ASTM C 719 : 2014 : R2019
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Adhesion and Cohesion of Elastomeric Joint Sealants Under Cyclic Movement (Hockman Cycle)
Hardcopy , PDF
24-03-2022
English
15-01-2019
Important note : Users cannot be edited or removed once added to your Multi user PDF.| Committee |
C 24
|
| DocumentType |
Test Method
|
| Pages |
6
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This test method is an accelerated laboratory procedure for evaluating the performance of a building sealant in a test configuration that is subjected to water immersion, cyclic movement, and temperature change.3
1.2The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM C 1589/C1589M : 2018 | Standard Practice for Outdoor Weathering of Construction Seals and Sealants |
| ASTM E 1399/E1399M : 1997 : R2017 | Standard Test Method for Cyclic Movement and Measuring the Minimum and Maximum Joint Widths of Architectural Joint Systems |
| ASTM E 1996 : 2020 | Standard Specification for Performance of Exterior Windows, Curtain Walls, Doors, and Impact Protective Systems Impacted by Windborne Debris in Hurricanes |
| ASTM C 1564 : 2020 | Standard Guide for Use of Silicone Sealants for Protective Glazing Systems |
| ASTM C 1401 : 2014 | Standard Guide for Structural Sealant Glazing |
| ASTM C 1481 : 2012 : R2017 | Standard Guide for Use of Joint Sealants with Exterior Insulation and Finish Systems (EIFS) |
| ASTM C 712 : 2022 | Standard Test Method for Bubbling of One-Part, Elastomeric, Solvent-Release Type Sealants |
| ASTM C 1681 : 2018 | Standard Test Method for Evaluating the Tear Resistance of a Sealant Under Constant Strain |
| ASTM C 920 : 2018 | Standard Specification for Elastomeric Joint Sealants |
| ASTM C 1815 : 2017 : R2021 | Standard Practice for Periodically Measuring and Monitoring Sealant Dimensions to Stability Following a Period of Compression or Tension |
| ASTM D 3667 : 2016 | Standard Specification for Rubber Seals Used in Flat-Plate Solar Collectors |
| ASTM D 3903 : 2015 | Standard Specification for Rubber Seals Used in Air-Heat Transport of Solar Energy Systems |
| ASTM C 1519 : 2010 : R2017 | Standard Test Method for Evaluating Durability of Building Construction Sealants by Laboratory Accelerated Weathering Procedures |
| ASTM C 1472 : 2016 : EDT 1 | Standard Guide for Calculating Movement and Other Effects When Establishing Sealant Joint Width |
| ASTM C 1247 : 2020 | Standard Test Method for Durability of Sealants Exposed to Continuous Immersion in Liquids |
| ASTM C 1193 : 2016 | Standard Guide for Use of Joint Sealants |
| ASTM D 3771 : 2015 | Standard Specification for Rubber Seals Used in Concentrating Solar Collectors |
| ASTM C 1635 : 2016 | Standard Test Method to Evaluate Adhesion/Cohesion Properties of a Sealant at Fixed Extension |
| ASTM C 1021 : 2008 : R2019 | Standard Practice for Laboratories Engaged in Testing of Building Sealants |
| ASTM C 1735 : 2017 : R2021 | Standard Test Method for Measuring the Time Dependent Modulus of Sealants Using Stress Relaxation |
| ASTM C 1851 : 2018 | Standard Practice for Determining the Extent of Cracking in a Sealant using the Difference between the Compressive and Tensile Modulus |
| ASTM C 109/C109M : 2020 : REV B | Standard Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 2-in. or [50mm] Cube Specimens) |
| ASTM C 109/C109M : 2021 | Standard Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 2-in. or [50mm] Cube Specimens) |
| ASTM C 33 : 1985 | Standard Specification for Concrete Aggregates |
| ASTM C 150 : 2002 : REV A : EDT 1 | Standard Specification for Portland Cement |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.