ASTM C 449 : 2007 : R2019
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Mineral Fiber Hydraulic-Setting Thermal Insulating and Finishing Cement
Hardcopy , PDF
20-09-2024
English
01-03-2019
CONTAINED IN VOL. 04.06, 2014 Defines mineral fiber (rock or slag) insulating and finishing cement shipped in dry-mix form, including hydraulic-setting binder, which, when mixed with water and applied in accordance with the manufacturer's directions, affords a smooth surface as a final finish for heated surfaces up to 1200 degrees F (649 degrees C) for specific applications.
Committee |
C 16
|
DevelopmentNote |
Supersedes ASTM C 449/C449M. (12/2007) Supersedes MIL C 2908 (B). (09/2010)
|
DocumentType |
Standard
|
Pages |
3
|
ProductNote |
Reconfirmed 2007
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
1.1This specification covers mineral fiber (rock or slag) insulating and finishing cement shipped in dry-mix form, including hydraulic-setting binder, which, when mixed with water and applied in accordance with the manufacturer's directions, affords a smooth surface as a final finish for heated surfaces up to 1200 °F (649 °C) for specific applications. The actual temperature limit shall be agreed upon between the purchaser and the manufacturer.
Note 1:Precautionary measures should be taken with this material as with other hydraulic-setting mixtures. This material should be used within the time period recommended by the manufacturer.
1.2The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3The following safety hazards caveat pertains only to the test method (Section 10) described in this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.4When the installation or use of thermal insulation materials, accessories, and systems pose safety or health problems, the manufacturer shall provide the user with appropriate current information regarding any known problems associated with the recommended use of the company's products and shall also recommend protective measures to be employed in their safe utilization. The user shall establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.
1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM C 1696 : 2020 | Standard Guide for Industrial Thermal Insulation Systems |
ASTM C 929 : 2014(R2019) | Standard Practice for Handling, Transporting, Shipping, Storage, Receiving, and Application of Thermal Insulation Materials For Use in Contact with Austenitic Stainless Steel |
ASTM E 136 : 2024 | Standard Test Method for Assessing Combustibility of Materials Using a Vertical Tube Furnace at 750 °C |
ASTM C 168 : 2019 | Standard Terminology Relating to Thermal Insulation |
ASTM C 1045 : 2019 | Standard Practice for Calculating Thermal Transmission Properties Under Steady-State Conditions |
ASTM C 177 : 2019 | Standard Test Method for Steady-State Heat Flux Measurements and Thermal Transmission Properties by Means of the Guarded-Hot-Plate Apparatus |
ASTM C 1114 : 2006 : R2013 | Standard Test Method for Steady-State Thermal Transmission Properties by Means of the Thin-Heater Apparatus |
ASTM C 1114 : 2006 : R2019 | Standard Test Method for Steady-State Thermal Transmission Properties by Means of the Thin-Heater Apparatus |
ASTM C 1045 : 2007 : R2013 | Standard Practice for Calculating Thermal Transmission Properties Under Steady-State Conditions |
ASTM C 518 : 2017 : REDLINE | Standard Test Method for Steady-State Thermal Transmission Properties by Means of the Heat Flow Meter Apparatus |
ASTM C 163 : 2005 : R2023 | Standard Practice for Mixing Thermal Insulating Cement Samples |
ASTM C 356 : 2022 | Standard Test Method for Linear Shrinkage of Preformed High-Temperature Thermal Insulation Subjected to Soaking Heat |
ASTM E 136 : 2024 : REV B | Standard Test Method for Assessing Combustibility of Materials Using a Vertical Tube Furnace at 750 °C |
ASTM C 163 : 2005 : R2016 | Standard Practice for Mixing Thermal Insulating Cement Samples |
