a purchaser with the ingredients uniformly mixed, and that can be sampled and tested at the point of delivery. It does not cover the placement, consolidation, curing, or protection of the fiber-reinforced concrete after delivery to the purchaser.
1.2Certain sections of this specification are also applicable to fiber-reinforced concrete intended for shotcreting by the dry-mix process when sampling and testing of concrete is possible only at the point of placement. In this case, the sections dealing with batching plant, mixing equipment, mixing and delivery, and measurement of workability and air content, are not applicable.
1.3This specification does not cover thin-section glass fiber-reinforced concrete manufactured by the spray-up process that is under the jurisdiction of ASTM Subcommittee C27.40.
1.4The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.5The following precautionary statement pertains only to the test method portion, Sections 15 and 18, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
ASTM C 118M : 2019 | Standard Specification for Concrete Pipe for Irrigation or Drainage (Metric) (Withdrawn 2024) |
ASTM C 412 : 2019 | Standard Specification for Concrete Drain Tile |
ASTM C 507M : 2022 | Standard Specification for Reinforced Concrete Elliptical Culvert, Storm Drain, and Sewer Pipe (Metric) |
ASTM C 1786 : 2019 | Standard Specification for Segmental Precast Reinforced Concrete Box Sections for Culverts, Storm Drains, and Sewers Designed According to AASHTO LRFD |
ASTM C 926 : 2023 | Standard Specification for Application of Portland Cement-Based Plaster |
ASTM C 1433 : 2020 : EDT 1 | Standard Specification for Precast Reinforced Concrete Monolithic Box Sections for Culverts, Storm Drains, and Sewers |
ASTM C 1846/C1846M : 2019 | Standard Specification for Performance Based Manufacture of Reinforced Concrete Culvert, Storm Drain, and Sewer Pipe |
ASTM C 118 : 2019 | Standard Specification for Concrete Pipe for Irrigation or Drainage |
ASTM C 506M : 2022 : REV A | Standard Specification for Reinforced Concrete Arch Culvert, Storm Drain, and Sewer Pipe (Metric) |
ASTM C 412M : 2019 | Standard Specification for Concrete Drain Tile (Metric) |
ASTM C 1818 : 2022 | Standard Specification for Synthetic Fiber Reinforced Concrete Culvert, Storm Drain, and Sewer Pipe |
ASTM D 7508/D7508M : 2020 | Standard Specification for Polyolefin Chopped Strands for Use in Concrete |
ASTM C 1731 : 2021 | Standard Specification for Concrete Floor Tile |
ASTM C 478/C478M : 2022 | Standard Specification for Circular Precast Reinforced Concrete Manhole Sections |
ASTM C 655M : 2019 : REV A | Standard Specification for Reinforced Concrete D-Load Culvert, Storm Drain, and Sewer Pipe (Metric) |
ASTM C 505M : 2019 | Standard Specification for Nonreinforced Concrete Irrigation Pipe With Rubber Gasket Joints (Metric) |
ASTM C 985 : 2022 | Standard Specification for Nonreinforced Concrete Specified Strength Culvert, Storm Drain, and Sewer Pipe |
ASTM C 76M : 2022 : REV A | Standard Specification for Reinforced Concrete Culvert, Storm Drain, and Sewer Pipe (Metric) |
ASTM C 654M : 2019 | Standard Specification for Porous Concrete Pipe (Metric) |
ASTM C 507 : 2022 | Standard Specification for Reinforced Concrete Elliptical Culvert, Storm Drain, and Sewer Pipe |
ASTM C 506 : 2022 : REV A | Standard Specification for Reinforced Concrete Arch Culvert, Storm Drain, and Sewer Pipe |
ASTM C 1504M : 2020 | Standard Specification for Manufacture of Precast Reinforced Concrete Three-Sided Structures for Culverts and Storm Drains (Metric) |
ASTM C 1417 : 2019 | Standard Specification for Manufacture of Reinforced Concrete Sewer, Storm Drain, and Culvert Pipe for Direct Design |
ASTM C 1227 : 2023 | Standard Specification for Precast Concrete Septic Tanks |
ASTM C 655 : 2019 : REV A | Standard Specification for Reinforced Concrete D-Load Culvert, Storm Drain, and Sewer Pipe |
ASTM C 1670/C1670M : 2023 | Standard Specification for Adhered Manufactured Stone Masonry Veneer Units |
