ASTM D 1126 : 2002
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Hardness in Water
Hardcopy , PDF
11-11-2014
English
10-05-2002
Important note : Users cannot be edited or removed once added to your Multi user PDF.| Committee |
D 19
|
| DocumentType |
Test Method
|
| Pages |
4
|
| ProductNote |
Reconfirmed 2002
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1 This test method covers the determination of hardness in water by titration. This test method is applicable to waters that are clear in appearance and free of chemicals that will complex calcium or magnesium. The lower detection limit of this test method is approximately 2 to 5 mg/L as CaCO3; the upper limit can be extended to all concentrations by sample dilution. It is possible to differentiate between hardness due to calcium ions and that due to magnesium ions by this test method.
1.2 This test method was tested on reagent water only. It is the user's responsibility to ensure the validity of the test method for waters of untested matrices.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| ASTM D 6210 : 2017 | Standard Specification for Fully-Formulated Glycol Base Engine Coolant for Heavy-Duty Engines<rangeref></rangeref > |
| ASTM D 5752 : 2010 : R2017 | Standard Specification for Supplemental Coolant Additives (SCAs) for Use in Precharging Coolants for Heavy-Duty Engines |
| ASTM D 7715 : 2012 : R2016 : EDT 1 | Standard Specification for Fully-Formulated Glycerin Base Engine Coolant for Heavy-Duty Engines |
| ASTM D 3376 : 2018 | Standard Test Methods of Sampling and Testing Pulps to be Used in the Manufacture of Electrical Insulation |
| ASTM E 1910/E1910M : 2015 | Standard Test Method for Agricultural pH Control Agents, Measurement of pH Change and Buffering Capacity |
| ASTM D 6469 : 2017 | Standard Guide for Microbial Contamination in Fuels and Fuel Systems |
| ASTM D 8039 : 2016 | Standard Specification for Heat Transfer Fluids (HTF) for Heating and Air Conditioning (HVAC) Systems |
| ASTM E 1391 : 2003 : R2014 | Standard Guide for Collection, Storage, Characterization, and Manipulation of Sediments for Toxicological Testing and for Selection of Samplers Used to Collect Benthic Invertebrates |
| ASTM D 7517 : 2019 | Standard Specification for Fully-Formulated 1,3 Propanediol (PDO) Base Engine Coolant for Heavy-Duty Engines |
| ASTM E 1945 : 2002 : R2016 | Standard Test Method for Percent Dispersibility |
| ASTM C 500/C500M : 2007 : R2019 | Standard Test Methods for Asbestos-Cement Pipe (Withdrawn 2022) |
| ASTM D 1782 : 2017 | Standard Test Methods for Operating Performance of Particulate Cation-Exchange Materials |
| ASTM C 375 : 1958 : R2016 | Standard Classification of Water Used in Milling of Porcelain Enamel |
| ASTM E 1116 : 1998 : R2014 | Standard Test Method for Emulsification Characteristics of Pesticide Emulsifiable Concentrates |
| ASTM D 3342 : 1990 : R2017 | Standard Test Method for Dispersion Stability of New (Unused) Rolling Oil Dispersions in Water |
| ASTM E 1673 : 1996 : R2017 | Standard Test Method for Percent Suspensibility |
| ASTM D 2946 : 2001 : R2018 | Standard Terminology for Asbestos and Asbestos–Cement Products (Withdrawn 2022) |
| ASTM D 4985 : 2010 : R2015 | Standard Specification for Low Silicate Ethylene Glycol Base Engine Coolant for Heavy Duty Engines Requiring a Pre-Charge of Supplemental Coolant Additive (SCA) |
| ASTM D 7518 : 2010 : R2015 : EDT 1 | Standard Specification for 1,3 Propanediol (PDO) Base Engine Coolant for Automobile and Light-Duty Service |
| ASTM D 3306 : 2019 | Standard Specification for Glycol Base Engine Coolant for Automobile and Light-Duty Service |
| ASTM D 7714 : 2011 : R2016 : EDT 1 | Standard Specification for Glycerin Base Engine Coolant for Automobile and Light-Duty Service |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.