![header thumbnail](/images/publishers\astm_cover.gif)
ASTM C 1157/C1157M : 2020 : REV A
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
![header thumbnail](/images/publishers\astm_cover.gif)
Standard Performance Specification for Hydraulic Cement
Hardcopy , PDF
16-10-2023
English
29-01-2021
Committee |
C 01
|
DocumentType |
Standard
|
Pages |
5
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
1.1This performance specification covers hydraulic cements for both general and special applications. There are no restrictions on the composition of the cement or its constituents (see Note 1).
Note 1:There are two related hydraulic cement standards, Specification C150/C150M for portland cement and Specifications C595/C595M for blended cements, both of which contain prescriptive and performance requirements
1.2This performance specification classifies cements based on specific requirements for general use, high early strength, resistance to attack by sulfates, and heat of hydration. Optional requirements are provided for the property of low reactivity with alkali-silica-reactive aggregates and for air-entraining cements.
1.3The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. Values in SI units [or inch-pound units] shall be obtained by measurement in SI units [or inch-pound units] or by appropriate conversion, using the Rules for Conversion and Rounding given in IEEE/ASTM SI 10, of measurements made in other units [or SI units]. Values are stated in only SI units when inch-pound units are not used in practice.
1.4The text of this performance specification refers to notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) are not requirements of the standard.
1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM C 1372 : 2022 | Standard Specification for Dry-Cast Segmental Retaining Wall Units |
ASTM C 183/C183M : 2023 | Standard Practice for Sampling and the Amount of Testing of Hydraulic Cement |
ASTM C 139 : 2022 | Standard Specification for Concrete Masonry Units for Construction of Catch Basins and Manholes |
ASTM C 1319 : 2023 | Standard Specification for Concrete Grid Paving Units |
ASTM C 1778 : 2022 | Standard Guide for Reducing the Risk of Deleterious Alkali-Aggregate Reaction in Concrete |
ASTM C 936/C936M : 2023 | Standard Specification for Solid Concrete Interlocking Paving Units |
ASTM C 595/C595M : 2023 | Standard Specification for Blended Hydraulic Cements |
ASTM C 1782/C1782M : 2023 | Standard Specification for Segmental Concrete Paving Slabs |
ASTM C 476 : 2023 | Standard Specification for Grout for Masonry |
ASTM C 1713 : 2023 | Standard Specification for Mortars for the Repair of Historic Masonry |
ASTM C 1884 : 2023 | Standard Specification for Manufactured Concrete Ballast Units |
ASTM C 1634 : 2023 | Standard Specification for Concrete Facing Brick and Other Concrete Masonry Facing Units |
ASTM C 1623 : 2022 | Standard Specification for Manufactured Concrete Masonry Lintels |
ASTM C 1492 : 2022 | Standard Specification for Concrete Roof Tile |
ASTM C 226 : 2022 | Standard Specification for Air-Entraining Additions for Use in the Manufacture of Air-Entraining Hydraulic Cement |
ASTM C 1776/C1776M : 2017 : R2022 | Standard Specification for Wet-Cast Precast Modular Retaining Wall Units |
ASTM C 913 : 2021 | Standard Specification for Precast Concrete Water and Wastewater Structures |
ASTM C 465 : 2023 | Standard Specification for Processing Additions for Use in the Manufacture<brk/> of Hydraulic Cements |
ASTM C 55 : 2022 | Standard Specification for Concrete Building Brick |
ASTM C 1837 : 2022 | Standard Specification for Production of Dry Cast Concrete Used for Manufacturing Pipe, Box, and Precast Structures |
ASTM C 1227 : 2023 | Standard Specification for Precast Concrete Septic Tanks |
