ASTM C 470/C470M : 2015 : REDLINE
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Molds for Forming Concrete Test Cylinders Vertically
12-07-2023
English
02-04-2015
Important note : Users cannot be edited or removed once added to your Multi user PDF.CONTAINED IN VOL. 04.02, 2015 Defines molds for use in forming cylindrical concrete specimens.
| Committee |
C 09
|
| DevelopmentNote |
Supersedes ASTM C 470. (08/2008)
|
| DocumentType |
Redline
|
| Pages |
5
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy |
1.1This specification covers molds for use in forming cylindrical concrete specimens. The provisions of this specification include the requirements for both reusable and single-use molds.
Note 1:Sizes included are molds having diameters from 50 mm [2 in.] to 900 mm [36 in.].
1.2The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.
1.3The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. The inch-pound units are shown in brackets.
1.4The following safety hazards caveat pertains only to the test method described in this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| ASTM C 1435/C1435M : 2014 : REDLINE | Standard Practice for Molding Roller-Compacted Concrete in Cylinder Molds Using a Vibrating Hammer |
| ASTM C 567 : 2005 : REV A | Standard Test Method for Determining Density of Structural Lightweight Concrete |
| ASTM C 267:2001 | Standard Test Methods for Chemical Resistance of Mortars, Grouts, and Monolithic Surfacings and Polymer Concretes |
| ASTM C 579 : 2001 : R2012 | Standard Test Methods for Compressive Strength of Chemical-Resistant Mortars, Grouts, Monolithic Surfacings, and Polymer Concretes |
| ASTM C 1093 : 2015-06 | PRACTICE FOR ACCREDITATION OF TESTING AGENCIES FOR MASONRY |
| ASTM C 267 : 2001 : R2006 | Standard Test Methods for Chemical Resistance of Mortars, Grouts, and Monolithic Surfacings and Polymer Concretes |
| ASTM C 512/C512M : 2015 : REDLINE | Standard Test Method for Creep of Concrete in Compression |
| ASTM C 31/C31M : 2018-02 | PRACTICE FOR MAKING AND CURING CONCRETE TEST SPECIMENS IN THE FIELD |
| ASTM C 413 : 2001 | Standard Test Method for Absorption of Chemical-Resistant Mortars, Grouts, and Monolithic Surfacings and Polymer Concretes |
| ASTM C 413 : 2001 : R2012 | Standard Test Method for Absorption of Chemical-Resistant Mortars, Grouts, Monolithic Surfacings, and Polymer Concretes |
| ASTM C 918/C918M : 2013 : REDLINE | Standard Test Method for Measuring Early-Age Compressive Strength and Projecting Later-Age Strength |
| ASTM C 192/C192M : 2016-04 | PRACTICE FOR MAKING AND CURING CONCRETE TEST SPECIMENS IN THE LABORATORY |
| ASTM C 1312 : 1997 : R2008 | Standard Practice for Making and Conditioning Chemical-Resistant Sulfur Polymer Cement Concrete Test Specimens in the Laboratory |
| ASTM C 267 : 2001 : R2012 | Standard Test Methods for Chemical Resistance of Mortars, Grouts, and Monolithic Surfacings and Polymer Concretes |
| ASTM C 1312 : 1997 : R2003 | Standard Practice for Making and Conditioning Chemical-Resistant Sulfur Polymer Cement Concrete Test Specimens in the Laboratory |
| ASTM C 1747/C1747M : 2013 : REDLINE | Standard Test Method for Determining Potential Resistance to Degradation of Pervious Concrete by Impact and Abrasion |
| ASTM C 905 : 2001 : R2006 | Standard Test Methods for Apparent Density of Chemical-Resistant Mortars, Grouts, Monolithic Surfacings, and Polymer Concretes |
| ASTM C 873/C873M : 2015 : REDLINE | Standard Test Method for Compressive Strength of Concrete Cylinders Cast in Place in Cylindrical Molds |
| ASTM C 1312 : 1997 : R2012 | Standard Practice for Making and Conditioning Chemical-Resistant Sulfur Polymer Cement Concrete Test Specimens in the Laboratory (Withdrawn 2021) |
| ACI PRC-363.2 : 2011 | GUIDE TO QUALITY CONTROL AND ASSURANCE OF HIGH-STRENGTH CONCRETE |
| ACI 533R : 2011 | GUIDE FOR PRECAST CONCRETE WALL PANELS |
| ASTM C 882/C882M : 2013-08 | TEST METHOD FOR BOND STRENGTH OF EPOXY-RESIN SYSTEMS USED WITH CONCRETE BY SLANT SHEAR |
| ASTM C 873 : 2004 | Standard Test Method for Compressive Strength of Concrete Cylinders Cast in Place in Cylindrical Molds |
| ASTM C 1176/C1176M : 2013 : REDLINE | Standard Practice for Making Roller-Compacted Concrete in Cylinder Molds Using a Vibrating Table |
| ACI 305R : 2010 | GUIDE TO HOT WEATHER CONCRETING |
| ASTM C 905 : 2001 : R2012 | Standard Test Methods for Apparent Density of Chemical-Resistant Mortars, Grouts, Monolithic Surfacings, and Polymer Concretes (Withdrawn 2021) |
| ASTM C 1312 : 1997 | Standard Practice for Making and Conditioning Chemical-Resistant Sulfur Polymer Cement Concrete Test Specimens in the Laboratory |
| ASTM C 1768/C1768M : 2012 | Standard Practice for Accelerated Curing of Concrete Cylinders |
| ASTM C 567/C567M : 2014 : REDLINE | Standard Test Method for Determining Density of Structural Lightweight Concrete |
| ASTM C 905 : 2001 | Standard Test Methods for Apparent Density of Chemical-Resistant Mortars, Grouts, Monolithic Surfacings, and Polymer Concretes |
| ASTM C 413 : 2001 : R2006 | Standard Test Method for Absorption of Chemical-Resistant Mortars, Grouts, Monolithic Surfacings, and Polymer Concretes |
| ASTM C 567 : 2005 | Standard Test Method for Determining Density of Structural Lightweight Concrete |
| ASTM C 579 : 2001 | Standard Test Methods for Compressive Strength of Chemical-Resistant Mortars, Grouts, Monolithic Surfacings and Polymer Concretes |
| ASTM C 579 : 2001 : R2006 | Standard Test Methods for Compressive Strength of Chemical-Resistant Mortars, Grouts, Monolithic Surfacings, and Polymer Concretes |
| ASTM C 1176 : 2005 | Standard Practice for Making Roller-Compacted Concrete in Cylinder Molds Using a Vibrating Table |
| ASTM C 1768/C1768M : 2012 : R2017 | Standard Practice for Accelerated Curing of Concrete Cylinders |
| ASTM C 1077 : 2017 : REDLINE | Standard Practice for Agencies Testing Concrete and Concrete Aggregates for Use in Construction and Criteria for Testing Agency Evaluation |
| ASTM C 192/C192M : 2016-04 | PRACTICE FOR MAKING AND CURING CONCRETE TEST SPECIMENS IN THE LABORATORY |
| ASTM D 570 : 1998 : R2018 | Standard Test Method for Water Absorption of Plastics |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.