• Shopping Cart
    There are no items in your cart

ASTM C 1725 : 2017

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by

Standard Guide for Hot Cell Specialized Support Equipment and Tools

Available format(s)

Hardcopy , PDF

Superseded date

23-08-2022

Language(s)

English

Published date

19-06-2017

€74.48
Excluding VAT

Committee
C 26
DocumentType
Guide
Pages
15
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

1.1Intent:

1.1.1This guide presents practices and guidelines for the design and implementation of equipment and tools to assist assembly, disassembly, alignment, fastening, maintenance, or general handling of equipment in a hot cell. Operating in a remote hot cell environment significantly increases the difficulty and time required to perform a task compared to completing a similar task directly by hand. Successful specialized support equipment and tools minimize the required effort, reduce risks, and increase operating efficiencies.

1.2Applicability:

1.2.1This guide may apply to the design of specialized support equipment and tools anywhere it is remotely operated, maintained, and viewed through shielding windows or by other remote viewing systems.

1.2.2Consideration should be given to the need for specialized support equipment and tools early in the design process.

1.2.3The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.3Caveats:

1.3.1This guide is generic in nature and addresses a wide range of remote working configurations. Other acceptable and proven international configurations exist and provide options for engineer and designer consideration. Specific designs are not a substitute for applied engineering skills, proven practices, or experience gained in any specific situation.

1.3.2This guide does not supersede federal or state regulations, or both, or codes applicable to equipment under any conditions.

1.3.3This guide does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ASTM C 1533 : 2015 Standard Guide for General Design Considerations for Hot Cell Equipment

ASTM A 962/A962M : 2019 Standard Specification for Common Requirements for Bolting Intended for Use at Any Temperature from Cryogenic to the Creep Range
ASTM C 859 : 2014 : REV B Standard Terminology Relating to Nuclear Materials
ASTM C 1615 : 2005 Standard Guide for Mechanical Drive Systems for Remote Operation in Hot Cell Facilities
ASTM C 1554 : 2011 Standard Guide for Materials Handling Equipment for Hot Cells
ASTM C 1533 : 2015 Standard Guide for General Design Considerations for Hot Cell Equipment
ASTM A 193/A193M : 2004 : REV B Standard Specification for Alloy-Steel and Stainless Steel Bolting Materials for High-Temperature Service
ASTM A 962/A962M : 2022 Standard Specification for Common Requirements for Bolting Intended for Use at Any Temperature from Cryogenic to the Creep Range
ASTM C 1554 : 2018 Standard Guide for Materials Handling Equipment for Hot Cells
ASTM C 1217 : 2000 : R2006 Standard Guide for Design of Equipment for Processing Nuclear and Radioactive Materials
ASTM C 1615 : 2010 Standard Guide for Mechanical Drive Systems for Remote Operation in Hot Cell Facilities
ASTM C 859 : 2022 Standard Terminology Relating to Nuclear Materials
ASTM C 1217 : 2000 : R2012 Standard Guide for Design of Equipment for Processing Nuclear and Radioactive Materials
ASTM C 859 : 2022 : REV A Standard Terminology Relating to Nuclear Materials
ASTM C 1554 : 2003 Standard Guide for Materials Handling Equipment for Hot Cells
ASTM C 1661 : 2013 Standard Guide for Viewing Systems for Remotely Operated Facilities
ASTM C 1217 : 2000 Standard Guide for Design of Equipment for Processing Nuclear and Radioactive Materials
ASTM C 1533 : 2008 Standard Guide for General Design Considerations for Hot Cell Equipment
ASTM C 1661 : 2018 Standard Guide for Viewing Systems for Remotely Operated Facilities
ASTM C 1661 : 2007 Standard Guide for Viewing Systems for Remotely Operated Facilities
ASTM C 1533 : 2002 Standard Guide for General Design Considerations for Hot Cell Equipment

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.