ASTM C 1433M : 2022 | Standard Specification for Precast Reinforced Concrete Monolithic Box Sections for Culverts, Storm Drains, and Sewers (Metric) |
ASTM C 76 : 2022 : REV A | Standard Specification for Reinforced Concrete Culvert, Storm Drain, and Sewer Pipe |
ASTM C 1613 : 2022 | Standard Specification for Precast Concrete Gravity Grease Interceptor Tanks |
ASTM C 94/C94M : 2023 | Standard Specification for Ready-Mixed Concrete |
ASTM C 387/C387M : 2023 | Standard Specification for Packaged, Dry, Combined Materials for Concrete and High Strength Mortar |
ASTM C 654 : 2019 | Standard Specification for Porous Concrete Pipe |
ASTM C 1417M : 2019 | Standard Specification for Manufacture of Reinforced Concrete Sewer, Storm Drain, and Culvert Pipe for Direct Design (Metric) |
ASTM C 1577 : 2020 : EDT 1 | Standard Specification for Precast Reinforced Concrete Monolithic Box Sections for Culverts, Storm Drains, and Sewers Designed According to AASHTO LRFD |
ASTM C 505 : 2019 | Standard Specification for Nonreinforced Concrete Irrigation Pipe with Rubber Gasket Joints |
ASTM C 1504 : 2020 | Standard Specification for Manufacture of Precast Reinforced Concrete Three-Sided Structures for Culverts and Storm Drains |
ASTM C 14 : 2020 | Standard Specification for Nonreinforced Concrete Sewer, Storm Drain, and Culvert Pipe |
ASTM C 985M : 2022 | Standard Specification for Nonreinforced Concrete Specified Strength Culvert, Storm Drain, and Sewer Pipe (Metric) |
ASTM C 1903 : 2021 | Standard Specification for Precast Concrete Duct Bank |
ASTM C 14M : 2020 | Standard Specification for Nonreinforced Concrete Sewer, Storm Drain, and Culvert Pipe (Metric) |
ACI PRC 506.5:2022 | Specifying Underground Shotcrete - Guide |
ASTM C 1077 : 2007 | Standard Practice for Laboratories Testing Concrete and Concrete Aggregates for Use in Construction and Criteria for Laboratory Evaluation |
ASTM C 1077 : 2002 | Standard Practice for Laboratories Testing Concrete and Concrete Aggregates for Use in Construction and Criteria for Laboratory Evaluation |
ASTM C 1550 : 2005 | Standard Test Method for Flexural Toughness of Fiber Reinforced Concrete (Using Centrally Loaded Round Panel) |
ASTM C 125 : 2021 | Standard Terminology Relating to Concrete and Concrete Aggregates |
ASTM C 1077 : 2006 : REV A | Standard Practice for Laboratories Testing Concrete and Concrete Aggregates for Use in Construction and Criteria for Laboratory Evaluation |
ASTM C 138/C138M : 2014 | Standard Test Method for Density (Unit Weight), Yield, and Air Content (Gravimetric) of Concrete |
ASTM C 31/C31M : 2019 : REV A | Standard Practice for Making and Curing Concrete Test Specimens in the Field |
ASTM C 1077 : 2007 : REV A | Standard Practice for Laboratories Testing Concrete and Concrete Aggregates for Use in Construction and Criteria for Laboratory Evaluation |
ASTM C 173/C173M : 2014 | Standard Test Method for Air Content of Freshly Mixed Concrete by the Volumetric Method |
ASTM C 173/C173M : 2009 | Standard Test Method for Air Content of Freshly Mixed Concrete by the Volumetric Method |
ASTM C 1077 : 2010 : REV C | Standard Practice for Laboratories Testing Concrete and Concrete Aggregates for Use in Construction and Criteria for Laboratory Evaluation |
ASTM C 94/C94M : 2021 : REV B | Standard Specification for Ready-Mixed Concrete |
ASTM D 7357 : 2007 : R2012 | Standard Specification for Cellulose Fibers for Fiber-Reinforced Concrete |
ASTM C 31/C31M : 2022 | Standard Practice for Making and Curing Concrete Test Specimens in the Field |
ASTM C 138/C138M : 2023 | Standard Test Method for Density (Unit Weight), Yield, and Air Content (Gravimetric) of Concrete |
ASTM C 1077 : 2003 | Standard Practice for Laboratories Testing Concrete and Concrete Aggregates for Use in Construction and Criteria for Laboratory Evaluation |
ASTM C 31/C31M : 2021 : REV A | Standard Practice for Making and Curing Concrete Test Specimens in the Field |
ASTM C 1399 : 2001 | Test Method for Obtaining Average Residual-Strength of Fiber-Reinforced Concrete |
