ASTM D 1693 : 2015
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Environmental Stress-Cracking of Ethylene Plastics
Available format(s)
Hardcopy , PDF
Superseded date
03-09-2020
Superseded by
Language(s)
English
Published date
12-06-2015
Important note : Users cannot be edited or removed once added to your Multi user PDF.This test method covers the determination of the susceptibility of ethylene plastics, as defined in Terminology D883, to environmental stress-cracking when subjected to the conditions herein specified.
| Committee |
D 20
|
| DocumentType |
Test Method
|
| Pages |
11
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This test method covers the determination of the susceptibility of ethylene plastics, as defined in Terminology D883, to environmental stress-cracking when subjected to the conditions herein specified. Under certain conditions of stress and in the presence of environments such as soaps, wetting agents, oils, or detergents, ethylene plastics may exhibit mechanical failure by cracking.
1.2The values stated in SI units are to be regarded as standard.
1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Note 1:There is no known ISO equivalent to this standard.
| ASTM F 2718 : 2009 : R2015 | Standard Specification for Polyethylene (PE) and Cement Materials for an Encapsulated Cement Mortar Formed in Place Liner System (FIPLS) for the Rehabilitation of Water Pipelines (Withdrawn 2022) |
| ASTM F 810 : 2012 : R2018 | Standard Specification for Smoothwall Polyethylene (PE) Pipe for Use in Drainage and Waste Disposal Absorption Fields |
| ASTM D 3350 : 2014 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
| ASTM D 2308 : 2007 : R2013 | Standard Specification for Thermoplastic Polyethylene Jacket for Electrical Wire and Cable |
| ASTM D 3485 : 2015 | Standard Specification for Coilable High Density Polyethylene (HDPE) Cable in Conduit (CIC) |
| ASTM D 4000 : 2016 | Standard Classification System for Specifying Plastic Materials |
| ASTM D 7082 : 2015 | Standard Specification for Polyethylene Stay In Place Form System for End Walls for Drainage Pipe |
| ASTM D 7436 : 2017 | Standard Classification System for Unfilled Polyethylene Plastics Molding and Extrusion Materials with a Fractional Melt Index Using ISO Protocol and Methodology |
| ASTM F 2160 : 2016 | Standard Specification for Solid Wall High Density Polyethylene (HDPE) Conduit Based on Controlled Outside Diameter (OD) |
| ASTM D 1248 : 2016 | Standard Specification for Polyethylene Plastics Extrusion Materials for Wire and Cable |
| ASTM D 4565 : 2015 | Standard Test Methods for Physical and Environmental Performance Properties of <brk/>Insulations and Jackets for Telecommunications Wire and Cable |
| ASTM F 2896 : 2011 : R2017 | Standard Specification for Reinforced Polyethylene Composite Pipe For The Transport Of Oil And Gas And Hazardous Liquids |
| ASTM D 1998 : 2015 | Standard Specification for Polyethylene Upright Storage Tanks |
| ASTM D 3554 : 2007 : R2018 | Standard Specification for Track-Resistant Black Thermoplastic High-Density Polyethylene Insulation for Wire and Cable, 75 °C Operation |
| ASTM D 4976 : 2012 : REV A | Standard Specification for Polyethylene Plastics Molding and Extrusion Materials |
| ASTM D 4703 : 2002 | Standard Practice for Compression Molding Thermoplastic Materials into Test Specimens, Plaques, or Sheets |
| ASTM D 1248 : 2002 | Standard Specification for Polyethylene Plastics Extrusion Materials For Wire and Cable |
| ASTM D 1204 : 2007 | Standard Test Method for Linear Dimensional Changes of Nonrigid Thermoplastic Sheeting or Film at Elevated Temperature |
| ASTM D 1248 : 1984 : R1989 : EDT 1 | Standard Specification for Polyethylene Plastics Molding and Extrusion Materials |
| ASTM D 4976 : 2006 | Standard Specification for Polyethylene Plastics Molding and Extrusion Materials |
| ASTM D 4976 : 2000 : REV B | Standard Specification for Polyethylene Plastics Molding and Extrusion Materials |
