• Shopping Cart
    There are no items in your cart

ASTM D 1556/D1556M : 2024

Current

Current

The latest, up-to-date edition.

Standard Test Method for Density and Unit Weight of Soil in Place by Sand-Cone Method

Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

15-10-2024

€56.53
Excluding VAT

Committee
D 18
DocumentType
Test Method
Pages
8
PublisherName
American Society for Testing and Materials
Status
Current
Supersedes

1.1This test method may be used to determine the in-place density and unit weight of soils using a sand cone apparatus.

1.2This test method is applicable for soils without appreciable amounts of rock or coarse materials in excess of 11/2in. [38 mm] in diameter.

1.3This test method may also be used for the determination of the in-place density and unit weight of intact or in situ soils, provided the natural void or pore openings in the soil are small enough to prevent the sand used in the test from entering the voids. The soil or other material being tested shall have sufficient cohesion or particle attraction to maintain stable sides on a small hole or excavation, and be firm enough to withstand the minor pressures exerted in digging the hole and placing the apparatus over it, without deforming or sloughing.

1.4This test method is not suitable for organic, saturated, or highly plastic soils that would deform or compress during the excavation of the test hole. This test method may not be suitable for soils consisting of unbound granular materials that will not maintain stable sides in the test hole, soils containing appreciable amounts of coarse material larger than 11/2in. [38 mm], and granular soils having high void ratios.

1.5When materials to be tested contain appreciable amounts of particles larger than 11/2in. [38 mm], or when test hole volumes larger than 0.1 ft3 [2830 cm3] are required, Test Method D4914/D4914M or D5030/D5030M is applicable.

1.6Units—The values stated in either inch-pound units or SI units [presented in brackets] are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

1.6.1The gravitational system of inch-pound units is used when dealing with inch-pound units. In this system, the pound (lbf) represents a unit of force (weight), while the units for mass is slugs. The slug unit is not given, unless dynamic (F = ma) calculations are involved.

1.6.2It is common practice in the engineering/construction profession to use, interchangeably, units representing both mass and force unless dynamic calculations (F = Ma) are involved. The practice implicitly combines two separate systems of units; the absolute and gravitational systems. It is scientifically undesirable to combine the use of two separate systems within a single standard. As stated, this standard includes the gravitational system of inch-pound units and does not use/present the slug unit of mass. However, the use of balances and scales recording pounds of mass (lbm), or recording density in lbm/ft3 shall not be regarded as nonconformance with this standard.

1.6.3The sieve designations are identified using the “standard” system in accordance with Specification E11, such as 25 mm and 75 μm, followed by the “alternative” system of 1 in. and No. 200, respectively.

1.7All observed and calculated values shall conform to the guidelines for significant digits and rounding established in Practice D6026, unless superseded by this test method.

1.7.1For purposes of comparing, a measured or calculated value(s) with specified limits, the measured or calculated value(s) shall be rounded to the nearest decimal of significant digits in the specified limits.

1.7.2The procedures used to specify how data are collected/recorded or calculated in this standard are regarded as the industry standard. In addition, they are representative of the significant digits that generally should be retained. The procedures used do not consider material variation, purpose for obtaining the data, special purpose studies, or any considerations for the user’s objectives; and it is common practice to increase or reduce significant digits of reported data to be commensurate with these considerations. It is beyond the scope of this standard to consider significant digits used in analysis methods for engineering design.

1.8This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.9This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ASTM D 6460 : 2024 Standard Test Method for Determination of Rolled Erosion Control Product (RECP) Performance in Protecting Earthen Channels from Stormwater-Induced Erosion
ASTM D 7830/D7830M : 2014 : R2021 : EDT 1 Standard Test Method for In-Place Density (Unit Weight) and Water Content of Soil Using an Electromagnetic Soil Density Gauge
ASTM D 5080 : 2020 Standard Test Method for Rapid Determination of Percent Compaction
ASTM D 5874 : 2024 Standard Test Methods for Determination of the Impact Value (IV) of a Soil
ASTM B 789/B789M : 2016 : R2021 Standard Practice for Installing Corrugated Aluminum Structural Plate Pipe for Culverts and Sewers
ASTM D 8153 : 2022 Standard Test Method for Determination of Soil Water Contents Using a Dielectric Permittivity Probe
ASTM B 788/B788M : 2009 : R2020 Standard Practice for Installing Factory-Made Corrugated Aluminum Culverts and Storm Sewer Pipe
ASTM F 1668 : 2016 : R2022 Standard Guide for Construction Procedures for Buried Plastic Pipe
ASTM D 4718/D4718M : 2015 : R2023 Standard Practice for Correction of Unit Weight and Water Content for Soils Containing Oversize Particles
ASTM D 7277 : 2016 : R2023 Standard Test Method for Performance Testing of Articulating Concrete Block (ACB) Revetment Systems for Hydraulic Stability in Open Channel Flow

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.