ASTM D 6942 : 2003 : R2012 | Standard Test Method for Stability of Cellulose Fibers in Alkaline Environments |
ASTM C 39/C39M : 2021 | Standard Test Method for Compressive Strength of Cylindrical Concrete Specimens |
ASTM C 1077 : 2011 : REV A | Standard Practice for Agencies Testing Concrete and Concrete Aggregates for Use in Construction and Criteria for Testing Agency Evaluation |
ASTM C 1077 : 2009 : REV A | Standard Practice for Laboratories Testing Concrete and Concrete Aggregates for Use in Construction and Criteria for Laboratory Evaluation |
ASTM C 192/C192M : 2000 | Standard Practice for Making and Curing Concrete Test Specimens in the Laboratory |
ASTM A 820/A820M : 2022 | Standard Specification for Steel Fibers for Fiber-Reinforced Concrete |
ASTM C 1550 : 2004 | Standard Test Method for Flexural Toughness of Fiber Reinforced Concrete (Using Centrally Loaded Round Panel) |
ASTM C 1550 : 2003 : REV A | Standard Test Method for Flexural Toughness of Fiber Reinforced Concrete (Using Centrally Loaded Round Panel) |
ASTM C 1077 : 2016 | Standard Practice for Agencies Testing Concrete and Concrete Aggregates for Use in Construction and Criteria for Testing Agency Evaluation |
ASTM C 1436 : 2008 | Standard Specification for Materials for Shotcrete |
ASTM C 1077 : 2011 : REV B | Standard Practice for Agencies Testing Concrete and Concrete Aggregates for Use in Construction and Criteria for Testing Agency Evaluation |
ACI 211.1 : 1991 | SELECTING PROPORTIONS FOR NORMAL, HEAVYWEIGHT AND MASS CONCRETE |
ASTM C 31/C31M : 2023 | Standard Practice for Making and Curing Concrete Test Specimens in the Field |
ASTM C 1077 : 2005 : REV B | Standard Practice for Laboratories Testing Concrete and Concrete Aggregates for Use in Construction and Criteria for Laboratory Evaluation |
ASTM C 125 : 2000 | Standard Terminology Relating to Concrete and Concrete Aggregates |
ASTM C 1077 : 2016 : REV A | Standard Practice for Agencies Testing Concrete and Concrete Aggregates for Use in Construction and Criteria for Testing Agency Evaluation |
ASTM C 1077 : 2008 | Standard Practice for Laboratories Testing Concrete and Concrete Aggregates for Use in Construction and Criteria for Laboratory Evaluation |
ASTM C 1077 : 2017 | Standard Practice for Agencies Testing Concrete and Concrete Aggregates for Use in Construction and Criteria for Testing Agency Evaluation |
ASTM C 94/C94M : 2021 : REV A | Standard Specification for Ready-Mixed Concrete |
ASTM C 1077 : 2005 : REV B : EDT 1 | Standard Practice for Laboratories Testing Concrete and Concrete Aggregates for Use in Construction and Criteria for Laboratory Evaluation |
ASTM C 1436 : 2013 : REDLINE | Standard Specification for Materials for Shotcrete |
ASTM D 6942 : 2003 : R2008 | Standard Test Method for Stability of Cellulose Fibers in Alkaline Environments |
ASTM C 42/C 42M : 2016-10 | TEST METHOD FOR OBTAINING AND TESTING DRILLED CORES AND SAWED BEAMS OF CONCRETE |
ASTM C 39/C39M : 2015 : REV A | Standard Test Method for Compressive Strength of Cylindrical Concrete Specimens |
ASTM C 1550 : 2019 | Standard Test Method for Flexural Toughness of Fiber Reinforced Concrete (Using Centrally Loaded Round Panel) |
ASTM C 1550 : 2003 | Standard Test Method for Flexural Toughness of Fiber Reinforced Concrete (Using Centrally Loaded Round Panel) |
ASTM C 1550 : 2010 | Standard Test Method for Flexural Toughness of Fiber Reinforced Concrete (Using Centrally Loaded Round Panel) |
ASTM C 1077 : 2017 : REDLINE | Standard Practice for Agencies Testing Concrete and Concrete Aggregates for Use in Construction and Criteria for Testing Agency Evaluation |
ASTM C 1077 : 2006 | Standard Practice for Laboratories Testing Concrete and Concrete Aggregates for Use in Construction and Criteria for Laboratory Evaluation |
ASTM C 1077 : 2015 | Standard Practice for Agencies Testing Concrete and Concrete Aggregates for Use in Construction and Criteria for Testing Agency Evaluation |
ASTM C 1077 : 2014 | Standard Practice for Agencies Testing Concrete and Concrete Aggregates for Use in Construction and Criteria for Testing Agency Evaluation |
