![header thumbnail](/images/publishers\astm_cover.gif)
ASTM C 511 : 2019
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
![header thumbnail](/images/publishers\astm_cover.gif)
Standard Specification for Mixing Rooms, Moist Cabinets, Moist Rooms, and Water Storage Tanks Used in the Testing of Hydraulic Cements and Concretes
Hardcopy , PDF
05-01-2022
English
01-07-2019
This specification includes requirements for mixing rooms where paste and mortar specimens are prepared; and for moist cabinets, moist rooms, and water storage tanks where paste, mortar, and concrete specimens are stored.
Committee |
C 01
|
DocumentType |
Standard
|
Pages |
3
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
1.1This specification includes requirements for mixing rooms where paste and mortar specimens are prepared; and for moist cabinets, moist rooms, and water storage tanks where paste, mortar, and concrete specimens are stored.
1.2The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. Values in SI units shall be obtained by measurement in SI units or by appropriate conversion, using the Rules for Conversion and rounding given in Standard IEEE/ASTM SI 10, of measurements made in other units.
1.3The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of this standard.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM C 1329/C1329M : 2016 : REV A | Standard Specification for Mortar Cement |
ASTM C 796/C796M : 2019 | Standard Test Method for Foaming Agents for Use in Producing Cellular Concrete Using Preformed Foam |
ASTM C 1608 : 2017 | Standard Test Method for Chemical Shrinkage of Hydraulic Cement Paste |
ASTM C 87/C87M : 2017 | Standard Test Method for Effect of Organic Impurities in Fine Aggregate on Strength of Mortar |
ASTM C 109/C109M : 2021 | Standard Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 2-in. or [50mm] Cube Specimens) |
ASTM D 1734 : 1993 : R2013 | Standard Practice for Making Cementitious Panels for Testing Coatings |
ASTM C 1506 : 2017 | Standard Test Method for Water Retention of Hydraulic Cement-Based Mortars and Plasters |
ASTM C 1792 : 2014 | Standard Test Method for Measurement of Mass Loss versus Time for One-Dimensional Drying of Saturated Concretes (Withdrawn 2023) |
ASTM C 91/C91M : 2018 | Standard Specification for Masonry Cement |
ASTM C 151/C151M : 2018 | Standard Test Method for Autoclave Expansion of Hydraulic Cement |
ASTM C 266 : 2021 | Standard Test Method for Time of Setting of Hydraulic-Cement Paste by Gillmore Needles |
ASTM C 192/C192M : 2019 | Standard Practice for Making and Curing Concrete Test Specimens in the Laboratory |
ASTM C 452 : 2021 | Standard Test Method for Potential Expansion of Portland-Cement Mortars Exposed to Sulfate |
ASTM C 305 : 2020 | Standard Practice for Mechanical Mixing of Hydraulic Cement Pastes and Mortars of Plastic Consistency |
ASTM C 596 : 2018 | Standard Test Method for Drying Shrinkage of Mortar Containing Hydraulic Cement |
ASTM A 1096/A1096M : 2015 | Standard Test Method for Evaluating Bond of Individual Steel Wire, Indented or Plain, for Concrete Reinforcement |
ASTM C 157/C157M : 2017 | Standard Test Method for Length Change of Hardened Hydraulic-Cement Mortar and Concrete |
ASTM C 953 : 2017 | Standard Test Method for Time of Setting of Grouts for Preplaced-Aggregate Concrete in the Laboratory |
ASTM C 1105 : 2008 : REV A : R2016 | Standard Test Method for Length Change of Concrete Due to Alkali-Carbonate Rock Reaction |
ASTM C 1019 : 2020 | Standard Test Method for Sampling and Testing Grout for Masonry |
ASTM D 8337/D8337M : 2021 | Standard Test Method for Evaluation of Bond Properties of FRP Composite Applied to Concrete Substrate using Single-Lap Shear Test |
ASTM C 1038/C1038M : 2019 | Standard Test Method for Expansion of Hydraulic Cement Mortar Bars Stored in Water |
ASTM C 187 : 2016 | Standard Test Method for Amount of Water Required for Normal Consistency of Hydraulic Cement Paste |
ASTM C 185 : 2020 | Standard Test Method for Air Content of Hydraulic Cement Mortar |
ASTM C 1403 : 2015 | Standard Test Method for Rate of Water Absorption of Masonry Mortars |
ASTM C 1567 : 2021 | Standard Test Method for Determining the Potential Alkali-Silica Reactivity of Combinations of Cementitious Materials and Aggregate (Accelerated Mortar-Bar Method) |
ASTM C 1260 : 2021 | Standard Test Method for Potential Alkali Reactivity of Aggregates (Mortar-Bar Method) |
ASTM C 1757 : 2013 | Standard Test Method for Determination of One-Point, Bulk Water Sorption of Dried Concrete (Withdrawn 2022) |
