ASTM C 1581/C1581M : 2018 : REV A
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Determining Age at Cracking and Induced Tensile Stress Characteristics of Mortar and Concrete under Restrained Shrinkage
Hardcopy , PDF
19-08-2024
English
01-07-2018
1.1This test method covers the laboratory determination of the age at cracking and induced tensile stress characteristics of mortar or concrete specimens under restrained shrinkage.
Committee |
C 09
|
DocumentType |
Test Method
|
Pages |
7
|
ProductNote |
THIS STANDARD ALSO REFRS TO C33/C33M, C150/C150M, C595/C595M, F441/F441M
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
1.1This test method covers the laboratory determination of the age at cracking and induced tensile stress characteristics of mortar or concrete specimens under restrained shrinkage. The procedure can be used to determine the effects of variations in the proportions and material properties of mortar or concrete on cracking due to both drying shrinkage and deformations caused by autogenous shrinkage and heat of hydration.
1.2This test method is not intended for expansive materials.
1.3The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.(Warning—Fresh hydraulic cementitious mixtures are caustic and may cause chemical burns to skin and tissue upon prolonged exposure.2)
1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM C 125 : 2021 | Standard Terminology Relating to Concrete and Concrete Aggregates |
ASTM C 150/C150M : 2024 | Standard Specification for Portland Cement |
ASTM C 1437 : 2001 | Standard Test Method for Flow of Hydraulic Cement Mortar |
ASTM C 138/C138M : 2014 | Standard Test Method for Density (Unit Weight), Yield, and Air Content (Gravimetric) of Concrete |
ASTM C 33/C33M : 2023 | Standard Specification for Concrete Aggregates |
ASTM C 387/C387M : 2017 | Standard Specification for Packaged, Dry, Combined Materials for Concrete and High Strength Mortar |
ASTM C 138/C138M : 2023 | Standard Test Method for Density (Unit Weight), Yield, and Air Content (Gravimetric) of Concrete |
ASTM C 33/C33M : 2018 | Standard Specification for Concrete Aggregates |
ASTM C 1437 : 2013 | Standard Test Method for Flow of Hydraulic Cement Mortar |
ASTM C 595/C595M : 2021 | Standard Specification for Blended Hydraulic Cements |
ASTM C 1157/C1157M : 2023 | Standard Performance Specification for Hydraulic Cement |
ASTM C 192/C192M : 2000 | Standard Practice for Making and Curing Concrete Test Specimens in the Laboratory |
ASTM C 138/C138M : 2024 : REV A | Standard Test Method for Density (Unit Weight), Yield, and Air Content (Gravimetric) of Concrete |
ASTM C 125 : 2000 | Standard Terminology Relating to Concrete and Concrete Aggregates |
ASTM C 595/C595M : 2020 | Standard Specification for Blended Hydraulic Cements |
ASTM C 1157/C1157M : 2020 | Standard Performance Specification for Hydraulic Cement |
ASTM C 138/C138M : 2024 | Standard Test Method for Density (Unit Weight), Yield, and Air Content (Gravimetric) of Concrete |
ASTM C 150/C150M : 2021 | Standard Specification for Portland Cement |
ASTM C 1157/C1157M : 2020 : REV A | Standard Performance Specification for Hydraulic Cement |
ASTM F 441/F441M : 2020 | Standard Specification for Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Pipe, Schedules 40 and 80 |
ASTM C 143/C143M : 2015 : REV A | Standard Test Method for Slump of Hydraulic-Cement Concrete |
ASTM F 441/F441M : 2023 | Standard Specification for Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Pipe, Schedules 40 and 80 |
ASTM C 387/C387M : 2023 | Standard Specification for Packaged, Dry, Combined Materials for Concrete and High Strength Mortar |
ASTM C 595/C595M : 2024 | Standard Specification for Blended Hydraulic Cements |
ASTM C 125 : 2021 : REV A | Standard Terminology Relating to Concrete and Concrete Aggregates |
ASTM C 595/C595M : 2023 | Standard Specification for Blended Hydraulic Cements |
ASTM C 1437 : 2007 | Standard Test Method for Flow of Hydraulic Cement Mortar |
ASTM C 138/C138M : 2017 : REV A | Standard Test Method for Density (Unit Weight), Yield, and Air Content (Gravimetric) of Concrete |
ASTM C 150/C150M : 2020 | Standard Specification for Portland Cement |
ASTM C 125 : 2020 | Standard Terminology Relating to Concrete and Concrete Aggregates |
ASTM C 1437 : 2015 | Standard Test Method for Flow of Hydraulic Cement Mortar |
ASTM C 150/C150M : 2022 | Standard Specification for Portland Cement |
ASTM C 1437 : 1999 | Standard Test Method for Flow of Hydraulic Cement Mortar |
ASTM C 125 : 2009 | Standard Terminology Relating to Concrete and Concrete Aggregates |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.