ASTM C 1478 : 2019
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Storm Drain Resilient Connectors Between Reinforced Concrete Storm Sewer Structures, Pipes, and Laterals
Hardcopy , PDF
15-09-2020
English
01-03-2019
Important note : Users cannot be edited or removed once added to your Multi user PDF.1.1 This specification covers the minimum performance and material requirements for resilient connectors used for connections between precast reinforced concrete storm sewer structures conforming to Specification C478 and pipes, and between precast reinforced concrete pipe and laterals for storm drainage systems.
| Committee |
C 13
|
| DocumentType |
Standard
|
| Pages |
3
|
| ProductNote |
THIS STANDARD ALSO REFERS TO C822,C913,D395
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This specification covers the minimum performance and material requirements for resilient connectors used for connections between precast reinforced concrete storm sewer structures conforming to Specification C478 and pipes, and between precast reinforced concrete pipe and laterals for storm drainage systems.
1.1.1These connectors are designed to prevent soil migration between the pipe and storm sewer structure, and between the pipe and lateral.
1.2The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are for information only.
Note 1:This specification covers the design, material, and performance of the resilient connection only. Connections covered by this specification are adequate for hydrostatic pressures up to 6 psi (14 ft) without leakage when tested in accordance with Section 7. Infiltration quantities for an installed system are dependent upon many factors other than the connections between storm sewer structures and pipe, and allowable quantities must be covered by other specifications and suitable testing of the installed pipeline and system.
Note 2:For installations that exceed 6 psi (14 ft), the user is cautioned to verify the amount of hydrostatic head pressure the connector will experience. If the total pressure applied to the connector exceeds the 6 psi limits of the specification, the user is advised to contact the connector manufacturer for alternative methods of connecting the pipe, or applicable alternative standards.
1.3The following precautionary caveat pertains only to the test methods portion, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For a specific warning statement, see 7.2.4.
1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM C 1821/C1821M : 2016 | Standard Practice for Installation of Underground Circular Precast Concrete Manhole Structures |
| ASTM D 1566 : 2004 : REV A | Standard Terminology Relating to Rubber |
| ASTM D 2240 : 2000 | Standard Test Method for Rubber Property—Durometer Hardness |
| ASTM D 1566 : 2009 | Standard Terminology Relating to Rubber |
| ASTM D 2137 : 2011 : R2018 | Standard Test Methods for Rubber Property—Brittleness Point of Flexible Polymers and Coated Fabrics |
| ASTM D 1566 : 2006 | Standard Terminology Relating to Rubber |
| ASTM D 1566 : 2008 : REV A | Standard Terminology Relating to Rubber |
| ASTM D 1149 : 2016 | Standard Test Methods for Rubber Deterioration—Cracking in an Ozone Controlled Environment |
| ASTM D 2137 : 1994 : R2000 | Standard Test Methods for Rubber Property-Brittleness Point of Flexible Polymers and Coated Fabrics |
| ASTM D 1566 : 2005 | Standard Terminology Relating to Rubber |
| ASTM D 1566 : 2002 : REV A | Standard Terminology Relating to Rubber |
| ASTM D 1566 : 2007 | Standard Terminology Relating to Rubber |
| ASTM D 1566 : 2019 | Standard Terminology Relating to Rubber |
| ASTM D 2240 : 2004 | Standard Test Method for Rubber Property—Durometer Hardness |
| ASTM D 1566 : 2015 | Standard Terminology Relating to Rubber |
| ASTM D 1566 : 2008 | Standard Terminology Relating to Rubber |
| ASTM D 1149 : 2015 | Standard Test Methods for Rubber Deterioration—Cracking in an Ozone Controlled Environment |
| ASTM D 1566 : 2005 : REV A | Standard Terminology Relating to Rubber |
| ASTM D 1149 : 2007 | Standard Test Methods for Rubber Deterioration-Cracking in an Ozone Controlled Environment |
| ASTM D 2240 : 2004 : EDT 1 | Standard Test Method for Rubber Property—Durometer Hardness |
| ASTM D 1566 : 2006 : REV A | Standard Terminology Relating to Rubber |
| ASTM D 1566 : 2003 : REV A | Standard Terminology Relating to Rubber |
| ASTM D 1566 : 2006 : REV B | Standard Terminology Relating to Rubber |
| ASTM D 2137 : 2010 | Standard Test Methods for Rubber Property-Brittleness Point of Flexible Polymers and Coated Fabrics |
| ASTM D 1566 : 2005 : REV B | Standard Terminology Relating to Rubber |
| ASTM D 1149 : 2018 | Standard Test Methods for Rubber Deterioration—Cracking in an Ozone Controlled Environment |
| ASTM D 1566 : 2011 | Standard Terminology Relating to Rubber |
| ASTM D 2137 : 2005 | Standard Test Methods for Rubber Property-Brittleness Point of Flexible Polymers and Coated Fabrics |
| ASTM D 1566 : 2000 : REV B | Standard Terminology Relating to Rubber |
| ASTM D 2240 : 2002 | Standard Test Method for Rubber Property—Durometer Hardness |
| ASTM D 1566 : 2014 | Standard Terminology Relating to Rubber |
| ASTM D 2240 : 2015 | Standard Test Method for Rubber Property—Durometer Hardness |
| ASTM D 1149 : 2007 : R2012 | Standard Test Methods for Rubber Deterioration—Cracking in an Ozone Controlled Environment |
| ASTM D 2240 : 2003 | Standard Test Method for Rubber Property—Durometer Hardness |
| ASTM D 1149 : 1978 : REV A | Standard Test Method for Rubber Deterioration - Surface Ozone Cracking In A Chamber ( Flat Specimen) |
| ASTM D 1566 : 2010 | Standard Terminology Relating to Rubber |
| ASTM D 2240 : 2002 : REV B | Standard Test Method for Rubber Property—Durometer Hardness |
| ASTM D 2240 : 2015 : EDT 1 | Standard Test Method for Rubber Property—Durometer Hardness |
| ASTM D 1566 : 2003 | Standard Terminology Relating to Rubber |
| ASTM D 1566 : 2000 | Standard Terminology Relating to Rubber |
| ASTM D 2240 : 2005 | Standard Test Method for Rubber Property—Durometer Hardness |
| ASTM D 2240 : 2005 : R2010 | Standard Test Method for Rubber Property—Durometer Hardness |
| ASTM D 1566 : 2007 : REV A | Standard Terminology Relating to Rubber |
| ASTM D 1566 : 2005 : REV C | Standard Terminology Relating to Rubber |
| ASTM D 2240 : 2002 : REV A | Standard Test Method for Rubber Property—Durometer Hardness |
| ASTM D 1566 : 2010 : EDT 1 | Standard Terminology Relating to Rubber |
| ASTM D 1149 : 1999 | Standard Test Method for Rubber Deterioration-Surface Ozone Cracking in a Chamber |
| ASTM D 2137 : 2011 | Standard Test Methods for Rubber Property<char: emdash>Brittleness Point of Flexible Polymers and Coated Fabrics |
| ASTM D 1566 : 2008 : REV B | Standard Terminology Relating to Rubber |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.