ASTM C 1077 : 2010 : REV B | Standard Practice for Laboratories Testing Concrete and Concrete Aggregates for Use in Construction and Criteria for Laboratory Evaluation |
ASTM C 1666/C1666M : 2008 : R2015 | Standard Specification for Alkali Resistant (AR) Glass Fiber for GFRC and Fiber-Reinforced Concrete and Cement |
ASTM C 1077 : 2013 : REV A | Standard Practice for Agencies Testing Concrete and Concrete Aggregates for Use in Construction and Criteria for Testing Agency Evaluation |
ASTM C 1140 : 2003 : REV A | Standard Practice for Preparing and Testing Specimens from Shotcrete Test Panels |
ASTM C 1077 : 2005 | Standard Practice for Laboratories Testing Concrete and Concrete Aggregates for Use in Construction and Criteria for Laboratory Evaluation |
ASTM C 192/C192M : 2016-04 | PRACTICE FOR MAKING AND CURING CONCRETE TEST SPECIMENS IN THE LABORATORY |
ASTM C 39/C39M : 2020 | Standard Test Method for Compressive Strength of Cylindrical Concrete Specimens |
ASTM C 666/C666M : 2015 : REDLINE | Standard Test Method for Resistance of Concrete to Rapid Freezing and Thawing |
ASTM C 1077 : 2010 | Standard Practice for Laboratories Testing Concrete and Concrete Aggregates for Use in Construction and Criteria for Laboratory Evaluation |
ASTM C 1399 : 2002 | Test Method for Obtaining Average Residual-Strength of Fiber-Reinforced Concrete |
ASTM C 1666/C1666M : 2008 : R2023 | Standard Specification for Alkali Resistant (AR) Glass Fiber for GFRC and Fiber-Reinforced Concrete and Cement |
ASTM C 173/C173M : 2016 : REDLINE | Standard Test Method for Air Content of Freshly Mixed Concrete by the Volumetric Method |
ASTM C 94/C94M : 2022 : REV A | Standard Specification for Ready-Mixed Concrete |
ASTM C 1077 : 2010 : REV A | Standard Practice for Laboratories Testing Concrete and Concrete Aggregates for Use in Construction and Criteria for Laboratory Evaluation |
ASTM C 1399 : 2004 | Test Method for Obtaining Average Residual-Strength of Fiber-Reinforced Concrete |
ASTM C 1602/C1602M : 2018 | Standard Specification for Mixing Water Used in the Production of Hydraulic Cement Concrete |
ASTM C 1436 : 2013 | Standard Specification for Materials for Shotcrete (Withdrawn 2022) |
ASTM C 1077 : 2015 : REV A | Standard Practice for Agencies Testing Concrete and Concrete Aggregates for Use in Construction and Criteria for Testing Agency Evaluation |
ASTM C 31/C31M : 2021 | Standard Practice for Making and Curing Concrete Test Specimens in the Field |
ASTM C 1140 : 2003 | Standard Practice for Preparing and Testing Specimens from Shotcrete Test Panels |
ASTM C 143/C143M : 2015 : REV A | Standard Test Method for Slump of Hydraulic-Cement Concrete |
ASTM C 1550 : 2012 | Standard Test Method for Flexural Toughness of Fiber Reinforced Concrete (Using Centrally Loaded Round Panel) |
ASTM C 94/C94M : 2021 | Standard Specification for Ready-Mixed Concrete |
ACI 211.2 : 1998 | SELECTING PROPORTIONS FOR STRUCTURAL LIGHTWEIGHT CONCRETE |
ASTM C 1550 : 2008 | Standard Test Method for Flexural Toughness of Fiber Reinforced Concrete (Using Centrally Loaded Round Panel) |
ASTM C 1550 : 2002 | Standard Test Method for Flexural Toughness of Fiber Reinforced Concrete (Using Centrally Loaded Round Panel) |
ASTM C 1602/C1602M : 2022 | Standard Specification for Mixing Water Used in the Production of Hydraulic Cement Concrete |
ASTM C 1077 : 2009 : REV B | Standard Practice for Laboratories Testing Concrete and Concrete Aggregates for Use in Construction and Criteria for Laboratory Evaluation |
ASTM C 1077 : 2000 | Standard Practice for Laboratories Testing Concrete and Concrete Aggregates for Use in Construction and Criteria for Laboratory Evaluation |
ASTM C 125 : 2021 : REV A | Standard Terminology Relating to Concrete and Concrete Aggregates |
ASTM C 31/C31M : 2017 | Standard Practice for Making and Curing Concrete Test Specimens in the Field |
ASTM A 820/A820M : 2016 | Standard Specification for Steel Fibers for Fiber-Reinforced Concrete |
