ASTM D 1004 : 2013 : REDLINE
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Tear Resistance (Graves Tear) of Plastic Film and Sheeting
06-03-2021
English
01-04-2013
Important note : Users cannot be edited or removed once added to your Multi user PDF.CONTAINED IN VOL. 08.01, 2015 Defines the determination of the tear resistance of flexible plastic film and sheeting at very low rates of loading, 51 mm [2 in.]/min. and is designed to measure the force to initiate tearing.
| Committee |
D 20
|
| DocumentType |
Redline
|
| Pages |
6
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy |
1.1This test method2 covers the determination of the tear resistance of flexible plastic film and sheeting at very low rates of loading, 51 mm (2 in.)/min. and is designed to measure the force to initiate tearing. The specimen geometry of this test method produces a stress concentration in a small area of the specimen. The maximum stress, usually found near the onset of tearing, is recorded as the tear resistance in newtons (or pounds-force). The method is not applicable for film or sheeting material where brittle failures occur during testing or where maximum extension is greater than 101.6 mm (4 in.).
1.1.1Although resistance to tear can be expressed in newtons per microns, (pounds-force per mil) of specimen thickness, this is only advisable where correlation for the particular material being tested has been established. In most cases, comparison between films of dissimilar thickness is not valid.
1.2Constant-Rate-of-Grip Separation Test—This test method employs a constant rate of separation of the grips holding the test specimen.
1.3The values stated in SI units are to be regarded as the standard. The values given in parentheses are provided for information only.
| ASTM D 1593 : 2013 : REDLINE | Standard Specification for Nonrigid Vinyl Chloride Plastic Film and Sheeting |
| ASTM D 5047 : 2017 : REDLINE | Standard Specification for Polyethylene Terephthalate Film and Sheeting |
| ASTM D 3664 : 2016 : REDLINE | Standard Specification for Biaxially Oriented Polymeric Resin Film for Capacitors in Electrical Equipment |
| ASTM D 4434/D4434M : 2015 : REDLINE | Standard Specification for Poly(Vinyl Chloride) Sheet Roofing |
| ASTM F 942 : 2002 | Standard Guide for Selection of Test Methods for Interlayer Materials for Aerospace Transparent Enclosures |
| ASTM D 7106 : 2005 : R2010 | Standard Guide for Selection of Test Methods for Ethylene Propylene Diene Terpolymer (EPDM) Geomembranes |
| ASTM D 2103 : 2015 : REDLINE | Standard Specification for Polyethylene Film and Sheeting |
| ASTM D 1922 : 2015 : REDLINE | Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method |
| ASTM F 1742 : 2003 | Standard Specification for PVC Insulating Sheeting |
| ASTM F 942 : 2002 : R2008 | Standard Guide for Selection of Test Methods for Interlayer Materials for Aerospace Transparent Enclosures |
| ASTM F 1742 : 2003 : EDT 1 | Standard Specification for PVC Insulating Sheeting |
| ACI 350.2R : 2004 | CONCRETE STRUCTURES FOR CONTAINMENT OF HAZARDOUS MATERIALS |
| BS ISO 12891-2:2014 | Retrieval and analysis of surgical implants Analysis of retrieved surgical implants |
| MIL-P-58102 Base Document:1978 | PLASTIC SHEET AND LAMINATES, FLEXIBLE FOR ENVIRONMENTAL PROTECTIVE STORAGE AND SHIPPING SYSTEMS |
| MIL-A-50424 Base Document:1969 | ACETAL, SHEETING (FOR USE WITH AMMUNITION) |
| ASTM D 7106/D7106M : 2005 : R2015 : EDT 1 | Standard Guide for Selection of Test Methods for Ethylene Propylene Diene Terpolymer (EPDM) Geomembranes |
| ASTM E 2731 : 2009 | Standard Specification for Materials to Mitigate the Spread of Radioactive Contamination after a Radiological Dispersion Event (Withdrawn 2018) |
| ASTM F 790 : 2008 : R2013 | Standard Guide for Testing Materials for Aerospace Plastic Transparent Enclosures |