ASTM C 1058 : 1997 | Standard Practice for Selecting Temperatures for Evaluating and Reporting Thermal Properties of Thermal Insulation |
ASTM E 136 : 2022 | Standard Test Method for Assessing Combustibility of Materials Using a Vertical Tube Furnace at 750 °C |
ASTM C 1058 : 2003 | Standard Practice for Selecting Temperatures for Evaluating and Reporting Thermal Properties of Thermal Insulation |
ASTM C 390 : 2008 : R2024 | Standard Practice for Sampling and Acceptance of Thermal Insulation Lots |
ASTM C 1114 : 2006 | Standard Test Method for Steady-State Thermal Transmission Properties by Means of the Thin-Heater Apparatus |
ASTM E 136 : 2019 : REV A | Standard Test Method for Assessing Combustibility of Materials Using a Vertical Tube Furnace at 750°C |
ASTM C 1045 : 2001 | Standard Practice for Calculating Thermal Transmission Properties Under Steady-State Conditions |
ASTM C 518 : 2002 | Standard Test Method for Steady-State Thermal Transmission Properties by Means of the Heat Flow Meter Apparatus |
ASTM C 390 : 2008 : R2019 | Standard Practice for Sampling and Acceptance of Thermal Insulation Lots |
ASTM C 356 : 2017 | Standard Test Method for Linear Shrinkage of Preformed High-Temperature Thermal Insulation Subjected to Soaking Heat |
ASTM C 168 : 2024 | Standard Terminology Relating to Thermal Insulation |
ASTM C 356 : 2017 : REDLINE | Standard Test Method for Linear Shrinkage of Preformed High-Temperature Thermal Insulation Subjected to Soaking Heat |
ASTM C 1114 : 2000 | Standard Test Method for Steady-State Thermal Transmission Properties by Means of the Thin-Heater Apparatus |
ASTM E 136 : 2016-02 | TEST METHOD FOR BEHAVIOUR OF MATERIALS IN A VERTICAL TUBE FURNACE AT 750 DEGREES C |
ASTM C 518 : 2017 | Standard Test Method for Steady-State Thermal Transmission Properties by Means of the Heat Flow Meter Apparatus |
ASTM C 166 : 2005 : R2023 | Standard Test Method for Covering Capacity and Volume Change Upon Drying of Thermal Insulating Cement |
ASTM C 518 : 2021 | Standard Test Method for Steady-State Thermal Transmission Properties by Means of the Heat Flow Meter Apparatus |
ASTM C 1114 : 2000 : R2006 | Standard Test Method for Steady-State Thermal Transmission Properties by Means of the Thin-Heater Apparatus |
ASTM C 1045 : 1997 | Standard Practice for Calculating Thermal Transmission Properties Under Steady-State Conditions |
ASTM C 795 : 2008 : R2023 | Standard Specification for Thermal Insulation for Use in Contact with Austenitic Stainless Steel |
ASTM C 166 : 2005 : R2016 | Standard Test Method for Covering Capacity and Volume Change Upon Drying of Thermal Insulating Cement |
ASTM C 177 : 2019 : EDT 1 | Standard Test Method for Steady-State Heat Flux Measurements and Thermal Transmission Properties by Means of the Guarded-Hot-Plate Apparatus |
ASTM E 136 : 2024 : REV C | Standard Test Method for Assessing Combustibility of Materials Using a Vertical Tube Furnace at 750 °C |
ASTM C 168 : 2022 | Standard Terminology Relating to Thermal Insulation |
ASTM C 1058 : 2003 : R2008 | Standard Practice for Selecting Temperatures for Evaluating and Reporting Thermal Properties of Thermal Insulation |
ASTM C 795 : 2008 : R2018 | Standard Specification for Thermal Insulation for Use in Contact with Austenitic Stainless Steel |
ASTM C 795 : 2008 | Standard Specification for Thermal Insulation for Use in Contact with Austenitic Stainless Steel |
ASTM E 136 : 2024 : REV A | Standard Test Method for Assessing Combustibility of Materials Using a Vertical Tube Furnace at 750 °C |
ASTM C 1045 : 2007 | Standard Practice for Calculating Thermal Transmission Properties Under Steady-State Conditions |
ASTM C 795 : 1992 : R1998 : EDT 1 | Standard Specification for Thermal Insulation for Use in Contact with Austenitic Stainless Steel |
ASTM C 168 : 2017-06 | TERMINOLOGY RELATING TO THERMAL INSULATION |
ASTM C 518 : 1998 | Standard Test Method for Steady-State Thermal Transmission Properties by Means of the Heat Flow Meter Apparatus |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.