ASTM C 887 : 2020 | Standard Specification for Packaged, Dry, Combined Materials for Surface Bonding Mortar |
ASTM D 7958/D7958M : 2017 | Standard Test Method for Evaluation of Performance for FRP Composite Bonded to Concrete Substrate using Beam Test |
ASTM G 109 : 2007 : R2013 | Standard Test Method for Determining Effects of Chemical Admixtures on Corrosion of Embedded Steel Reinforcement in Concrete Exposed to Chloride Environments |
ASTM C 1713 : 2017 | Standard Specification for Mortars for the Repair of Historic Masonry |
ASTM C 780 : 2020 | Standard Test Method for Preconstruction and Construction Evaluation of Mortars for Plain and Reinforced Unit Masonry |
ASTM C 1670/C1670M : 2021 : REV A | Standard Specification for Adhered Manufactured Stone Masonry Veneer Units |
ASTM C 932 : 2006 : R2019 | Standard Specification for Surface-Applied Bonding Compounds for Exterior Plastering |
ASTM C 1749 : 2017 : REV A | Standard Guide for Measurement of the Rheological Properties of Hydraulic Cementious Paste Using a Rotational Rheometer |
ASTM C 1140/C1140M : 2011 : R2019 | Standard Practice for Preparing and Testing Specimens from Shotcrete Test Panels |
ASTM C 1707 : 2018 | Standard Specification for Pozzolanic Hydraulic Lime for Structural Purposes |
ASTM D 7705/D7705M : 2012 : R2019 | Standard Test Method for Alkali Resistance of Fiber Reinforced Polymer (FRP) Matrix Composite Bars used in Concrete Construction |
ASTM C 441/C441M : 2017 | Standard Test Method for Effectiveness of Pozzolans or Ground Blast-Furnace Slag in Preventing Excessive Expansion of Concrete Due to the Alkali-Silica Reaction |
ASTM C 1708/C1708M : 2019 | Standard Test Methods for Self-leveling Mortars Containing Hydraulic Cements |
ASTM C 1437 : 2020 | Standard Test Method for Flow of Hydraulic Cement Mortar |
ASTM C 1222 : 2021 | Standard Practice for Evaluation of Laboratories Testing Hydraulic Cement |
ASTM C 31/C31M : 2021 : REV A | Standard Practice for Making and Curing Concrete Test Specimens in the Field |
ASTM A 981/A981M : 2011 : R2016 | Standard Test Method for Evaluating Bond Strength for 0.600-in. [15.24-mm] Diameter Steel Prestressing Strand, Grade 270 [1860], Uncoated, Used in Prestressed Ground Anchors |
ASTM C 882/C882M : 2020 | Standard Test Method for Bond Strength of Epoxy-Resin Systems Used With Concrete By Slant Shear |
ASTM C 1679 : 2017 | Standard Practice for Measuring Hydration Kinetics of Hydraulic Cementitious Mixtures Using Isothermal Calorimetry |
ASTM C 1012/C1012M : 2018 : REV B | Standard Test Method for Length Change of Hydraulic-Cement Mortars Exposed to a Sulfate Solution |
ASTM C 1738/C1738M : 2019 | Standard Practice for High-Shear Mixing of Hydraulic Cement Pastes |
ASTM C 191 : 2021 | Standard Test Methods for Time of Setting of Hydraulic Cement by Vicat Needle |
ASTM C 125 : 2021 : REV A | Standard Terminology Relating to Concrete and Concrete Aggregates |
ASTM C 1074 : 2019 : EDT 1 | Standard Practice for Estimating Concrete Strength by the Maturity Method |
ASTM C 1090/C1090M : 2015 | Standard Test Method for Measuring Changes in Height of Cylindrical Specimens of Hydraulic-Cement Grout |
ASTM C 1328/C1328M : 2019 : REDLINE | Standard Specification for Plastic (Stucco) Cement |
ASTM D 7913/D7913M : 2014 : R2020 | Standard Test Method for Bond Strength of Fiber-Reinforced Polymer Matrix Composite Bars to Concrete by Pullout Testing |
ASTM C 631 : 2009 : R2020 | Standard Specification for Bonding Compounds for Interior Gypsum Plastering |
ASTM C 125 : 2021 | Standard Terminology Relating to Concrete and Concrete Aggregates |
ASTM C 125 : 2000 | Standard Terminology Relating to Concrete and Concrete Aggregates |
ASTM E 77 : 2014 : EDT 1 | Standard Test Method for Inspection and Verification of Thermometers |
ASTM C 125 : 2021 : REV A | Standard Terminology Relating to Concrete and Concrete Aggregates |
ASTM C 51 : 2001 | Standard Terminology Relating to Lime and Limestone (as used by the Industry) |
ASTM C 51 : 2021 | Standard Terminology Relating to Lime and Limestone (as Used by the Industry) |
ASTM C 51 : 2020 | Standard Terminology Relating to Lime and Limestone (as Used by the Industry) |
ASTM E 77 : 1998 | Standard Test Method for Inspection and Verification of Thermometers |
ASTM E 77 : 2014 : R2021 | Standard Test Method for Inspection and Verification of Thermometers |
ASTM C 125 : 2009 | Standard Terminology Relating to Concrete and Concrete Aggregates |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.