ASTM C 1329 : 2005
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Mortar Cement
Hardcopy , PDF
11-11-2014
English
15-09-2005
Important note : Users cannot be edited or removed once added to your Multi user PDF.CONTAINED IN VOL. 04.01, 2011 Specifies the three types of mortar cement used where mortar for masonry is required.
| Committee |
C 01
|
| DocumentType |
Standard
|
| Pages |
4
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1 This specification covers three types of mortar cement for use where mortar for masonry is required.
1.2 The values stated in SI units are to be regarded as the standard. Values in SI units shall be obtained by measurement in SI units or by appropriate conversion, using the Rules for Conversion and Rounding given in IEEE/ASTM SI 10, of measurements made in other units.
1.3 The text of this standard refers to notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.
1.4 The following safety hazards caveat pertains only to Annex A1. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. (Warning—Fresh hydraulic cementitious mixtures are caustic and may cause chemical burns to skin and tissue upon prolonged exposure.)
| ASTM C 1722 : 2011 | Standard Guide for Repair and Restoration of Dimension Stone |
| ASTM C 1660 : 2010 : R2018 | Standard Specification for Thin-bed Mortar for Autoclaved Aerated Concrete (AAC) Masonry |
| ASTM C 387/C387M : 2017 : REDLINE | Standard Specification for Packaged, Dry, Combined Materials for Concrete and High Strength Mortar |
| ASTM C 1713 : 2017 : REDLINE | Standard Specification for Mortars for the Repair of Historic Masonry |
| ASTM C 1713 : 2017 | Standard Specification for Mortars for the Repair of Historic Masonry |
| ASTM C 185 : 2015 : REV A | Standard Test Method for Air Content of Hydraulic Cement Mortar |
| ASTM C 387/C387M : 2017 | Standard Specification for Packaged, Dry, Combined Materials for Concrete and High Strength Mortar |
| ASTM C 109/C109M : 2016 : REV A | Standard Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 2-in. or [50-mm] Cube Specimens) |
| ASTM C 1660 : 2010 | Standard Specification for Thin-bed Mortar for Autoclaved Aerated Concrete (AAC) Masonry |
| ASTM C 151 : 2005 | Standard Test Method for Autoclave Expansion of Hydraulic Cement |
| ASTM C 305 : 2014 : REDLINE | Standard Practice for Mechanical Mixing of Hydraulic Cement Pastes and Mortars of Plastic Consistency |
| ASTM C 91 : 2005 | Standard Specification for Masonry Cement |
| ASTM C 187 : 2016 : REDLINE | Standard Test Method for Amount of Water Required for Normal Consistency of Hydraulic Cement Paste |
| IEEE/ASTM SI_10-2010 | American National Standard for Metric Practice |
| ASTM C 778 : 2017 : REDLINE | Standard Specification for Standard Sand |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.