• Shopping Cart
    There are no items in your cart

ASTM C 922 : 2021

Current

Current

The latest, up-to-date edition.

Standard Specification for Sintered Gadolinium Oxide-Uranium Dioxide Pellets for Light Water Reactors

Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

15-02-2021

€49.35
Excluding VAT

Committee
C 26
DocumentType
Standard
Pages
4
PublisherName
American Society for Testing and Materials
Status
Current
Supersedes

1.1This specification is for finished sintered (U,Gd)O2 pellets. It applies to (U,Gd)O2 pellets containing uranium (U) of any 235U concentration and any concentration of gadolinium oxide (Gd2O3) for use in nuclear reactors.

1.2This specification recognizes the presence of reprocessed U in the fuel cycle and consequently defines isotopic limits for (U,Gd)O2 pellets made from commercial grade UO2. Such commercial grade UO2 is defined so that, regarding fuel design and manufacture, the product is essentially equivalent to that made from unirradiated U. UO2 falling outside these limits cannot necessarily be regarded as equivalent and may thus need special provisions at the fuel fabrication plant or in the fuel design.

1.3This specification does not include (a) provisions for preventing criticality accidents, (b) requirements for health and safety, (c) avoidance of hazards, or (d) shipping precautions and controls. Observance of this specification does not relieve the user of the obligation to be aware of and conform to all applicable international, federal, state, and local regulations pertaining to possessing, shipping, processing, or using source or special nuclear material. Examples of U.S. Governmental documents are Code of Federal Regulations (Latest Edition), Title 10, Part 50, Title 10, Part 70, Title 10, Part 71, and Title 49, Part 173.

1.4Units—The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.5The following precautionary caveat pertains only to the technical requirements portion, Section 4, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ASTM C 1408 : 2016 Standard Test Method for Carbon (Total) in Uranium Oxide Powders and Pellets By Direct Combustion-Infrared Detection Method
ASTM C 1430 : 2018 Standard Test Method for Determination of Uranium, Oxygen to Uranium (O/U), and Oxygen to Metal (O/M) in Sintered Uranium Dioxide and Gadolinia-Uranium Dioxide Pellets by Atmospheric Equilibration
ASTM C 1502 : 2016 Standard Test Method for Determination of Total Chlorine and Fluorine in Uranium Dioxide and Gadolinium Oxide
ASTM C 968 : 2019 Standard Test Methods for Analysis of Sintered Gadolinium Oxide-Uranium Dioxide Pellets
ASTM C 1457 : 2018 Standard Test Method for Determination of Total Hydrogen Content of Uranium Oxide Powders and Pellets by Carrier Gas Extraction

ASTM C 859 : 2023 Standard Terminology Relating to Nuclear Materials
ASTM C 859 : 2014 : REV B Standard Terminology Relating to Nuclear Materials
ASTM C 859 : 2024 Standard Terminology Relating to Nuclear Materials
ASTM E 105 : 2021 Standard Guide for Probability Sampling of Materials
ASTM C 859 : 2022 Standard Terminology Relating to Nuclear Materials
ASTM C 859 : 2022 : REV A Standard Terminology Relating to Nuclear Materials
ASTM C 753 : 2016 : REV A Standard Specification for Nuclear-Grade, Sinterable Uranium Dioxide Powder
ASTM E 105 : 2016 Standard Practice for Probability Sampling of Materials
ASTM E 112 : 2013 : R2021 Standard Test Methods for Determining Average Grain Size
ASTM E 112 : 2013 Standard Test Methods for Determining Average Grain Size
ASTM E 112 : 2024 Standard Test Methods for Determining Average Grain Size
ASTM C 753 : 2016 : REV A : R2021 Standard Specification for Nuclear-Grade, Sinterable Uranium Dioxide Powder

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.