ASTM C 1731 : 2021 | Standard Specification for Concrete Floor Tile |
ASTM C 129 : 2022 | Standard Specification for Nonloadbearing Concrete Masonry Units |
ASTM C 1670/C1670M : 2023 | Standard Specification for Adhered Manufactured Stone Masonry Veneer Units |
ASTM C 90 : 2022 | Standard Specification for Loadbearing Concrete Masonry Units |
ASTM C 1904 : 2022 | Standard Test Methods for Determination of the Effects of Biogenic Acidification on Concrete Antimicrobial Additives and/or Concrete Products |
ASTM C 94/C94M : 2023 | Standard Specification for Ready-Mixed Concrete |
ASTM C 387/C387M : 2023 | Standard Specification for Packaged, Dry, Combined Materials for Concrete and High Strength Mortar |
ASTM C 1364 : 2023 | Standard Specification for Architectural Cast Stone |
ASTM C 1222 : 2023 | Standard Practice for Evaluation of Laboratories Testing Hydraulic Cement |
ASTM C 595/C595M : 2020 | Standard Specification for Blended Hydraulic Cements |
ASTM C 1731 : 2016 | Standard Specification for Concrete Floor Tile |
ASTM C 1688/C1688M : 2014 : REV A | Standard Test Method for Density and Void Content of Freshly Mixed Pervious Concrete (Withdrawn 2023) |
ASTM C 94/C94M : 2020 | Standard Specification for Ready-Mixed Concrete |
ASTM C 1707 : 2018 | Standard Specification for Pozzolanic Hydraulic Lime for Structural Purposes |
ASTM C 913 : 2018 | Standard Specification for Precast Concrete Water and Wastewater Structures |
ASTM C 465 : 2019 | Standard Specification for Processing Additions for Use in the Manufacture<brk/> of Hydraulic Cements |
ASTM C 1491 : 2019 | Standard Specification for Concrete Roof Pavers (Withdrawn 2023) |
ASTM C 1778 : 2020 | Standard Guide for Reducing the Risk of Deleterious Alkali-Aggregate Reaction in Concrete |
ASTM C 1804 : 2020 | Standard Specification for Spun Cast Prestressed Concrete Bases for Tapered Steel Lighting Poles |
ASTM C 1634 : 2020 | Standard Specification for Concrete Facing Brick and Other Concrete Masonry Facing Units |
ASTM C 1670/C1670M : 2021 | Standard Specification for Adhered Manufactured Stone Masonry Veneer Units |
ASTM C 476 : 2020 | Standard Specification for Grout for Masonry |
ASTM C 109/C109M : 2020 : REV B | Standard Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 2-in. or [50mm] Cube Specimens) |
ASTM C 185 : 2020 | Standard Test Method for Air Content of Hydraulic Cement Mortar |
ASTM C 936/C936M : 2020 | Standard Specification for Solid Concrete Interlocking Paving Units |
ASTM C 1884 : 2019 | Standard Specification for Concrete Ballast Block |
ASTM C 1012/C1012M : 2018 : REV B | Standard Test Method for Length Change of Hydraulic-Cement Mortars Exposed to a Sulfate Solution |
ASTM C 1782/C1782M : 2020 : REV A | Standard Specification for Segmental Concrete Paving Slabs |
ASTM C 1904 : 2020 | Standard Test Methods for Determination of the Effects of Biogenic Acidification on Concrete Antimicrobial Additives and/or Concrete Products |
ASTM C 685/C685M : 2017 | Standard Specification for Concrete Made by Volumetric Batching and Continuous Mixing |
ASTM C 183/C183M : 2016 | Standard Practice for Sampling and the Amount of Testing of Hydraulic Cement |
ASTM C 226 : 2019 | Standard Specification for Air-Entraining Additions for Use in the Manufacture of Air-Entraining Hydraulic Cement |
ASTM C 887 : 2020 | Standard Specification for Packaged, Dry, Combined Materials for Surface Bonding Mortar |
ASTM C 1240 : 2020 | Standard Specification for Silica Fume Used in Cementitious Mixtures |
ASTM C 563 : 2020 | Standard Guide for Approximation of Optimum SO<inf>3</inf> in Hydraulic Cement |
ASTM C 90 : 2016 : REV A | Standard Specification for Loadbearing Concrete Masonry Units |
ASTM C 1903 : 2021 | Standard Specification for Precast Concrete Duct Bank |