ASTM C 31/C31M : 2015 | Standard Practice for Making and Curing Concrete Test Specimens in the Field |
ASTM C 39/C39M : 2018 | Standard Test Method for Compressive Strength of Cylindrical Concrete Specimens |
ASTM C 31/C31M : 2019 | Standard Practice for Making and Curing Concrete Test Specimens in the Field |
ASTM D 6942 : 2003 | Standard Test Method for Stability of Cellulose Fibers in Alkaline Environments |
ASTM C 1399 : 2007 : REV A | Standard Test Method for Obtaining Average Residual-Strength of Fiber-Reinforced Concrete |
ASTM C 1077 : 2013 : REV B | Standard Practice for Agencies Testing Concrete and Concrete Aggregates for Use in Construction and Criteria for Testing Agency Evaluation |
ASTM C 666/C666M : 2015 | Standard Test Method for Resistance of Concrete to Rapid Freezing and Thawing (Withdrawn 2024) |
ASTM C 94/C94M : 2022 | Standard Specification for Ready-Mixed Concrete |
ASTM C 1480 : 2000 | Standard Specification for Packaged, Pre-Blended, Dry, Combined Materials for Use in Wet or Dry Shotcrete Application |
ASTM C 1077 : 2010 : REV D | Standard Practice for Laboratories Testing Concrete and Concrete Aggregates for Use in Construction and Criteria for Laboratory Evaluation |
ASTM C 1140 : 1998 | Standard Practice for Preparing and Testing Specimens from Shotcrete Test Panels |
ASTM C 1550 : 2010 : REV A | Standard Test Method for Flexural Toughness of Fiber Reinforced Concrete (Using Centrally Loaded Round Panel) |
ASTM C 1077 : 2009 | Standard Practice for Laboratories Testing Concrete and Concrete Aggregates for Use in Construction and Criteria for Laboratory Evaluation |
ASTM C 1077 : 2013 | Standard Practice for Agencies Testing Concrete and Concrete Aggregates for Use in Construction and Criteria for Testing Agency Evaluation |
ASTM C 138/C138M : 2017 : REV A | Standard Test Method for Density (Unit Weight), Yield, and Air Content (Gravimetric) of Concrete |
ASTM C 125 : 2020 | Standard Terminology Relating to Concrete and Concrete Aggregates |
ASTM C 1550 : 2012 : REV A | Standard Test Method for Flexural Toughness of Fiber Reinforced Concrete (Using Centrally Loaded Round Panel) |
ASTM C 1077 : 2011 : REV C | Standard Practice for Agencies Testing Concrete and Concrete Aggregates for Use in Construction and Criteria for Testing Agency Evaluation |
ASTM C 1077 : 2011 | Standard Practice for Agencies Testing Concrete and Concrete Aggregates for Use in Construction and Criteria for Testing Agency Evaluation |
ASTM C 1077 : 2008 : REV A | Standard Practice for Laboratories Testing Concrete and Concrete Aggregates for Use in Construction and Criteria for Laboratory Evaluation |
ASTM C 1480 : 2000 : R2005 | Standard Specification for Packaged, Pre-Blended, Dry, Combined Materials for Use in Wet or Dry Shotcrete Application |
ASTM C 150 : 2002 : REV A : EDT 1 | Standard Specification for Portland Cement |
ASTM C 1077 : 2003 : REV A | Standard Practice for Laboratories Testing Concrete and Concrete Aggregates for Use in Construction and Criteria for Laboratory Evaluation |
ASTM C 1399 : 2007 | Standard Test Method for Obtaining Average Residual-Strength of Fiber-Reinforced Concrete |
ASTM C 1399 : 2000 | Test Method for Obtaining Average Residual-Strength of Fiber-Reinforced Concrete |
ASTM C 1077 : 2005 : REV A | Standard Practice for Laboratories Testing Concrete and Concrete Aggregates for Use in Construction and Criteria for Laboratory Evaluation |
ASTM C 1436 : 1999 | Standard Specification for Materials for Shotcrete |
ACI 506.2 : 2013 | SPECIFICATION FOR SHOTCRETE |
ASTM C 1077 : 2012 | Standard Practice for Agencies Testing Concrete and Concrete Aggregates for Use in Construction and Criteria for Testing Agency Evaluation |
ASTM C 94/C94M : 2023 | Standard Specification for Ready-Mixed Concrete |
ASTM C 125 : 2009 | Standard Terminology Relating to Concrete and Concrete Aggregates |
ASTM D 7357 : 2007 | Standard Specification for Cellulose Fibers for Fiber-Reinforced Concrete |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.