ASTM C 1313/C1313M : 2013
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Sheet Radiant Barriers for Building Construction Applications
Hardcopy , PDF
23-10-2019
English
01-03-2013
Important note : Users cannot be edited or removed once added to your Multi user PDF.This specification covers the general physical property requirements of radiant barrier materials for use in building construction.
| Committee |
C 16
|
| DocumentType |
Standard
|
| Pages |
4
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This specification covers the general physical property requirements of radiant barrier materials for use in building construction. The scope is specifically limited to requirements for radiant barrier sheet materials that consist of at least one surface having a far-infrared emittance of 0.1 or less, such as metallic foils or metallic deposits mounted or unmounted on substrates.
1.2The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.3The following safety hazards caveat pertains only to the test methods (Section 10) described in this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| ASTM C 1743 : 2010 | Standard Practice for Installation and Use of Radiant Barrier Systems (RBS) in Residential Building Construction |
| ASTM C 1371 : 2004 : REV A : R2010 : EDT 1 | Standard Test Method for Determination of Emittance of Materials Near Room Temperature Using Portable Emissometers |
| ASTM D 2261 : 2007 | Standard Test Method for Tearing Strength of Fabrics by the Tongue (Single Rip) Procedure (Constant-Rate-of-Extension Tensile Testing Machine) |
| ASTM E 2599 : 2009 | Standard Practice for Specimen Preparation and Mounting of Reflective Insulation Materials and Radiant Barrier Materials for Building Applications to Assess Surface Burning Characteristics |
| ASTM C 1744 : 2012 | Standard Practice for Installation and Use of Radiant Barrier Systems (RBS) in Commercial/Industrial Building Construction |
| ASTM C 1338 : 2000 | Standard Test Method for Determining Fungi Resistance of Insulation Materials and Facings |
| ASTM D 2261 : 2011 | Standard Test Method for Tearing Strength of Fabrics by the Tongue (Single Rip) Procedure (Constant-Rate-of-Extension Tensile Testing Machine) |
| ASTM D 2261 : 2007 : REV A : EDT 1 | Standard Test Method for Tearing Strength of Fabrics by the Tongue (Single Rip) Procedure (Constant-Rate-of-Extension Tensile Testing Machine) |
| ASTM D 2261 : 2007 : REV A | Standard Test Method for Tearing Strength of Fabrics by the Tongue (Single Rip) Procedure (Constant-Rate-of-Extension Tensile Testing Machine) |
| ASTM D 3310 : 2000 : R2006 | Standard Test Method for Determining Corrosivity of Adhesive Materials |
| ASTM C 1371 : 1998 | Standard Test Method for Determination of Emittance of Materials Near Room Temperature Using Portable Emissometers |
| ASTM C 1338 : 2014 | Standard Test Method for Determining Fungi Resistance of Insulation Materials and Facings |
| ASTM C 1744 : 2010 | Standard Practice for Installation and Use of Radiant Barrier Systems (RBS) in Commercial/Industrial Building Construction |
| ASTM C 1338 : 2019 | Standard Test Method for Determining Fungi Resistance of Insulation Materials and Facings |
| ASTM C 1338 : 2008 | Standard Test Method for Determining Fungi Resistance of Insulation Materials and Facings |
| ASTM E 2599 : 2015 | Standard Practice for Specimen Preparation and Mounting of Reflective Insulation, Radiant Barrier and Vinyl Stretch Ceiling Materials for Building Applications to Assess Surface Burning Characteristics |
| ASTM E 2599 : 2016 | Standard Practice for Specimen Preparation and Mounting of Reflective Insulation, Radiant Barrier and Vinyl Stretch Ceiling Materials for Building Applications to Assess Surface Burning Characteristics |
| ASTM D 2261 : 1996 | Standard Test Method for Tearing Strength of Fabrics by the Tongue (Single Rip) Procedure (Constant-Rate-of-Extension Tensile Testing Machine) |
| ASTM D 3310 : 2000 | Standard Test Method for Determining Corrosivity of Adhesive Materials |
| ASTM C 1743 : 2018 | Standard Practice for Installation and Use of Radiant Barrier Systems (RBS) in Residential Building Construction |
| ASTM E 2599 : 2010 | Standard Practice for Specimen Preparation and Mounting of Reflective Insulation, Radiant Barrier and Vinyl Stretch Ceiling Materials for Building Applications to Assess Surface Burning Characteristics |
| ASTM C 1743 : 2019 | Standard Practice for Installation and Use of Radiant Barrier Systems (RBS) in Residential Building Construction |
| ASTM C 1371 : 2004 | Standard Test Method for Determination of Emittance of Materials Near Room Temperature Using Portable Emissometers |
| ASTM E 2599 : 2011 | Standard Practice for Specimen Preparation and Mounting of Reflective Insulation, Radiant Barrier and Vinyl Stretch Ceiling Materials for Building Applications to Assess Surface Burning Characteristics |
| ASTM D 3310 : 2000 : R2014 | Standard Test Method for Determining Corrosivity of Adhesive Materials |
| ASTM D 2261 : 2013 | Standard Test Method for Tearing Strength of Fabrics by the Tongue (Single Rip) Procedure (Constant-Rate-of-Extension Tensile Testing Machine) |
| ASTM D 2261 : 2013 : R2017 : EDT 1 | Standard Test Method for Tearing Strength of Fabrics by the Tongue (Single Rip) Procedure (Constant-Rate-of-Extension Tensile Testing Machine) |
| ASTM C 1371 : 2004 : REV A | Standard Test Method for Determination of Emittance of Materials Near Room Temperature Using Portable Emissometers |
| ASTM D 2261 : 2013 : R2017 | Standard Test Method for Tearing Strength of Fabrics by the Tongue (Single Rip) Procedure (Constant-Rate-of-Extension Tensile Testing Machine) |
| ASTM C 1743 : 2012 | Standard Practice for Installation and Use of Radiant Barrier Systems (RBS) in Residential Building Construction |
| ASTM E 2599 : 2018 | Standard Practice for Specimen Preparation and Mounting of Reflective Insulation, Radiant Barrier and Vinyl Stretch Ceiling Materials for Building Applications to Assess Surface Burning Characteristics |
| ASTM C 1371 : 2015 | Standard Test Method for Determination of Emittance of Materials Near Room Temperature Using Portable Emissometers |
| ASTM E 2599 : 2009 : REV A | Standard Practice for Specimen Preparation and Mounting of Reflective Insulation Materials and Radiant Barrier Materials for Building Applications to Assess Surface Burning Characteristics |
| ASTM D 2261 : 1996 : R2002 | Standard Test Method for Tearing Strength of Fabrics by the Tongue (Single Rip) Procedure (Constant-Rate-of-Extension Tensile Testing Machine) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.