ASTM C 172/C172M : 2017
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Practice for Sampling Freshly Mixed Concrete
English
01-10-2017
15-10-2025
This practice covers procedures for obtaining representative samples of fresh concrete as delivered to the project site on which tests are to be performed to determine compliance with quality requirements of the specifications under which the concrete is furnished (Note 1).
| Committee |
C 09
|
| DocumentType |
Standard Practice
|
| Pages |
3
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This practice covers procedures for obtaining representative samples of fresh concrete as delivered to the project site on which tests are to be performed to determine compliance with quality requirements of the specifications under which the concrete is furnished (Note 1). The practice includes sampling from stationary, paving and truck mixers, and from agitating and nonagitating equipment used to transport central-mixed concrete and from continuous mixing equipment as described in Specification C685/C685M.
1.2The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
Note 1:Composite samples are required by this practice, unless specifically excepted by procedures governing the tests to be performed such as tests to determine uniformity of consistency and mixer efficiency. Procedures used to select the specific test batches are not described in this practice, but it is recommended that random sampling be used to determine overall specification compliance.
1.3This practice also covers the procedures to be used for preparing a sample of concrete for further testing where it is desirable or necessary to remove the aggregate larger than a designated size. This removal of larger aggregate particles is preferably accomplished by wet-sieving.
1.4The text of this standard references notes and footnotes which provide explanatory material and shall not be considered as requirements of the practice.
1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. (Warning—Fresh hydraulic cementitious mixtures are caustic and may cause chemical burns to skin and tissue upon prolonged exposure.2)
1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM C 1768/C1768M : 2025 | Standard Practice for Accelerated Curing of Concrete Cylinders |
| ASTM D 3665 : 2024 | Standard Practice for Random Sampling of Construction Materials |
| ASTM C 231/C231M : 2024 | Standard Test Method for Air Content of Freshly Mixed Concrete by the Pressure Method |
| ASTM C 143/C143M : 2020 | Standard Test Method for Slump of Hydraulic-Cement Concrete |
| ASTM C 1890 : 2019 : R2025 | Standard Test Method for K-slump of Freshly Mixed Concrete |
| ASTM D 5971/D5971M : 2025 | Standard Practice for Sampling Freshly Mixed Controlled Low-Strength Material |
| ASTM C 232/C232M : 2021 | Standard Test Method for Bleeding of Concrete |
| ASTM C 1679 : 2022 | Standard Practice for Measuring Hydration Kinetics of Hydraulic Cementitious Mixtures Using Isothermal Calorimetry |
| ASTM C 1731 : 2021 | Standard Specification for Concrete Floor Tile |
| ASTM C 1688/C1688M : 2025 | Standard Test Method for Density and Void Content of Freshly Mixed Pervious Concrete |
| ASTM C 1435/C1435M : 2020 | Standard Practice for Molding Roller-Compacted Concrete in Cylinder Molds Using a Vibrating Hammer |
| ASTM C 1090/C1090M : 2023 | Standard Test Method for Measuring Changes in Height of Cylindrical Specimens of Hydraulic-Cement Grout |
| ASTM C 157/C157M : 2024 : EDT 1 | Standard Test Method for Length Change of Hardened Hydraulic-Cement Mortar and Concrete |
| ASTM C 233/C233M : 2024 | Standard Test Method for Air-Entraining Admixtures for Concrete |
| ASTM C 138/C138M : 2024 : REV A | Standard Test Method for Density (Unit Weight), Yield, and Air Content (Gravimetric) of Concrete |
| ASTM C 94/C94M : 2025 | Standard Specification for Ready-Mixed Concrete |
| ASTM C 935 : 2019 : R2025 | Standard Specification for General Requirements for Prestressed Concrete Poles Statically Cast |
| ASTM C 495/C495M : 2012 : R2019 | Standard Test Method for Compressive Strength of Lightweight Insulating Concrete |
| ASTM C 1712 : 2024 | Standard Test Method for Rapid Assessment of Static Segregation Resistance of Self-Consolidating Concrete Using Penetration Test |
| ASTM F 3706 : 2024 | Standard Practice for In Field Spray Applied Mortar Linings for Large Diameter Stormwater and Sewer Conduits |
| ASTM C 31/C31M : 2025 : REV B | Standard Practice for Making and Curing Concrete Test Specimens in the Field |
| ASTM C 1089 : 2019 : R2025 | Standard Specification for Spun Cast Prestressed Concrete Poles |
| ASTM C 1116/C1116M : 2023 | Standard Specification for Fiber-Reinforced Concrete |
| ASTM C 1611/C1611M : 2021 | Standard Test Method for Slump Flow of Self-Consolidating Concrete |
| ASTM C 403/C403M : 2023 | Standard Test Method for Time of Setting of Concrete Mixtures by Penetration Resistance |
| ASTM C 1610/C1610M : 2024 | Standard Test Method for Static Segregation of Self-Consolidating Concrete Using Column Technique |
| ASTM C 1609/C1609M : 2024 | Standard Test Method for Flexural Performance of Fiber-Reinforced Concrete (Using Beam With Third-Point Loading) |
| ASTM C 192/C192M : 2025 | Standard Practice for Making and Curing Concrete Test Specimens in the Laboratory |
| ASTM C 1064/C1064M : 2023 | Standard Test Method for Temperature of Freshly Mixed Hydraulic-Cement Concrete |
| ASTM C 1849/C1849M : 2023 | Standard Test Method for Density and Air Content (Pressure Method) of Freshly Mixed Roller-Compacted Concrete |
| ASTM C 1077 : 2025 : REV A | Standard Practice for Agencies Testing Concrete and Concrete Aggregates for Use in Construction and Criteria for Testing Agency Evaluation |
| ASTM C 1753/C1753M : 2021 : REV A | Standard Practice for Evaluating Early Hydration of Hydraulic Cementitious Mixtures Using Thermal Measurements |
| ASTM D 6103/D6103M : 2017 : EDT 1 | Standard Test Method for Flow Consistency of Controlled Low Strength Material (CLSM) |
| ASTM C 1804 : 2020 : R2025 | Standard Specification for Spun Cast Prestressed Concrete Bases for Tapered Steel Lighting Poles |
| ACI CODE-350:2020 | Code Requirements for Environmental Engineering Concrete Structures (ACI 350-20) and Commentary (ACI 350R-20)<br> |
| AASHTO T 197M/T 197 : 2011(R2019) | METHOD OF TEST FOR TIME OF SETTING OF CONCRETE MIXTURES BY PENETRATION RESISTANCE |
| ICC IBC INTERNATIONAL BUILDING CODE:2021 | International Building Code |
| ACI 311.6 :2018 | Specification for Testing Ready-Mixed Concrete |
| ACI SPEC-522.1:2020 | Specification for Construction of Pervious Concrete Pavement |
| ASTM E 11 : 2020 | Standard Specification for Woven Wire Test Sieve Cloth and Test Sieves |
| ASTM C 685/C685M : 2017 | Standard Specification for Concrete Made by Volumetric Batching and Continuous Mixing |
| ASTM E 11 : 2024 | Standard Specification for Woven Wire Test Sieve Cloth and Test Sieves |
| ASTM C 685/C685M : 2024 | Standard Specification for Concrete Made by Volumetric Batching and Continuous Mixing |
| ASTM E 11 : 2022 | Standard Specification for Woven Wire Test Sieve Cloth and Test Sieves |
| ASTM C 685/C685M : 2025 | Standard Specification for Concrete Made by Volumetric Batching and Continuous Mixing |
Access your standards online with a subscription
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.