ASTM C 1797 : 2023 : REV A
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Ground Calcium Carbonate and Aggregate Mineral Fillers for use in Hydraulic Cement Concrete
Hardcopy , PDF
12-12-2024
English
01-12-2023
Committee |
C 09
|
DocumentType |
Standard
|
Pages |
7
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
1.1This specification applies to ground calcium carbonate (GCC is a type of ground limestone) and other finely divided aggregate mineral filler (AMF) materials for use in concrete mixtures. The specification defines the types of GCC and AMF materials for use in concrete.
1.2If concrete in service is subject to sulfate exposure, fillers derived from ground limestone should not be used unless mitigation methods are used.
Note 1:American Concrete Institute (ACI) technical documents 201.2R, 318, 332, and 350 contain useful information and code requirements dealing with sulfate exposure in service. Soluble sulfate in water can be determined in accordance with Test Method D516 or Test Method D4130. Percent sulfate by mass in soil can be determined by Test Method C1580.
1.3The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
Note 2:Sieve size is identified by its standard designation in Specification E11. The alternative designation given in parentheses is for information only and does not represent a different standard sieve size.
1.4The text of this standard references notes and footnotes, which provide explanatory information. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.
1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM C 94/C94M : 2023 | Standard Specification for Ready-Mixed Concrete |
ASTM E 3355 : 2023 | Standard Guide for Characterization of Coal Combustion Products (CCPs) in Storage Area(s) for Beneficial Use |
ASTM C 94/C94M : 2024 : REV C | Standard Specification for Ready-Mixed Concrete |
ASTM D 1193 : 2024 | Standard Specification for Reagent Water |
ASTM C 117 : 2017 | Standard Test Method for Materials Finer than 75-μm (No. 200) Sieve in Mineral Aggregates by Washing |
ASTM E 832 : 1981 : R2019 | Standard Specification for Laboratory Filter Papers |
ASTM C 25 : 2024 | Standard Test Methods for Chemical Analysis of Limestone, Quicklime, and Hydrated Lime |
ASTM E 832 : 1981 : R2024 | Standard Specification for Laboratory Filter Papers |
ASTM C 110 : 2020 | Standard Test Methods for Physical Testing of Quicklime, Hydrated Lime, and Limestone |
ASTM E 11 : 2024 | Standard Specification for Woven Wire Test Sieve Cloth and Test Sieves |
ASTM C 125 : 2024 | Standard Terminology Relating to Concrete and Concrete Aggregates |
ASTM E 1019 : 2018 | Standard Test Methods for Determination of Carbon, Sulfur, Nitrogen, and Oxygen in Steel, Iron, Nickel, and Cobalt Alloys by Various Combustion and Inert Gas Fusion Techniques |
ASTM C 311/C311M : 2022 | Standard Test Methods for Sampling and Testing Fly Ash or Natural Pozzolans for Use in Portland-Cement Concrete |
ASTM E 11 : 2022 | Standard Specification for Woven Wire Test Sieve Cloth and Test Sieves |
ASTM C 311/C311M : 2024 | Standard Test Methods for Sampling and Testing Coal Ash or Natural Pozzolans for Use in Concrete |
ASTM E 1019 : 2024 | Standard Test Methods for Determination of Carbon, Sulfur, Nitrogen, and Oxygen in Steel, Iron, Nickel, and Cobalt Alloys by Combustion and Inert Gas Fusion Techniques |
ASTM C 117 : 2023 | Standard Test Method for Materials Finer than 75-μm (No. 200) Sieve in Mineral Aggregates by Washing |
ASTM C 110 : 2024 | Standard Test Methods for Physical Testing of Quicklime, Hydrated Lime, and Limestone |
ASTM D 4130 : 2015 | Standard Test Method for Sulfate Ion in Brackish Water, Seawater, and Brines (Withdrawn 2024) |
ASTM C 25 : 2019 : EDT 1 | Standard Test Methods for Chemical Analysis of Limestone, Quicklime, and Hydrated Lime |
ASTM E 350 : 2023 | Standard Test Methods for Chemical Analysis of Carbon Steel, Low-Alloy Steel, Silicon Electrical Steel, Ingot Iron, and Wrought Iron |
ASTM C 125 : 2021 : REV A | Standard Terminology Relating to Concrete and Concrete Aggregates |
ASTM D 1193 : 2006 : R2018 | Standard Specification for Reagent Water |
ASTM C 25 : 2019 | Standard Test Methods for Chemical Analysis of Limestone, Quicklime, and Hydrated Lime |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.