ASTM D 1331 : 2020 : R2024
Current
The latest, up-to-date edition.
Standard Test Methods for Surface and Interfacial Tension of Solutions of Paints, Solvents, Solutions of Surface-Active Agents, and Related Materials
Hardcopy , PDF
English
24-06-2024
Committee |
D 01
|
DocumentType |
Test Method
|
Pages |
6
|
PublisherName |
American Society for Testing and Materials
|
Status |
Current
|
Supersedes |
1.1These test methods cover the determination of surface tension and interfacial tension of a variety of liquid materials, including but not restricted to paints, solvents, and solutions of surface-active agents, as defined in Terminology D459. Four methods are covered as follows:
Method A—Surface Tension by du Noüy ring;
Method B—Interfacial Tension by du Noüy ring;
Method C—Surface Tension by Wilhelmy plate; and
Method D—Interfacial Tension by Wilhelmy plate.
1.2Method A originally was written primarily to cover aqueous solutions of surface-active agents, but is also applicable to aqueous paints, nonaqueous solutions (including paints) and mixed solvent solutions.
1.3Method B is applicable to two-phase solutions. More than one solute component may be present, including solute components that are not in themselves surface-active.
1.4Method C is applicable to surface active liquids and, unlike du Noüy ring, no buoyancy corrections are needed and results are not affected by moderate viscosities (1-10 Pa-sec) of the liquid. It is the recommended method for use with paints and resin solutions.
1.5Method D is applicable to two-phase solutions and mixtures.
1.6The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.7This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Material Safety Data Sheets are available for reagents and materials. Review them for hazards prior to usage.
1.8This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM D 6469 : 2024 | Standard Guide for Microbial Contamination in Fuels and Fuel Systems |
ASTM D 8506 : 2023 | Standard Guide for Microbial Contamination and Biodeterioration in Turbine Oils and Turbine Oil Systems |
ASTM F 1359/F1359M : 2022 | Standard Test Method for Liquid Penetration Resistance of Protective Clothing or Protective Ensembles Under a Shower Spray While on a Manikin |
ASTM F 1670/F1670M : 2024 | Standard Test Method for Resistance of Materials Used in Protective Clothing to Penetration by Synthetic Blood |
ASTM F 1671/F1671M : 2022 | Standard Test Method for Resistance of Materials Used in Protective Clothing to Penetration by Blood-Borne Pathogens Using Phi-X174 Bacteriophage Penetration as a Test System |
ASTM D 7826 : 2023 : REV B | Standard Guide for Evaluation of New Aviation Gasolines and New Aviation Gasoline Additives |
ASTM F 2161 : 2021 | Standard Guide for Instrument and Precision Bearing Lubricants—Part 1 Oils |
ASTM F 1862/F1862M : 2024 | Standard Test Method for Resistance of Medical Face Masks to Penetration by Synthetic Blood (Horizontal Projection of Fixed Volume at a Known Velocity) |
ASTM D 1417 : 2016 : R2021 | Standard Test Methods for Rubber Latices—Synthetic |
ASTM F 1819 : 2019 | Standard Test Method for Resistance of Materials Used in Protective Clothing to Penetration by Synthetic Blood Using a Mechanical Pressure Technique |
ASTM D 4751 : 2021 : REV A | Standard Test Methods for Determining Apparent Opening Size of a Geotextile |
ASTM D 4054 : 2023 | Standard Practice for Evaluation of New Aviation Turbine Fuels and Fuel Additives |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.