ASTM D 1177 : 2022
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Freezing Point of Aqueous Engine Coolants
English
01-09-2022
12-08-2026
| Committee |
D 15
|
| DocumentType |
Test Method
|
| Pages |
4
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This test method covers the determination of the freezing point of an aqueous engine coolant solution in the laboratory.
Note 1:Where solutions of specific concentrations are to be tested, they shall be prepared from representative samples as directed in Practice D1176. Secondary phases separating on dilution need not be separated.
Note 2:These products may also be marketed in a ready-to-use form (prediluted).
1.2The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.
1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM D 4985 : 2010 : R2015 | Standard Specification for Low Silicate Ethylene Glycol Base Engine Coolant for Heavy Duty Engines Requiring a Pre-Charge of Supplemental Coolant Additive (SCA) |
| ASTM D 6660 : 2001 : R2019 | Standard Test Method for Freezing Point of Aqueous Ethylene Glycol Base Engine Coolants by Automatic Phase Transition Method |
| ASTM D 7713 : 2018 | Standard Specification for Aqueous Engine Coolant Grade Glycol (53 % by Volume Nominal) |
| ASTM D 3321 : 2019 | Standard Test Method for Use of the Refractometer for Field Test Determination of the Freezing Point of Aqueous Engine Coolants |
| ASTM D 3585 : 2008 : R2020 | Standard Specification for ASTM Reference Fluid for Coolant Tests |
| ASTM D 7518 : 2020 | Standard Specification for 1,3 Propanediol (PDO) Base Engine Coolant for Automobile and Light-Duty Service |
| ASTM D 7714 : 2011 : R2021 | Standard Specification for Glycerin Base Engine Coolant for Automobile and Light-Duty Service |
| ASTM D 3306 : 2021 | Standard Specification for Glycol Base Engine Coolant for Automobile and Light-Duty Service |
| ASTM D 7583 : 2016 | Standard Test Method for John Deere Coolant Cavitation Test |
| ASTM D 8039 : 2016 | Standard Specification for Heat Transfer Fluids (HTF) for Heating and Air Conditioning (HVAC) Systems |
| ASTM D 8566 : 2024 | Standard Specification for Glycol-Based Electric Vehicle Coolant with Low Electrical Conductivity |
| ASTM D 8565 : 2024 | Standard Specification for Glycol-Based Coolants for Fuel Cell Electric Vehicles |
| ASTM D 7713 : 2018 : R2023 | Standard Specification for Aqueous Engine Coolant Grade Glycol (53 % by Volume Nominal) |
| ASTM D 3585 : 2024 | Standard Specification for ASTM Reference Fluid for Coolant Tests |
| ASTM D 8039 : 2016 : R2023 | Standard Specification for Heat Transfer Fluids (HTF) for Heating and Air Conditioning (HVAC) Systems |
| ASTM D 4985 : 2010 : R2023 | Standard Specification for Low Silicate Ethylene Glycol Base Engine Coolant for Heavy Duty Engines Requiring a Pre-Charge of Supplemental Coolant Additive (SCA) |
| ASTM D 6660 : 2001 : R2023 | Standard Test Method for Freezing Point of Aqueous Ethylene Glycol Base Engine Coolants by Automatic Phase Transition Method |
| ASTM D 3321 : 2026 | Standard Test Method for Use of Handheld Refractometers for the Determination of the Freeze Point and % Glycol of Aqueous Engine Coolants |
| ASTM E 1 : 2014 : R2025 | Standard Specification for ASTM Liquid-in-Glass Thermometers |
| ASTM D 1176 : 2014 : R2026 | Standard Practice for Sampling and Preparing Aqueous Solutions of Engine Coolants or Antirusts for Testing Purposes |
| ASTM E 1 : 2014 : R2020 | Standard Specification for ASTM Liquid-in-Glass Thermometers |
| ASTM D 1176 : 2014 : R2019 | Standard Practice for Sampling and Preparing Aqueous Solutions of Engine Coolants or Antirusts for Testing Purposes |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : Users cannot be edited or removed once added to your Multi user PDF.