| ASTM D 1204 : 2014 | Standard Test Method for Linear Dimensional Changes of Nonrigid Thermoplastic Sheeting or Film at Elevated Temperature |
| ASTM D 1248 : 2012 | Standard Specification for Polyethylene Plastics Extrusion Materials for Wire and Cable |
| ASTM D 3350 : 2000 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
| ASTM D 4976 : 2004 : REV A | Standard Specification for Polyethylene Plastics Molding and Extrusion Materials |
| ASTM D 4976 : 2004 | Standard Specification for Polyethylene Plastics Molding and Extrusion Materials |
| ASTM D 4703 : 2003 | Standard Practice for Compression Molding Thermoplastic Materials into Test Specimens, Plaques, or Sheets |
| ASTM D 3350 : 2008 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
| ASTM D 1248 : 2016 | Standard Specification for Polyethylene Plastics Extrusion Materials for Wire and Cable |
| ASTM D 4703 : 1993 | Standard Practice for Compression Molding Thermoplastic Materials into Test Specimens, Plaques, or Sheets |
| ASTM D 1204 : 2008 | Standard Test Method for Linear Dimensional Changes of Nonrigid Thermoplastic Sheeting or Film at Elevated Temperature |
| ASTM D 3350 : 2002 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
| ASTM D 3350 : 2014 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
| ASTM D 1204 : 2014 : R2020 | Standard Test Method for Linear Dimensional Changes of Nonrigid Thermoplastic Sheeting or Film at Elevated Temperature |
| ASTM D 4976 : 2012 | Standard Specification for Polyethylene Plastics Molding and Extrusion Materials |
| ASTM D 4703 : 2010 | Standard Practice for Compression Molding Thermoplastic Materials into Test Specimens, Plaques, or Sheets |
| ASTM D 3350 : 2004 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
| ASTM D 3350 : 2002 : REV A | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
| ASTM D 3350 : 2012 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
| ASTM D 3350 : 2001 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
| ASTM D 4976 : 2002 | Standard Specification for Polyethylene Plastics Molding and Extrusion Materials |
| ASTM D 3350 : 2012 : EDT 1 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
| ASTM D 1248 : 2004 | Standard Specification for Polyethylene Plastics Extrusion Materials For Wire and Cable |
| ASTM D 3350 : 2010 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
| ASTM D 1204 : 1994 : EDT 1 | Standard Test Method for Linear Dimensional Changes of Nonrigid Thermoplastic Sheeting or Film at Elevated Temperature |
| ASTM D 3350 : 2006 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
| ASTM D 4976 : 2002 : EDT 1 | Standard Specification for Polyethylene Plastics Molding and Extrusion Materials |
| ASTM D 3350 : 2010 : REV A | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
| ASTM D 4703 : 2000 | Standard Practice for Compression Molding Thermoplastic Materials into Test Specimens, Plaques, or Sheets |
| ASTM D 4703 : 2010 : REV A | Standard Practice for Compression Molding Thermoplastic Materials into Test Specimens, Plaques, or Sheets |
| ASTM D 4703 : 2016 | Standard Practice for Compression Molding Thermoplastic Materials into Test Specimens, Plaques, or Sheets |
| ASTM D 1204 : 2002 | Standard Test Method for Linear Dimensional Changes of Nonrigid Thermoplastic Sheeting or Film at Elevated Temperature |
| ASTM D 3350 : 2005 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
| ASTM D 4976 : 2012 : REV A | Standard Specification for Polyethylene Plastics Molding and Extrusion Materials |
| ASTM D 4703 : 2007 | Standard Practice for Compression Molding Thermoplastic Materials into Test Specimens, Plaques, or Sheets |
| ASTM D 1248 : 2000 : REV A | Standard Specification for Polyethylene Plastics Extrusion Materials For Wire and Cable |
| ASTM D 1248 : 2005 | Standard Specification for Polyethylene Plastics Extrusion Materials For Wire and Cable |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.