ASTM C 1837 : 2017 | Standard Specification for Production of Dry Cast Concrete Used for Manufacturing Pipe, Box, and Precast Structures |
ASTM C 151/C151M : 2018 | Standard Test Method for Autoclave Expansion of Hydraulic Cement |
ASTM C 1846/C1846M : 2019 | Standard Specification for Performance Based Manufacture of Reinforced Concrete Culvert, Storm Drain, and Sewer Pipe |
ASTM C 1581/C1581M : 2018 : REV A | Standard Test Method for Determining Age at Cracking and Induced Tensile Stress Characteristics of Mortar and Concrete under Restrained Shrinkage |
ASTM C 1776/C1776M : 2017 | Standard Specification for Wet-Cast Precast Modular Retaining Wall Units |
ASTM C 183/C183M : 2016 | Standard Practice for Sampling and the Amount of Testing of Hydraulic Cement |
ASTM C 451 : 2019 | Standard Test Method for Early Stiffening of Hydraulic Cement (Paste Method) |
ASTM C 191 : 2019 | Standard Test Methods for Time of Setting of Hydraulic Cement by Vicat Needle |
ASTM C 595/C595M : 2021 | Standard Specification for Blended Hydraulic Cements |
ASTM C 188 : 2017 | Standard Test Method for Density of Hydraulic Cement |
ASTM C 109/C109M : 2021 | Standard Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 2-in. or [50mm] Cube Specimens) |
ASTM C 185 : 2015 : REV A | Standard Test Method for Air Content of Hydraulic Cement Mortar |
ASTM C 191 : 2018 : REV A | Standard Test Methods for Time of Setting of Hydraulic Cement by Vicat Needle |
ASTM C 183/C183M : 2022 | Standard Practice for Sampling and the Amount of Testing of Hydraulic Cement |
ASTM C 595/C595M : 2020 | Standard Specification for Blended Hydraulic Cements |
ASTM C 359 : 2021 | Standard Test Method for Early Stiffening of Hydraulic-Cement (Mortar Method) |
ASTM C 451 : 2021 | Standard Test Method for Early Stiffening of Hydraulic Cement (Paste Method) |
ASTM C 109/C109M : 2020 : REV A | Standard Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 2-in. or [50-mm] Cube Specimens) |
ASTM C 150/C150M : 2021 | Standard Specification for Portland Cement |
ASTM C 204 : 2023 | Standard Test Methods for Fineness of Hydraulic Cement by Air-Permeability Apparatus |
ASTM C 1702 : 2017 | Standard Test Method for Measurement of Heat of Hydration of Hydraulic Cementitious Materials Using Isothermal Conduction Calorimetry |
ASTM C 191 : 2021 | Standard Test Methods for Time of Setting of Hydraulic Cement by Vicat Needle |
ASTM C 359 : 2020 | Standard Test Method for Early Stiffening of Hydraulic-Cement (Mortar Method) |
ASTM C 109/C109M : 2016 : REV A | Standard Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 2-in. or [50-mm] Cube Specimens) |
ASTM C 114 : 2009 | Standard Test Methods for Chemical Analysis of Hydraulic Cement |
ASTM C 595/C595M : 2023 | Standard Specification for Blended Hydraulic Cements |
ASTM C 188 : 2017 : R2023 | Standard Test Method for Density of Hydraulic Cement |
ASTM C 183/C183M : 2023 | Standard Practice for Sampling and the Amount of Testing of Hydraulic Cement |
ASTM C 204 : 2018 : EDT 1 | Standard Test Methods for Fineness of Hydraulic Cement by Air-Permeability Apparatus |
ASTM C 150/C150M : 2020 | Standard Specification for Portland Cement |
ASTM C 1702 : 2009 | Standard Test Method for Measurement of Heat of Hydration of Hydraulic Cementitious Materials Using Isothermal Conduction Calorimetry |
ASTM C 150/C150M : 2022 | Standard Specification for Portland Cement |
ASTM C 1702 : 2023 | Standard Test Method for Measurement of Heat of Hydration of Hydraulic Cementitious Materials Using Isothermal Conduction Calorimetry |
ASTM C 114 : 2018 | Standard Test Methods for Chemical Analysis of Hydraulic Cement |
ASTM C 114 : 2022 | Standard Test Methods for Chemical Analysis of Hydraulic Cement |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.