| ASTM D 8065/D8065M : 2016 | Standard Classification System and Basis for Specification for Specifying Plastic Films |
| ASTM F 561 : 2013 | Standard Practice for Retrieval and Analysis of Medical Devices, and Associated Tissues and Fluids |
| ANSI/NEMA FI 3:2004 | Calendered Aramid Papers Used for Electrical Insulation |
| ASTM D 4068 : 2017 : REDLINE | Standard Specification for Chlorinated Polyethylene (CPE) Sheeting for Concealed Water-Containment Membrane |
| A-A-59520 Base Document:1999 | OVERSHOES, MEN'S AND WOMEN'S, BOOT, COMBAT |
| ASTM D 7008 : 2008 | Standard Specification for Geosynthetic Alternate Daily Covers |
| ASTM F 790 : 2008 | Standard Guide for Testing Materials for Aerospace Plastic Transparent Enclosures |
| ASTM D 4551 : 2017 : REDLINE | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Flexible Concealed Water-Containment Membrane |
| ASTM D 7008 : 2008 : R2013 | Standard Specification for Geosynthetic Alternate Daily Covers |
| ASTM F 942 : 2002 : R2013 | Standard Guide for Selection of Test Methods for Interlayer Materials for Aerospace Transparent Enclosures |
| AAMI TIR17 : 2008 | COMPATIBILITY OF MATERIALS SUBJECT TO STERILIZATION |
| AAMI TIR17 : 2017 | COMPATIBILITY OF MATERIALS SUBJECT TO STERILIZATION |
| ASTM D 7176 : 2006 | Standard Specification for Non-Reinforced Polyvinyl Chloride (PVC) Geomembranes Used in Buried Applications |
| ASTM F 2903 : 2011 | Standard Guide for Tissue Engineered Medical Products (TEMPs) for Reinforcement of Tendon and Ligament Surgical Repair (Withdrawn 2020) |
| ASTM D 5747/D5747M : 2008 : R2013 : EDT 1 | Standard Practice for Tests to Evaluate the Chemical Resistance of Geomembranes to Liquids |
| ASTM D 3105 : 2017 : REDLINE | Standard Index of Methods for Testing Elastomeric and Plastomeric Roofing and Waterproofing Materials |
| NACE RP 06 75 : 1988 | CORROSION CONTROL OF OFFSHORE STEEL PIPELINES |
| L-P-375 Revision D:1994 | PLASTIC FILM, FLEXIBLE, VINYL CHLORIDE |
| 13/30242622 DC : 0 | BS ISO 12891-2 - RETRIEVAL AND ANALYSIS OF SURGICAL IMPLANTS - PART 2: ANALYSIS OF RETRIEVED SURGICAL IMPLANTS |
| ASTM D 7176 : 2006 : R2011 | Standard Specification for Non-Reinforced Polyvinyl Chloride (PVC) Geomembranes Used in Buried Applications |
| ISO 12891-2:2014 | Retrieval and analysis of surgical implants Part 2: Analysis of retrieved surgical implants |
| ASTM D 7192 : 2010 | Standard Test Method for High Speed Puncture Properties of Plastic Films Using Load and Displacement Sensors |
| ASTM D 7067 : 2005 | Standard Specification for Reinforced White PIB Sheet Used in Roofing Membrane (Withdrawn 2014) |
| ASTM D 7106 : 2005 | Standard Guide for Selection of Test Methods for Ethylene Propylene Diene Terpolymer (EPDM) Geomembranes |
| L-F-333 Revision A:1974 | FILM, PHOTOGRAPHIC, MOTION PICTURE (BLACK AND WHITE) |
| BS PAS 1008(2014) : 2014 | SPECIFICATION FOR THE PERFORMANCE AND TESTING OF A SINGLE-USE FLEXITANK |
| A-A-2790 Base Document:1992 | ENVELOPE, TRANSPARENT |
| L-F-320 Revision B:1965 | FILM, THERMAL DEVELOPING |
| A-A-56021 Base Document:1991 | PLASTIC SHEET, POLYETHYLENE, TEREPHTHALATE (FOR CARTOGRAPHIC OPERATIONS) |
| SAE AMS3529B | Plastic Sheet and Film, Vinyl Copolymers Unplasticized |
| ASTM E 1420 : 1991 | Practice for Specifying Polymeric Materials for Service in Ionizing Radiation Environments (Withdrawn 1996) |
| ASTM F 1742 : 2003 : R2011 | Standard Specification for PVC Insulating Sheeting |
| ASTM D 618 : 2013 : REDLINE | Standard Practice for Conditioning Plastics for Testing |
| ASTM D 6988 : 2013 : REDLINE | Standard Guide for Determination of Thickness of Plastic Film Test Specimens |
| ASTM D 4000 : 2016 : REDLINE | Standard Classification System for Specifying Plastic Materials |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.