ASTM C 639 : 2015 : REDLINE
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Rheological (Flow) Properties of Elastomeric Sealants
27-11-2024
English
01-06-2015
Important note : Users cannot be edited or removed once added to your Multi user PDF.CONTAINED IN VOL. 04.07, 2015 Specifies a laboratory procedure for the determination of rheological (flow) properties of single and multicomponent chemically curing sealants for use in building construction.
| Committee |
C 24
|
| DocumentType |
Redline
|
| Pages |
3
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy |
1.1This test method describes a laboratory procedure for the determination of rheological (flow) properties of single- and multicomponent chemically curing sealants for use in building construction.
1.2Other suitable flow characteristics may be agreed upon between the seller and purchaser or specifier. Special nonsag properties and lower flow characteristics may be required for use in sloping joints where absolute leveling is not desired.
Note 1:The sealants are supplied in various rheological properties ranging from pourable fluids to stiff nonsagging pastes. Multicomponent sealants are supplied as a base component with an activator or curing agent separately packaged. After mixing the multiple parts, the sealant is ready for application. Single-component sealants are supplied ready for use upon opening of the package and usually depend on the external environment for cure.
1.3This test method describes four types of joint sealants:
1.3.1Type I—Single-component flowable or self-leveling,
1.3.2Type II—Single-component nonsag,
1.3.3Type III—Multicomponent flowable or self-leveling, and
1.3.4Type IV—Multicomponent nonsag.
1.4The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.5This standard does not purport to address the safety problems associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| ASTM C 1299 : 2003 | Standard Guide for Use in Selection of Liquid-Applied Sealants (Withdrawn 2012) |
| ASTM C 647 : 2008 | Standard Guide to Properties and Tests of Mastics and Coating Finishes for Thermal Insulation |
| ASTM C 1021 : 2008 | Standard Practice for Laboratories Engaged in Testing of Building Sealants |
| ASTM C 1369 : 2007 : R2014 | Standard Specification for Secondary Edge Sealants for Structurally Glazed Insulating Glass Units |
| ASTM D 5893/D5893M : 2016 : REDLINE | Standard Specification for Cold Applied, Single Component, Chemically Curing Silicone Joint Sealant for Portland Cement Concrete Pavements |
| ASTM C 1021 : 2008 : R2014 | Standard Practice for Laboratories Engaged in Testing of Building Sealants |
| ASTM D 8138 : 2018 | Standard Specification for Preformed Silicone Joint Sealing System for Bridges |
| ASTM C 1369 : 2007 | Standard Specification for Secondary Edge Sealants for Structurally Glazed Insulating Glass Units |
| ASTM C 647 : 2008 : R2013 | Standard Guide to Properties and Tests of Mastics and Coating Finishes for Thermal Insulation |
| ASTM C 920 : 2018 : REDLINE | Standard Specification for Elastomeric Joint Sealants |
| ASTM D 5893 : 2004 | Standard Specification for Cold Applied, Single Component, Chemically Curing Silicone Joint Sealant for Portland Cement Concrete Pavements |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.